Huawei BBU3900 V300 Manuale utente
HUAWEI TECHNOLOGIES Co., Ltd.
BBU3900
V300
Installation Guide
Issue: 16
Date: 2010-07-30
1
Contents
Installation Tools…………………………………
Installation Scenarios……………………………
BBU Hardware……………………………………
Installation Procedure……………………………
Installing the BBU in the APM30………………
Installing the BBU in the APM30H(Ver.A) ……
Installing the BBU in the 19-Inch Rack…………
Installing the BBU in the TMC……………………
Installing the BBU in the PS4890 Cabinet……
Installing the BBU in the RRU3004 Rack………
Installing the IMB03 on the H-Shaped Stand…
Installing the RRU on the H-Shaped Stand …
Installing the BBU on the Wall…………………
Installing the BBU in the APM30H(Ver.B)……
Installing the BBU in the TMC11H(Ver.B)……
Installing the BBU in the
APM30H(Ver.B, +24V) ……………………………
Installing the BBU in the OMB …………………
BBU Hardware Installation Checklist…………
Powering On the BBU……………………………
Appendix……………………………………………
Obtaining the ESN ………………………………
Change History……………………………………
2
3
5
6
7
13
15
17
20
23
27
28
29
33
37
39
41
47
47
48
48
56
Copyright © Huawei Technologies Co., Ltd. 2010. All rights reserved.
2
Installation Tools
Measuring tape Phillips screwdriver (M3-M6) Flat-head screwdriver (M3-M6)
Adjustable wrench Socket wrench Hammer drill
ESD wrist strap Vacuum cleaner Wire stripper
Torque wrench Marking pen Level
RJ-45 crimping tool Multimeter
Power cable crimping tool Cable cutter ESD gloves
Rubber Mallet
3
Installation Scenarios
In the APM30/APM30H(Ver.A) In the PS4890
In the RRU3004 rackIn the TMC
In the 19-inch rack
The GTMU in this document is based on the first type of GTMU.
In the APM30H(Ver.B)
4
Installation Scenarios
In the TMC11H(Ver.B) In the APM30H (Ver.B, +24V)
On the wall In the OMB
5
BBU Hardware
1. Exterior of the BBU
2. Configuration Principles of the BBU Boards
Preferentially installed in the slot4.S0 or S41OptionalUTRP
A single UELP is preferentially configured
in the S4 slot.
S0 or S42OptionalUFLP
Preferentially installed in the S1 slot.S0 or S11OptionalUSCU
Preferentially installed in the S18 slot.S181OptionalUEIU
A single UELP is preferentially configured
in the S4 slot.
S0 or S42OptionalUELP
Can be installed only in the S16 slot.S161MandatoryFAN
A single UPEU is preferentially configured
in the S19 slot.
S18 or S192MandatoryUPEU
Can be installed only in S5 and S6.S5 and S61MandatoryGTMU
RemarksInstallation
Slot
Full ConfigurationMandatory/
Optional
Board
zThe UELP and UFLP need to be optionally configured in the BBU or SLPU on site according to the field
requirements.
zUTRP is supported in V300R012 and later versions.
86 mm
(2U)
442mm
310mm
6
Installation Procedure
When the equipment is unpacked, it must be powered on in 24 hours. The maximum duration
of the power-off state of the equipment is 24 hours during maintenance.
7
Installing the BBU Case
a
Installing the BBU Cables
b
External power supply
External alarm device
Monitoring signal
cable
Alarm cable
E1/T1cable
CPRI signal cable
E1/T1 surge protection
transfer cable
Power cable
Cable connections of the BBU
External monitoring device
Installing the BBU in the APM30
BBU
M6 bolt
PDU
1. Install the mounting ears at both sides of
the BBU reversely.
2. Slide the BBU case into the cabinet.
FE/GE cable
FE/GE surge protection
transfer cable
8
Installing the BBU in the APM30
Winding pipe
Installing the BBU Cables
b
2. Install the CPRI optical cable.
Connect the fiber tails labeled 2A and 2B to one of the CPRI0 to CPRI5 ports on the
GTMU, and connect the fiber tails labeled 1A and 1B to the CPRI_W port on the RRU.
The TX port on the BBU is connected to the RX port on the RRU.
The RX port on the BBU is connected to the TX port on the RRU.
Connect the OT terminal of the power cable to the LOAD3
terminal of the PDU, and then fix the 3V3 connector of the
power cable to the PWR port on the BBU.
1. Install BBU power cable.
The OT terminals of the power cable is to be made on site.
Optical module
Puller
a. Insert the optical module into the CPRI0,
CPRI1, CPRI2 CPRI3, CPRI4 or
CPRI5 port, and then turn outwards
the puller on the optical module.
b. Insert one end of the CPRI optical cable
into the optical module, and then lead
the CPRI optical cable out of the
cabinet along the right side of the
cabinet.
c. Wrap the fiber tail with the winding pipe.
LOAD3
NEG(-)
RNT(+)
PWR
The single-mode optical module is
labeled "SM" and multi-mode optical
module is labeled "MM".
9
Installing the BBU in the APM30
b
4.3. Strip the jacket off the E1/T1 cable near the grounding point at the lower right
corner of the cabinet to expose the shielding layer
4.4. Thread the E1/T1 cable through the grounding clip. Then, tighten the screw on the
grounding clip to make the shielding layer of the E1/T1 cable in full contact with the
grounding clip. Finally, connect the PGND cable on the grounding clip to the ground bolt
of the APM30.
4.2. Fix the DB26 connector of the E1/T1 cable to the OUTSIDE port on the UELP.
3. Install the E1/T1 surge protection transfer cable.
4. Install the E1/T1 cable.
E1/T1 surge protection
transfer cable
4.1. Cabling the E1/T1 cable.
E1/T1cable
Shielding layer of
the E1/T1 cable
Shielding layer of the E1/T1
cable (25 mm)
Fix the DB25 connector of the E1/T1 surge protection transfer cable to the INSIDE
port on the UELP and the DB26 connector to the E1/T1 port on the GTMU.
Grounding
clip
Installing the BBU Cables
Before soldering the connectors to the E1/T1 cable, ensure that both ends of the E1 cable are
disconnected from any devices. In addition, all the connectors should be soldered to the cable.
Indice
Altri manuali Huawei Hardware di rete
Huawei
Huawei RT-FIC-1T1-V2 Manuale utente
Huawei
Huawei eSpace IAD104H Manuale utente
Huawei
Huawei VCN520 Manuale utente
Huawei
Huawei XMC-1 ODU Manuale utente
Huawei
Huawei SUN2000-15KTL-50KTL Series Manuale utente
Huawei
Huawei FusionModule2000-S Manuale utente
Huawei
Huawei PDU8000 Series Manuale utente
Huawei
Huawei RT-NE20E-RPU-512M Manuale utente
Huawei
Huawei RT-FIC-16LS Manuale utente
Huawei
Huawei MA5200F-2000 Manuale utente
Huawei
Huawei NE-HIC-2xFE Manuale utente
Huawei
Huawei OptiX OSN 9560 Manuale utente
Huawei
Huawei eAN3810A Guida di riferimento rapido
Huawei
Huawei BBU3900 Manuale utente
Huawei
Huawei HW-TX-5000 Manuale utente
Huawei
Huawei CR-P4CF Manuale utente
Huawei
Huawei CR52-MPUA Manuale utente
Huawei
Huawei CR52-SRUA Manuale utente
Huawei
Huawei FIC-1E1 Manuale utente
Huawei
Huawei RT-16ASE Manuale utente
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
