HP Vectra 525 Manuale utente
HP 525 Wireless Dual-Radio 802.11ac
A
ccess Point
Installation Guide
Part number: 5998-5702
Document version: 5W100-20140820
Legal and notice information
© Copyright 2014 Hewlett-Packard Development Company, L.P.
No part of this documentation may be reproduced or transmitted in any form or by any means without
prior written consent of Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS
MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained
herein or for incidental or consequential damages in connection with the furnishing, performance, or use
of this material.
The only warranties for HP products and services are set forth in the express warranty statements
accompanying such products and services. Nothing herein should be construed as constituting an
additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
i
Contents
Preparing for installation ············································································································································· 1
Safety recommendations ··················································································································································1
General safety recommendations···························································································································1
Checking the installation site ···········································································································································1
Accessories provided with the AP ···································································································································2
Installation preparation checklist ·····································································································································2
Installing the AP···························································································································································· 3
Mounting the AP on a wall ··············································································································································3
Mounting the AP to a T-rail ··············································································································································6
Mounting the AP on a ceiling··········································································································································9
Connecting the power supply······································································································································· 10
Connecting the AP to a local power supply······································································································· 10
Connecting the AP to a PoE power supply········································································································· 11
Connecting the AP to the network································································································································ 11
Support and other resources ·····································································································································13
Contacting HP ································································································································································ 13
Subscription service ·············································································································································· 13
Related information························································································································································ 13
Documents······························································································································································ 13
Websites································································································································································· 13
Conventions ···································································································································································· 14
Appendix A Chassis views and technical specifications ························································································16
Chassis views ································································································································································· 16
Weights and dimensions······································································································································ 17
Power consumption ··············································································································································· 17
Power specifications ······················································································································································ 18
AC voltage range·················································································································································· 18
Power adapter specifications······························································································································· 18
Storage media and memory specifications················································································································· 18
Appendix B LEDs························································································································································19
Appendix C Built-in antenna ·····································································································································20
Index ···········································································································································································23
1
Preparing for installation
IMPORTANT:
This installation guide shows you how to install and get started using the HP 525 Wireless Dual-Radio
802.11ac Access Point JG993A(AM), JG994A(WW), JG995A(JP), JG996A(IL), JG997A(8pack AM),
J
G998A(8pack WW), hereafter referred to as the HP 525..
Safety recommendations
W
ARNING!
•This product is designed for specific application and needs to be installed by someone with RF and
related rule knowledge. The general user shall not attempt to install or change the setting.
•Before installation and operation, read all of the safety instructions in
Compliance and Safety Guide
supplied with your AP.
General safety recommendations
To avoid possible bodily injury or equipment damage, read the following safety recommendations
before you install an HP 525. The recommendations do not cover every possible hazardous condition.
•Make sure the ground is dry and flat and anti-slip measures are in place.
•Keep the chassis clean and dust-free.
•Do not place the AP in a moist area and avoid liquid surrounding the AP.
•Keep the chassis and installation tools away from walkways.
Checking the installation site
W
ARNING!
Please carefully select the installation position and make sure the final output power does not exceed the
limit set forth in relevant rules. The violation of the rule could lead to serious federal penalty.
Determine the installation position by observing the following principles:
•To meet regulatory RF exposure requirements, install the device at a location where the radiating
antenna can be kept 40 cm (15.75 in) from any person.
•Leave as few obstacles (such as wall) as possible between APs and clients.
•Install APs away from electronic devices (such as microwave ovens) that might generate radio
frequency (RF) noise.
•Do not install APs in a place where water seeping, water soaking, and condensing occur. Prevent
water or moisture from entering the APs.
2
•Do not place the device on any metal surface. Place it where there are no obstacles and good
signal strength is available.
Accessories provided with the AP
W
ARNING!
Only use the antennas which have been approved by the applicant. Unapproved antenna(s) may produce
unwanted spurious or excessive RF transmitting power, which is prohibited and could be in violation of
FCC/IC limits.
Wall-mounting bracket T-rail holder
×2
MAC address label T-rail holder mounting screw
×3
×3
Wall anchor kit Hex-head bolt, washer, and nut
Antennas, power adapter, and power cable are user-supplied.
Installation preparation checklist
Before you install an AP, verify the following items:
•Connect the power cord and connect the AP to the network. Examine the LED status to make sure
the AP can operate correctly. For more information about AP LEDs, see "Appendix B LEDs."
•Verify that cabling has been completed.
•The device supports 802.3af-compliant PoE. To achieve the best performance, HP recommends that
you use a GE connection to the power device.
•Record the MAC address and serial number of the AP (marked on the rear of the AP) for future use.
•If part of the power line is routed outdoors, use a power strip with lightning protection (user supplied)
to connect the power cord of the AP to the power line.
3
Installing the AP
Figure 1 Installation flowchart
The device can only be used indoors and has built-in antennas. When you install the AP, determine
whether external antennas are needed. External antennas are not included with the AP and this
document does not include external antenna installation procedures.
Mounting the AP on a wall
IMPORTANT:
Connect the AP to the network by using an Ethernet cable, and then install the AP to the wall-mounting
bracket.
To mount the AP on a wall, use the wall-mounting bracket and wall anchor kit that is supplied with the AP
as shown in Figure 2.
Start
Determine the installation position Mount the AP to a wall
End
Check before
installation
Install the wall-
mounting bracket
Ceiling mounting
Attach the T-rail
holder to the T-rail
Install the AP
Connect the power
supply
Connect the AP to
the network
Mount the wall-
mounting bracket to
the ceiling
T-rail mounting Mount the AP on a ceiling
Attach the wall-
mounting bracket to
the T-rail holder
4
Figure 2 Screw hole locations and sizes (in mm)
(1) Hook (2)
Mountin
g
hole
(3) Clip (4)
Mountin
g
clip
To mount the AP on a wall:
1. Use the wall-mounting bracket as a template to mark the locations of the mounting holes on the
bracket. Drill three 5 mm (0.2 in) diameter holes on the marked mounting hole locations as shown
in Figure 3.
Figure 3 Drilling holes in the wall
Ø5.0
86.0
136.0
12
4
3
40 mm
86 mm
5
2. Insert a wall anchor into each mounting hole, and tap the wall anchor with a rubber hammer until
it is flush with the wall surface as shown in Figure 4.
Figure 4 Inserting a wall anchor
3. Align the holes in the wall-mounting bracket with the anchors and insert screws through the
installation holes into the wall anchors as shown in Figure 5.
4. Adjust the position of the wall-mounting bracket and tighten the screws.
Figure 5 Installing the wall-mounting bracket
(1) Wall-mountin
g
bracket (2) Hook
(3) Clip (4) Screw, Length ( 17.4mm / 0.69in ), Wrench
size ( 6.5mm / 0.26in ), Thread size ( 3.5mm
/
0.14in )
5. Connect the AP to the network by using an Ethernet cable.
6. Align the mounting keyhole on the rear of the AP over the hook on the wall-mounting bracket.
See Figure 6.
123
4
6
7. Mount the AP on the hook on the wall-mounting bracket. See callout 1 in Figure 6.
8. Pull down the AP until it clicks into place. See callout 2 in Figure 6.
Figure 6 Mounting the AP to the wall mounting bracket
Mounting the AP to a T-rail
IMPORTANT:
The width of the T-rail must be in the range of 16 mm to 28 mm (0.63 in to 1.10 in).
7
Figure 7 Screw hole locations and sizes (in mm)
(1) Hook (2) Mountin
g
hole
(3) Clip
(4) Mountin
g
clip
Figure 8 T-rail holder
(1) T-rail clip (2)
M3 screw nut
(3) M4 screw nut (4)
Clip holder
(5) T-rail holder (6) Mounting hook
(7) M4 × 5 screw, Length ( 7.6mm / 0.3in ), Wrench
size ( 7mm / 0.28in ), Thread size ( 4mm / 0.16in )
(8) M3 × 8 screw, Length ( 10mm / 0.39in ), Wrench
size
( 5.5mm / 0.22in ),
Thread
size
( 3 mm / 0.12in )
To mount the AP to a ceiling T-rail:
1. Loosen the two M3 × 8 screws on each clip holder. Do not remove the screws.
2. Adjust the T-rail clips to make the T-rail holder wider than the T-rail. See callout 1 in Figure 9. Then
lock the T-rail with the T-rail holder according to the arrow indicated in callout 2 in Figure 9.
Ø5.0
86.0
136.0
12
4
3
Altri manuali per Vectra 525
1
Indice
Altri manuali HP Punto di accesso wireless
HP
HP MSM310-R Manuale utente
HP
HP MSM313 Manuale utente
HP
HP 527 Manuale utente
HP
HP msm4 series Manuale utente
HP
HP Aruba 570 Series Manuale utente
HP
HP WL520 Manuale utente
HP
HP Compaq Presario,Presario 650 Manuale utente
HP
HP ProCurve 520wl Istruzioni per il montaggio
HP
HP MSM410 Manuale utente
HP
HP MSM-802.11n Istruzioni utente
HP
HP DESKJET 350 Manuale utente
HP
HP MSM310 Manuale utente
HP
HP MSM3xx Manuale utente
HP
HP E-MSM460 Istruzioni per il montaggio
HP
HP ProCurve 420 Manuale utente
HP
HP 600R Series Manuale utente
HP
HP V-M200 Manuale utente
HP
HP P1981A Manuale utente
HP
HP MSM335 Manuale utente
HP
HP Aruba AP-587 Istruzioni per l'installazione
