HunterDouglas Platinum Manuale d'uso e manutenzione

for PowerRise®

, PowerGlide®

, PowerTilt™and hard-wired systems

Guide

Remote Control

PLATINUM TECHNOLOGY

Control Like Never Before

INDICATOR

LIGHT

CHANNEL

SELECTOR

UP/DOWN

BUTTON

ALL

GROUPS

BUTTON

GROUP 1

BUTTON

GROUP 2

BUTTON

GROUP 3

BUTTON

GROUP 4

BUTTON

Platinum™Technology utilizes both infrared (IR) and radio

frequency (RF) remote control signals. This guide shows

you how to enjoy optimal performance using the two

methods of operation.

The Hunter Douglas Remote Control

BLINKING GREEN =

PROGRAMMING MODE

SOLID GREEN =

GROUP OPERATING

MODE

SOLID RED =

POINT-AND-PRESS

OPERATING MODE

2 hunterdouglas.com

Getting Started

Using the power of Platinum™Technology is easy. In just

two simple steps, your remote is ready.

POWER UP

Remove the battery

compartment cover on

the back of the remote

control. Insert two AAA

alkaline batteries as

diagrammed inside the

battery compartment.

RESET BUTTON

Use a paper clip to press

and quickly release the

MASTER RESET button

located next to the

batteries. Replace the

battery compartment

cover. You are now

ready to begin.

hunterdouglas.com 3

PROGRAM

BUTTON

MASTER

RESET

BUTTON

BATTERY

COMPARTMENT

POINT AND PRESS

Point the remote at the satellite eye.

TILT AND TRAVERSE

Move the channel switch to the left

position (channel 1) to tilt the vane.

Move the channel switch to the right

position (channel 2) to traverse the

window covering.

Point-and-Press Operation

PowerRise®and PowerTilt™operating systems

PowerGlide®operating systems

POINT AND PRESS

Point the remote at the receiver eye (either built into the headrail

or on the satellite eye). Press the UP or DOWN button to operate

the window covering.

TILT TRAVERSE

4 hunterdouglas.com

Programming Groups

hunterdouglas.com 5

BEFORE YOU BEGIN

Partially lower or tilt the

window covering.

PROGRAM BUTTON

Use a paper clip to press

and quickly release the

PROGRAM button on the back

of the remote control. The

indicator light at the top of

the remote will blink green for

approximately 30 seconds.

GROUP NUMBER

While the indicator light

is blinking green, press

the GROUP number to

which you are adding the

window covering.

UP BUTTON

Point the remote at the receiver

eye (either built into the headrail

or on a satellite eye) of the

window covering and press the

UP button. The unit will raise or

“jog” to show that it has been

programmed into the remote

control. Repeat steps to program

other window coverings.

Operating Groups

GROUP NUMBER

Press the GROUP number for

the window covering(s) you

wish to operate.

UP OR DOWN

Press the UP or DOWN

button to operate the window

covering(s) programmed to

that group. The remote does

not need to be pointed at the

receiver eye to operate the

window covering(s).

ALL GROUPS BUTTON

To operate all four groups of

window coverings at the same

time, press the ALL button

before pressing the UP or

DOWN button.

6 hunterdouglas.com

Removing Window Coverings from a Group

hunterdouglas.com 7

BEFORE YOU BEGIN

Partially lower or tilt the

window covering(s).

PROGRAM BUTTON

Use a paper clip to press and

quickly release the PROGRAM

button on the back of the remote

control. The indicator light at the

top of the remote will blink green

for approximately 30 seconds.

GROUP NUMBER

While the light is blinking green,

press the GROUP number from

which you are removing the

window covering.

DOWN BUTTON

Point the remote at the receiver

eye of the window covering and

press the DOWN button. The

unit will lower or “jog” to show

that it has been removed.

MASTER RESET BUTTON

To erase all programmed groups,

use a paper clip to press and

quickly release the MASTER

RESET button located next to

the batteries. Replace the

battery compartment cover.

Notes on Programming

Patented in the U.S. and foreign countries. Other U.S. and foreign patents pending. 5110540027 8/07

ENTERING PROGRAMMING MODE

To activate the programming mode, use a paper clip to press

and quickly release the PROGRAM button located on the back

of the remote control. The programming mode is indicated

by the blinking green indicator light and will stay active for

approximately 30 seconds before timing out.

WINDOW COVERING OPERATION

Window coverings may not be operated while in the programming

mode. Do not operate window coverings when the indicator light

is blinking green.

EXITING PROGRAMMING MODE

To exit the programming mode before it times out, press and

quickly release the PROGRAM button a second time. The indicator

light will stop blinking green. The remote may now be used to

operate your window covering(s).

Refer to the Product Owner’s Guide for further details about

Platinum™Technology.

Indice

Altri manuali HunterDouglas Telecomando

HunterDouglas

HunterDouglas PowerView Manuale utente

HunterDouglas

HunterDouglas PowerView Manuale utente

HunterDouglas

HunterDouglas PowerView Pebble Manuale utente

HunterDouglas

HunterDouglas PowerView Motorization Manuale utente

HunterDouglas

HunterDouglas PowerView Manuale utente

HunterDouglas

HunterDouglas PowerView Pebble Disegno dimensionale

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione