HP D7171A - NetServer - LPr Manuale utente

IBM OS/2 Warp Server for e-Business

Installation Guide for Hewlett-Packard

NetServers

NOTICE: The information in this document was last updated for the HP NetServer Navigator CD-ROM version L.17.01. If you

don't have the L.17.01 version CD-ROM and you're obtaining this document from the HP NetServer web site as a reference to

install an operating system, be sure to also check the HP NetServer web site for the latest available drivers.

©Copyright Hewlett-Packard Company

September 7, 1999

(This document is only available in English.)

Introduction

The objective of this document is to help Hewlett-Packard customers install IBM OS/2 Warp

Server for e-business on a HP NetServer system. For additional information on Hewlett-Packard

NetServers refer to the HP Information Assistant on the HP NetServer Navigator CD-ROM.

It is critical to know which disk adapters or disk array adapter are in the system before you start

the installation. The tables in the Appendix will help you identify what adapter is implemented or

embedded on the system board for each HP NetServer.

NOTE: The IBM OS/2 Warp Server for e-business is not supported on the HP NetServer

E series (E 30, E 40, E 45, E 50, and E 60).

Table of Contents

Installation Procedure: OS/2 Warp Server for e-business

Requirements

Creating the HP Drivers/Utilities Diskette

Installation Steps

APPENDIX

Installation Procedure: OS/2 Warp Server for e-business

Requirements

•Driver's Diskette for OS/2 Warp Server for e-business created from the HP NetServer

Navigator CD diskette library.

•OS/2 Warp Server for e-business CD

•Installation diskettes (to create installation diskettes from OS/2 CD insert you OS/2 CD in the

CD-ROM drive and type CDINST).

NOTE: I2O Mode is not supported by IBM OS/2 operating system, If there is a NetRAID

adapter in the system set the NetRAID mode to Mass-Storage using Set Class utility or

NetRAID's utility (Ctrl+M) before installing OS/2.

Creating the HP Drivers/Utilities Diskette

The "Drivers/Utilities" diskette is referred to in the HP NetServer Navigator CD-ROM and other

HP documentation as the "Drivers Diskette." The purpose of this diskette is to accomplish the

following three tasks:

Task 1) To backup one (or more) of your OS/2 installation diskettes. For OS/2 Warp and later

products, only Diskette 1 is backed up. We will refer to this backup copy of OS/2 Diskette 1 as

the "Work Diskette 1". When you install OS/2, you will use the backup copies in place of the

original diskettes that came in the OS/2 box.

Task 2) Identify the unused drivers on "Work Diskette 1" to make room for new drivers. Delete

the unwanted drivers from the "Work Diskette 1".

Task 3) Identify the required drivers for the system. Based on the boot setup. The following

drivers may be needed. Example:

AIC7870.ADD

SYM_HI.ADD

MRAID.ADD

Make a list of drivers that are needed and order them based on boot priority.

Task 4) Create the HP Drivers/Utility Diskette by stepping through one of the following

procedures. There are two ways to create the drivers diskette.

•Procedure One: Uses the OS/NOS icon section of the Navigator CD-ROM.

•Procedure Two: Uses the "Library diskette" section of the Navigator CD-ROM.

Procedure One

1. Boot the system from the HP Navigator CD-ROM.

2. From the Main Menu, select "Configuration Assistant and Installation Assistant".

3. Select Custom.

4. Select OS/2.

5. From the menu, select the version of OS/2 that you want to Install.

6. Read the information provided on the "Configuration Advisor" panel. Save the

information to a floppy diskette if you desire.

7. Select Continue.

8. From the "Custom Configuration" menu select "Create Drivers Diskette".

9. Label a blank diskette "HP NetServer IBM OS/2 Warp Drivers/Utilities Diskette".

Insert this diskette in drive A and select "Execute".

10. Remove the HP Navigator CD-ROM. Keep the newly created "Drivers/Utilities"

diskette in the floppy drive

11. Click on Exit. Select Yes to reboot system. Continue to Task 5.

Procedure Two

This is an alternate procedure for creating the "Drivers/Utilities" diskette using a section

called "Diskette Library" on the Navigator CDROM.

Keep in mind that if you need high resolution video, you will need to create additional video

drivers diskettes.

Use this procedure to create a "Drivers/Utilities" diskette using the "Diskette Library" on the

Navigator CDROM:

1. Boot the system from the HP Navigator CD-ROM

2. Select “NetServer Utilities”

3. Select “Diskette Library”

4. Select "NOS Drivers - OS/2 Warp Family" and then select “execute”.

5. Label a blank diskette “HP NetServer IBM OS/2 Warp Drivers/Utilities Diskette”, insert

the diskette when prompted and follow the instructions.

6. If needed, create the video driver diskettes by following the same procedure.

7. Click “Exit” when done.

8. Click “Yes”, to reboot the system. Continue to Task 5.

Task 5) Copy the required drivers (which are identified in Task 3) from the "HP

Drivers/Utilities” diskette to the "Work Diskette 1".

NOTE: Do not copy the NIC driver onto the diskette #1. The NIC driver can be loaded

during Network setup at the end of the installation.

Task 6) Edit the Config.sys file in "Work Diskette 1" to include the drivers entry which are

added in Task 5 and delete drivers entry which are removed in Task 2.

Task 7) Include "set copyfromfloppy=1" as the first line in config.sys in "Work Diskette 1" to

allow the installation process to copy drivers from floppy than from OS/2 Installation CDROM.

Installation Steps

1. Insert the Installation diskette and reboot your system.

2. Remove the Installation diskette and insert the Diskette #1 press Enter.

3. Replace the Diskette #1 with Diskette #2 and press Enter.

4. Insert the OS/2 Warp Server for e-business CD into the CD-ROM drive and press Enter.

5. At the Welcome Screen press Enter.

6. At the OS/2 Warp Server for e-business Installation screen press Enter to begin the

installation.

7. At the Volumes too small screen press Enter to modify the volumes sizes.

8. At the Modifying Volumes Warning screen press Enter.

9. At the Logical Volume Management Tool screen press Enter to continue.

NOTE: Logical Volume Management Tool will come up with logical view, to see the

physical view press F5.

10. Press Enter to install the Boot Manager.

NOTE: At this point only CD-ROM drive will be highlighted.

11. Select Install Boot Manager.

12. Press Enter again and select create a new volume.

13. Select create a volume that can be made Bootable and press Enter .

14. Select the drive letter C: for your boot drive and press Enter.

15. Type OS/2 for the volume name and press Enter.

16. Select a disk to be used to create the volume and press Enter.

17. Allocate from free space is highlighted, press Enter.

18. Free space is highlighted, press Enter.

19. Select a name for the partition C: and press Enter.

20. Select a size in megabytes for the partition and press Enter.

NOTE: If boot drive will be formatted as FAT, it should be less than 2GB.

21. Highlight the volume you just created and press Enter.

22. Select Set the Volume Installable and press Enter.

23. Press F3 to Exit LVM.

24. Save the changes and exit.

NOTE: Additional drives in the system should be partitioned and formatted after OS/2

installation is completed. Volume type selection is optional based on customer's need

(Compatibility Volume or LVM Volume).

25. Replace the diskette #2 with the Installation diskette and press Ctrl-Alt-Del.

26. Insert diskette #1 and press Enter.

27. Insert diskette #2 and press Enter.

28. At the Welcome screen press Enter.

29. At the OS/2 Warp Server for e-business installation screen press Enter.

30. At Installation Volume Selection, highlight Accept the volume and press Enter.

31. At Formatting the Installation Volume, highlight Perform a quick format and press

Enter.

32. At the select the File System screen , select High Performance and press Enter.

33. Remove the diskette and press Enter to restart the workstation and continue the installation.

34. At System Configuration click on Next to accept the default.

35. Click on Next again.

36. At Country Information select United States and press OK.

37. At Select System Default Printer, select Do Not Install default Printer.

NOTE: If you are installing a printer select the proper driver for it.

38. At Primary Display Driver Install, select VGA.

39. At the OS/2 Warp Server for e-business Setup and Installation, accept the default and

press Next.

40. After base operating system installation and configuration are complete press Next to begin

the Server Component installation.

41. At Information Screen, Do Not enter anything and click on Next.

42. At the Services screen, accept the default and click on Next.

43. At the Configuration screen, click on UserID and Password:

Enter USERID for UserID

Enter PASSWORD for Password

44. Click on File and Print Sharing Services and specify the Server name and Domain name.

45. Click on Network Adapters and Protocol Services, and load the NIC driver from the

Drivers Diskette you created from the HP NetServer Navigator CD and add the desired

Protocol.

46. Click on Install then click on OK.

47. Remove the NIC driver diskette, installation will continue until it is completed.

APPENDIX

This section provides additional information about HP NetServers and Disk Array Adapters used

with HP NetServers.

Table #1

NetServer #Ports SCSI Chip Driver Name

========= ====== ========= ===========

LX 2 AIC7880 AIC7870.ADD

LS 2 AIC7870 AIC7870.ADD

LH Pro 2 AIC7880 AIC7870.ADD

LH II 2 AIC7880 AIC7870.ADD

LH 3 2 SYM53c895 SYM8XX.ADD

LH 4 2 SYM53c895 SYM8XX.ADD

LH 3000 2 SYM53c896 SYM_HI.ADD

" 1 AIC7880 (SE)* AIC7870.ADD

LD Pro 1 AIC7880 AIC7870.ADD

LC 1 AIC7700 AIC7770.ADD

LC II 1 AIC7880 AIC7870.ADD

LC 3 1 AIC7880 AIC7870.ADD

LC 2000 2 SYM53c896 SYM_HI.ADD

E 40 1 AIC7860 AIC7870.ADD

E 45 1 AIC7860 AIC7870.ADD

E 50 1 AIC7880 AIC7870.ADD

E 60 2 AIC7895 AIC7870.ADD

LPr 1 SYM895 SYM8XX.ADD

* (SE stands for Single Ended)

Table #2

List of Hewlett-Packard Disk Array adapters and Drivers.

NetServer Adapter Name Driver Name

========= ============= ===========

E 30 NetRaid mraid.add

E 40 NetRaid mraid.add

E 45 NetRaid mraid.add

E 50 NetRaid mraid.add

E 60 NetRaid mraid.add

LC Mylex EISA 3609A hpda.add

LC Mylex PCI C3610A hpda.add

LC II NetRaid mraid.add

LC 3 NetRaid mraid.add

LC 2000 NetRaid mraid.add

LD Mylex PCI C3610A hpda.add

LD Pro Mylex PCI C3610A hpda.add

LF Mylex EISA 3609A hpda.add

LH Mylex PCI C3610A hpda.add

LH Pro Mylex PCI C3610A hpda.add

LH Pro NetRaid mraid.add

LH II NetRaid mraid.add

LH 3 NetRaid (*) mraid.add

LH 4 NetRaid (*) mraid.add

LH 3000 NetRaid (*) mraid.add

LM (All) Mylex EISA 3609A hpda.add

LS (All) Mylex PCI C3610A hpda.add

LX NetRaid mraid.add

LXr Pro8 NetRaid mraid.add

LPr NetRaid mraid.add

LXr 8000 NetRaid mraid.add

LXr 8500 NetRaid mraid.add

(*) Integrated controller.

Table #3

List of embedded Video chip for each NetServer.

NetServer Adapter Name

========= ============

E 30 S3 Trio 64

E 40 Cirrus CL5446 1M

E 45 Cirrus CL5446 1M

E 50 Cirrus CL5446 1M

E 60 ATI Rage IIC 2M

LC Trident 9000I 512K

LC II Cirrus CL5446 1M

LC 3 Cirrus CL5446 1M

LC 2000 ATI Rage IIC 2M

LD Trident 9000i 512K

LD Pro Trident 9000i 512K

LF Trident 9000i 512K

LH Trident 9000i 512K

LH Pro Trident 9000i 512K

LH II Trident 9000i 512K

LH 3 Cirrus CL5446 1M

LH 4 Cirrus CL5446 1M

LH 3000 ATI Rage IIC 2M

LM (All) Western Digital 512K

LS (All) Cirrus 5436 512K

LX Cirrus 5436 512K

LXr Pro8 S3 Virge

LPr Cirrus CL5446 1M

LXr8000 CL5446 1M

LXr8500 CL5446 1M

Note: Video adapters with 1M can be upgraded to 2M.

Table #4

This table provides a list of CD-ROM type for each NetServer

CD-ROM

NetServer Type

========= ======

E 30 IDE

E 40 IDE

E 45 IDE

E 50 IDE

E 60 IDE

LC SCSI

LC Plus SCSI

LC II IIDE

LC 3 IDE

LC 2000 IDE

LD SCSI

LD Pro SCSI

LF SCSI

LH SCSI

LH Pro SCSI

LH II SCSI

LH 3 IDE

LH 4 IDE

LH 3000 IDE

LM (All) SCSI

LS (All) SCSI

LX SCSI

LXr Pro8 IDE

LPr IDE

LXr 8000 IDE

LXr 8500 IDE

Altri manuali per D7171A - NetServer - LPr

117

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali HP Scrivania

HP S3240 Manuale utente

HP Pavilion w1100 - Desktop PC Manuale operativo

HP ProDesk 400 G5 Manuale

HP Vectra VL6 7 Manuale utente

HP TouchSmart 610 PC Manuale utente

HP ProDesk 480 G3 MT Manuale

HP Envy Recline23 TouchSmart Beats SE... Istruzioni per l'installazione

HP Pavilion t100 - Desktop PC Manuale utente

HP SR5605F - Compaq Presario - 1 GB RAM Manuale di istruzioni

HP Pavilion t152 Manuale utente

HP Rp5700 - Point of Sale System Guida all'installazione

HP i2000 Manuale utente

HP TouchSmart IQ700 - Desktop PC Istruzioni per l'installazione

HP Media Center Manuale utente

HP dx7500 - Microtower PC Manuale utente

HP Compaq Presario Manuale

HP Compaq dx2080 Microtower Istruzioni utente

HP Presario SR1300 - Desktop PC Manuale di istruzioni

HP Compaq dc7600 MT Manuale

HP Pavilion k200 - Desktop PC Istruzioni per l'installazione

HP TouchSmart IQ804 Manuale utente

HP 79XXY Manuale utente

HP s7600n - Pavilion Media Center Manuale utente

HP Omni Pro 110 Istruzioni utente

Manuali Scrivania popolari di altre marche

Asus

Asus E210 Series Manuale utente

Dell

Dell Inspiron 600m Manuale utente

Dell

Dell Inspiron 3662 Manuale utente

TotalFlow

TotalFlow uFLO Manuale utente

Logitech

Logitech MK320 Manuale utente

Dell

Dell XPS 730 H2C Manuale utente

Sony

Sony Vaio Series Manuale utente

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuale utente

Alto

Alto MD 250 Manuale utente

Lenovo

Lenovo ThinkCentre Edge 72 Manuale

Lenovo

Lenovo ThinkStation D20 Manuale

Arbor Technology

Arbor Technology FPC-7800 Series Manuale utente

Sony

Sony VAIO VGX-TP1 Series Manuale utente

Asus

Asus Eee Box B204 Manuale utente

Dell

Dell Optiplex 9010 All In One Manuale utente

Everex

Everex eXplora Manuale utente

Lenovo

Lenovo ThinkCentre M75e Manuale utente

Dell

Dell Alienware Area-51 R4 Manuale utente