Humanscale M2.1 Manuale utente

Desk Mount

Assembly Instructions

North America: +1 800 400 0625

Europe: +353 (0)1 858 0910

Asia Pacic: +852 2581 0570

EN 1 - 8

FR 9 - 16

ES 17 - 24

PT 25 - 32

4 Standard VESA Bracket

Screws

4 Plastic Spacers

4 Extended VESA Bracket

Screws

VESA Bracket and Cover

4mm Hex Key

Bolt-Through Plate

Sliding Desk Mount

Clamp Mount

8mm Hex Key Bolt-Through Bolts

Bolt-Through Mount

NOTE: 4mm Hex Key can be found

under the plastic base cover.

INSTALLATION HARDWARE

STEP 1: ATTACH MOUNTTO WORK SURFACE

CLAMP MOUNT

NOTE: There are two sets of Bracket Screw holes to

accommodate the thickness of every work surface. Use the

upper holes for surfaces up to 1.8” (48mm) thick and lower

holes for surfaces up to 2.7” (68mm) thick.

A - For installation on open edge of work surface:

1. Slide Mount (A) against work surface edge and fully tighten

Clamp screws(B) with 4mm hex key (C).

B - For installation on work surface positioned against a

wall or panel:

NOTE: This method can also be used to mount through

grommet holes wider than 3”

1. Detach the Bottom Clamp (D) from the Top Bracket (E) by

loosening Bracket Screws (F) with 5mm hex key.

2. Position the Top Bracket against work surface edge.

3. Underneath the work surface, reattach the Bottom Clamp

to the Top Bracket using the Bracket screws.

4. Fully tighten the Clamp Screws (G) with 5mm hex key.

NOTE: Clamp Mounts cannot be used to mount the M2.1 to

any vertical surface.

SLIDING DESK MOUNT

1. Remove Base Cover.

2. Loosely attach Sliding Desk Clamp (H) to base with three

included screws (I).The screws should not be tightened all

the way.

3. Slide the base and clamp over the back edge of the work

surface until the clamp rests on the edge.

4. Fully tighten the three clamp screws to secure the base to

the work surface.

BOLT-THROUGH MOUNT

1. Drill 1/2” hole through work surface in desired location.

NOTE: Bolt-Through Mount can accommodate a hole up to 4” (102mm)

in diameter. If hole is 2” (51mm) or more, cables can be routed through

the hole. For some 2” grommet holes, cables should be routed before

installation of mount to accommodate cable plugs (cable access is

approximately 1.5” x 0.25” with 2” grommets).

2. Position the M2.1 Base over the work surface hole (J).

3. Align Bolt-Through Plate (K), foam side up, under the work surface.

Pass the Bolt (L) through the hole in the plate and screw into M2.1

base by using 8mm hex key.

In each arm connection, there is an adjustable Smart Stop Ring which can be

positioned to limit the arm’s range of motion. Depending on the orientation of the

ring the arms can be set to rotate either 90°, 180° or 360°. The marked angle will

be in the center of the range of motion. The stop rings must be congured in such

a way that the dynamic link head does not pass behind the rear edge of the unit.

Arm can rotate

without stopping

Arm can rotate 180˚

Arm can rotate 90˚

STEP 2: SMART STOP ADJUSTMENT

NOTE: Before adding each link, adjust the smart

stop (A) according to step 2. If using a 3 link

conguration, one of the links must be a 4”

link. The link installation order may need to be

swapped so as to comply with step 2.

1. Insert the angled link into the mount until release

button locks in place.

2. Insert the dynamic link into the angled link until

the release button locks in place.

3. To remove links, press the release button (B) and

lift upward near the joint.

1. Separate the VESA cover from the VESA bracket.

2. Position the VESA Bracket over the mounting holes on the back of

monitor with the D-shaped cutouts in a vertical orientation. Attach

using the 4 VESA screws provided.

3. Snap the VESA cover back in place.

NOTE: The VESA Bracket features 75mm and 100mm hole patterns.

If you need to offset the Bracket from the monitor use the provided

Extended VESA Screws and Plastic Spacers. You may also use the

screws that came with your monitor.

STEP 3: ATTACH ARMTO BASE STEM

STEP 4: ATTACH VESA BRACKETTO MONITOR

1. Hold the monitor angled back and lower it onto

the arm. Fit the hook at the top of the arm into

the corresponding cutout in the VESA Bracket.

2. Tilt the monitor back upright until the Quick

ReleaseTab (B) on the arm snaps into position.

3. To remove the monitor, lift the Quick ReleaseTab

and pull the bottom of the monitor away from

the arm, then lift free of the hook.

NOTE: If needed, adjust the tension screw (A) to

hold the monitor in position.

Your monitor should move up and down easily and stay in

place once adjusted. If it is difcult to adjust or moves without

assistance, it is not properly balanced.

M2.1:Weight Range: 5.5-15.5 lbs. (2.5-7 kg)

1. Press the Upper Arm Link (A) downward until Adjustment

Screw (B) is visible.

2. If the arm rises up on it’s own, the lift force is too high

and can be decreased by rotating the Adjustment Screw

counterclockwise (towards -) with a 4 mm hex key. If the

arm falls down with the weight of the monitor, the lift force

is too low and can be increased by turning the Adjustment

Screw clockwise (towards +).

3. The current counterbalance setting can be seen through the

counterbalance indicator (C) on top of the upper arm. This

information can be used to quickly set multiple arms to the

same level without needing the monitors to be installed.

CAUTION: Do not over tighten the screws as it can damage

the screw head or threads.

STEP 5: ATTACH MONITORTO ARM

STEP 6:WEIGHT ADJUSTMENT

1. Route power and monitor cables through the

exible cable clips on the M8.1’s upper link (A).

NOTE: Leave enough slack in the cables to allow

arms to rotate without difculty.

2. Slide the plastic cover (B) on the lower link

upward to remove.

3. Using the two cutouts (C) as guides, run the

cables over the lower link cover.

4. Lift the cover and cables up to the lower link,

making sure that the cover sits ush with the

surface of the arm.

5. Slide the cover down the arm to lock in place,

then gently pull the cables through the arm to

remove excess slack.

CAUTION: Don’t insert extension cords. Don’t

insert any cord connecting one workstation to

another.

STEP 7: CABLE MANAGEMENT A

For our terms and conditions please go to

https://www.humanscale.com/about/legal-information/terms-conditions.cfm

registered in the United States and certain other countries. The M2.1 trademark is owned by Humanscale Corporation.

humanscale.com

Instructions de montage

dusupport sur bureau

Amérique du Nord: +1800400-0625

Europe: +353(0)18580910

Asie-Pacique: +85225810570

4 vis pour support VESA

standard

4 entretoises en

plastique

4 vis pour support VESA

longues

Support et couvercle

VESA

Clé hexagonale de 4mm

Plaque à boulonner

Support de bureau coulissant

Support de serrage

Clé hexagonale de 8mm Boulons à boulonner

Support avec boulons

REMARQUE: Une clé hexagonale de

4mm se trouve sous le couvercle en

plastique de la base.

MATÉRIEL D’INSTALLATION

Altri manuali per M2.1

Indice

Lingue:

Altri manuali Humanscale Rack e supporto

Humanscale

Humanscale M/FLEX Manuale utente

Humanscale

Humanscale M/Connect 2 MC2-AXY Manuale utente

Humanscale

Humanscale M2.1 Manuale utente

Humanscale

Humanscale M/FLEX Manuale utente

Humanscale

Humanscale V6 Wallstation Istruzioni per l'installazione

Humanscale

Humanscale M/FLEX Manuale utente

Humanscale

Humanscale QuickStand Eco Manuale utente

Humanscale

Humanscale V/Flex Manuale utente

Humanscale

Humanscale UFEA Manuale utente

Humanscale

Humanscale M10 Manuale

Humanscale

Humanscale Mesh Guida alla configurazione

Humanscale

Humanscale QuickStand Eco Manuale utente

Humanscale

Humanscale QuickStand Eco Manuale utente

Humanscale

Humanscale Thin Client Holder Manuale utente

Humanscale

Humanscale Quickstand Manuale utente

Humanscale

Humanscale QuickStand Eco Manuale utente

Humanscale

Humanscale M2.1 Manuale utente

Humanscale

Humanscale M7 Manuale utente

Humanscale

Humanscale Quick Stand Lite Manuale utente

Humanscale

Humanscale V6 Manuale utente

Humanscale

Humanscale M/Connect 2 Manuale utente

Humanscale

Humanscale M/Connect 2 Manuale utente

Humanscale

Humanscale M8.1 Manuale utente

Humanscale

Humanscale QUICKSTAND LITE Manuale utente

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente