HP StorageWorks 2/16 - SAN Switch Manuale utente

addendum

Printed in the U.S.A. March 2003

Product names mentioned herein may be trademarks of their respective companies as reflected by an associated

footnote. The information in this document is subject to change without notice.

This addendum only applies to the following documents:

HP StorageWorks SAN Switch 2/32 Installation Guide, Version 4.0.x

AA–RTQVB–TE (February 2003)

HP StorageWorks SAN Switch 2/16 Installation Guide, Version 3.0.x

AA–RR84B–TE (February 2003)

HP StorageWorks SAN Switch 2/8 Installation Guide, Version 3.0.x

AA–RSB6B–TE (February 2003)

hp StorageWorks

SAN switch universal rack mount

kit installation

Product Version: V3.0.x/V4.0.x

Pen-and-ink Changes

2 SAN Switch Universal Rack Mount Kit Installation Addendum

This addendum consists two parts:

■Pen-and-ink Changes—provides instructions for locating specific text and

either deleting text, replacing text with new text, or adding new text at a

specific location.

■Page Additions—identifies where to add a page at a specific place in the

document and recommends how to attach the replacement pages.

Note: If the changes within this addendum are not incorporated into the specified

documents and then used, problems might arise from using obsolete information.

Pen-and-ink Changes

There are no pen-and-ink changes in this addendum.

Page Additions

The following pages describe the installation of the SAN Switch 2/32, SAN

Switch 2/16, and SAN Switch 2/8 in an HP Series 9000 or comparable EIA rack,

or in an HP System/e rack using the SAN Switch Universal Rack Mount Kit, part

number 331148-B21.

For each document, insert the following sheets as shown here:

1. After page 30 in the HP StorageWorks SAN Switch 2/32 Installation Guide

2. After page 29 in the HP StorageWorks SAN Switch 2/16 Installation Guide

3. After page 32 in the HP StorageWorks SAN Switch 2/8 Installation Guide

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

Installing the Switch in a Rack Using the SAN Switch Universal

Rack Mount Kit

This section provides instructions for installing the SAN Switch 2/32, SAN

Switch 2/16, or SAN Switch 2/8 in an HP System/e rack, or in an HP 9000 Series

or comparable EIA rack using the SAN Switch Universal Rack Mount Kit, part

number 331148-B21.

Figure 1: SAN Switch 2/16 rack-mounted switch

Note: The Universal Rack Mount Kit installation requires two technicians.

The following items are required to install the switch in a rack:

■SAN Switch 2/32, SAN Switch 2/16, or SAN Switch 2/8

■Power cables

■#2 Phillips screwdriver

■7/16-inch wrench or socket

■The SAN Switch Universal Rack Mount Kit rails and rail mounting hardware

listed below:

(2) Rear mounting brackets

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

A right inner rail and a right outer rail

A left inner rail and a left outer rail

(14) #8-32 x 3/16-inch Phillips pan-head screw with captive

star lock washer

(10) #10-32 x 1/2-inch Phillips pan-head screw with captive

star lock washer

(8) #10 alignment washer

(8) #10 adapter washer

(2) 1/4-20 hex nut with captive star lock washer

(2) 1/4-inch flat washer

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

Caution: For proper airflow, the SFP media side of the SAN Switch 2/32,

SAN Switch 2/16, or SAN Switch 2/8 must face the rear of the rack. This

mounting allows air to enter from the front of the rack and to exhaust at the

rear of the rack, similar to other rack-mounted equipment. This prevents switch

overheating, which may cause it to fail.

To install the switch in a rack:

1. Check contents of the shipping carton to verify all the required parts and

hardware are available.

2. Choose a mounting location in the rack for the switch.

3. Attach the rear mounting brackets to the rear rack uprights by completing one

of the following steps:

— For an HP 9000 Series or comparable EIA rack, assemble each of the two

brackets with (2) #10-32 x 1/2-inch Phillips pan-head screws with captive

star lock washers and (2) #10 adapter washers as shown in Figure 2.

Figure 2: Installing the rear mounting brackets (HP 9000 Series or comparable EIA

rack)

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

— For an HP System/e rack, install each of the two rear mounting brackets

with (2) #10-32 x 1/2-inch Phillips pan-head screws and (2) #10

alignment washers as shown in Figure 3.

Figure 3: Installing the rear mounting brackets (HP System/e rack-left rear upright)

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

Note: This kit contains both left rails and right rails. The rails are marked with

Right

and

Left

to distinguish the rails from each other.

4. Assemble the outer rails by completing the following steps:

a. Attach the left outer rail and the right outer rails to the rear mounting

brackets using (2) 1/4-20 hex nuts with captive star lock washers attached

loosely as shown in Figure 4. Don’t tighten them. The nuts will be

tightened later in step 8.

Figure 4: Installing the outer rails (HP 9000 Series or comparable EIA rack)

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

b. Depending on the rack you are using, complete one of the following tasks:

— For an HP 9000 Series or comparable EIA rack, install two #10-32 x

1/2-inch Phillips pan-head screws with captive star lock washers and two

#10 adapter washers in the upper and lower hole locations of the right rail.

Then install two #10-32 x 1/2-inch Phillips pan-head screws with captive

star lock washers and two #10 adapter washers in the upper and lower

hole locations of the left rail. See Figure 5.

Figure 5: Assembling the outer rails (HP 9000 Series or comparable EIA rack)

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

— For an HP System/e rack, install two #10-32 x 1/2-inch Phillips pan-head

screws with captive star lock washers and two #10 alignment washers in

the upper and lower hole locations of the right rail. Then install two

#10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers

and two #10 alignment washers in the upper and lower hole locations of

the left rail. See Figure 6.

Figure 6: Assembling the outer rails (HP System/e rack)

5. Determine the number of #8-32 x 3/16-inch Phillips pan-head screws with

captive star lock washers required to assemble the inner rails by referring to

Table 1.

Table 1: Number of screws required to assemble the inner rails

Switch

Number of #8-32 x 3/16-inch

Screws

SAN Switch 2/32 12

SAN Switch 2/16 10

SAN Switch 2/8 14

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

6. For the SAN Switch 2/32 and SAN Switch 2/16, perform step a. For the SAN

Switch 2/8, perform step b.

Caution: Do not use any other screws other than the fourteen that are

provided. Use of any longer lengths can cause damage to internal components

Note: The inner rails work for all three SAN switches—SAN Switch 2/32, SAN Switch

2/16, and SAN Switch 2/8. The mounting holes in the inner rails are marked with 32,

16, and 8. Use the appropriately labeled mounting holes when installing the inner rails

on a switch. For example, to install the inner rails on the SAN Switch 2/32, use the

mounting holes labeled with 32.

When viewing a rack from the front, the left rails are used in the left side of the rack and

the right rails are used in the right side of the rack. The rails must match up—right inner

with right outer and left inner with left outer. Note that the SAN switch mounts in the

rack with its front, the port side, facing the back of the rack. The rear of the switch, the

AC side, faces the front of the rack.

Altri manuali per StorageWorks 2/16 - SAN Switch

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali HP Interruttore

HP 480-0005-00-15 Manuale utente

HP ProCurve 8200zl Manuale utente

HP 316095-B21 - StorageWorks Edge Switch 2/24 Manuale di istruzioni

HP OfficeConnect 1820 8G Manuale utente

HP A7533A - Brocade 4Gb SAN Switch Base Manuale di istruzioni

HP 5600-48XG-4QSFP+ series Manuale utente

HP 5120 EI Series Manuale utente

HP StorageWorks 1606 - Extension SAN Switch Manuale operativo e di manutenzione

HP StorageWorks Brocade Manuale utente

HP 377707-002 Manuale utente

HP ProCurve 8212zl Series Manuale utente

HP 6125XLG Manuale utente

HP A3100-16 DC EI Manuale utente

HP 3500 Series Manuale utente

HP AK241A - StorageWorks 8Gb Simple SAN... Manuale utente

HP FlexFabric 12900 series Manuale utente

HP 6125G Manuale di installazione

HP 6125XLG Manuale di installazione

HP FlexFabric 12900E series Manuale utente

HP J9979A Manuale utente

HP ProCurve 1600M Manuale utente

HP ProCurve 5406zl Manuale utente

HP J9827A Manuale utente

HP OfficeConnect 1820 24G PoE+ Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente