HunterDouglas PowerView Pebble Manuale utente
PowerView
®
Automation
REMOTE CONTROL GUIDE
Your new PowerView®
Pebble®Remote and
Surface Remote combine
fashion with function for
precise control of your
Hunter Douglas window
coverings. Artfully
designed, PowerView
remotes allow you to
control natural light
throughout your home
with the press of a button.
The following pages
provide all the details on
how to set up and operate
both remote styles.
Table of Contents
Key Components. . . . . . . 3
Getting Started. . . . . . . . 9
Programming. . . . . . . . 13
Basic Operation . . . . . .
23
Battery Replacement . . . 27
Troubleshooting . . . . . .
33
Skyline®Gliding Window Panels
Key Components
3
54
POWERVIEW®SURFACE REMOTE
The sleek PowerView®Surface is wall-mounted so you
know your remote is always right where you left it.
KEY COMPONENTS
KEY COMPONENTS
POWERVIEW®PEBBLE®REMOTE
Ergonomically designed, the PowerView®Pebble®
hand-held remote is available in ten on-trend colors
to complement your home décor.
REMOTE MODULE FRONT
RIGHT ARROW
Function varies
with shade type.
LEFT ARROW
Function varies
with shade type.
FAVORITE
Shade/louver
position
STOP
Press and
hold for
programming
mode.
7
GROUP 1
GROUP 2
GROUP 3 GROUP 4
GROUP 5
GROUP 6
6
REMOTE MODULE BACK
CLOSE
OPEN
KEY COMPONENTS
KEY COMPONENTS
PROGRAMMING ACCESS
9
Getting Started
REMOTE MODULE (BACK COVER REMOVED)
BATTERY
COMPARTMENT
3V CR 2032
BATTERY
COMPARTMENT
3V CR 2032
PROGRAMMING
8
KEY COMPONENTS
IMPORTANT: The PowerView®Remote will not operate a
window covering until the window covering has been added
to a GROUP.
Getting started
First, activate the remote by pulling both plastic tabs from the
back battery compartment.
NOTE:If placing the remote module into a Pewter or Clear
Frost Pebble®, ensure the provided color insert is seated at the
bottom of the Pebble cutout.
10
GETTING STARTED
GETTING STARTED
11
Inserting the remote module into the PowerView®Pebble®
(hand-held):
1. Center the Hunter Douglas logo on the remote
module above the indentation on the bottom rim
of the Pebble.
2. Align the ribs on the remote module with the grooves
on the Pebble.
3. Gently push the remote module into the Pebble until
it is snug.
Ribs on remote
to be aligned
with the
grooves on
the Pebble.
Center logo
Programming
1312
GETTING STARTED
Mounting the PowerView®Surface:
1. Choose a location to mount the Surface.
2. Orient the Surface mounting plate so that the HunterDouglas
logo is horizontal and level. Mark screw holes.
3. If you are mounting the Surface onto drywall, use a
7
⁄32" drill bit to drill pilot holes. Tap drywall anchors into
the pilot holes until the flange of the anchor is flush
with the drywall.
4. If you are mounting the Surface onto wood, use a
3⁄32" drill bit to drill the screw holes.
5. Attach the Surface mounting plate using the screws provided.
6. Align the Surface ring with its mounting plate and twist
the Surface ring clockwise to lock it in place.
Inserting the remote module in the Surface:
1. Align the ribs on the remote module with the grooves
on the Surface.
2. Gently push the remote module into the Surface until
it is snug.
Ribs on remote
to be aligned
with the
grooves on
the Surface.
Center logo
IMPORTANT: If you have multiple remotes, please follow
the steps below to pair all remotes to the same PowerView®
Network. If you only have one remote, please refer to page 19
for additional programming steps.
Pairing additional remote(s) to the
PowerView Shade Network
Follow these steps to pair remotes to the same PowerView
Shade Network. All remotes in a home should be paired to
the same network. This allows for easy installation of additional
control options, such as the PowerView Hub and PowerView
Repeaters. To begin the pairing process, select a source remote.
All of the other target remotes will be paired to the source
remote’s network.
1. Locate the programming access on the back cover of
the target remote module.
2. Using a paper clip, press and hold the recessed Pbutton
for 6 seconds.
NOTE: The Group Numbers (1– 6) will flash twice on the
PRESS of the reset button followed by three times at
6 seconds.
3. Press and hold STOP on the source remote, until the
indicator lights blink. The remote is now in programming mode.
4. Press and hold the STOP button on the target remote
while pressing and releasing STOP on the source remote.
5. The backlit GROUP buttons on the target remote will
flash twice to indicate the remote has been paired to the
PowerView Shade Network.
6. Press and hold STOP on the source remote, until the
indicator lights stop blinking to exit programming mode.
15
Pairing PowerView®Repeaters
to a remote created PowerView
Shade Network
Repeaters extend the range of the PowerView®signal emitted
by the PowerView®Pebble®Remote, the PowerView®Surface,
or the PowerView®Hub when used with the PowerView App.
1. PLUG the Repeater into an electrical outlet.
2. Press and hold STOP on the PowerView Pebble
Remote, until the indicator lights blink. The remote
is now in programming mode.
Hold the remote within 3 feet of the Repeater to
complete Step 3.
3. Press STOP on the remote. The Repeater is now
paired to the PowerView Shade Network.
4. Press and hold STOP on the remote, until the
indicator lights stop blinking to exit programming mode.
NOTE: The repeater’s LED will flash, whenever it repeats
a command sent by a device on the same PowerView
Shade Network.
14
PROGRAMMING
PROGRAMMING
Pairing remote(s) to a PowerView
®
Hub
created PowerView Shade Network
A Hub previously paired to an existing remote created
PowerView®Shade Network or that had created its own
network during setup, can have additional Pebble®or Surface
remotes paired to it, even if the remotes are introduced after
the initial Hub setup.
1. Locate the programming access on the back cover of
the remote module.
2. Using a paper clip, press and hold the recessed Pbutton
for 6 seconds.
NOTE: The Group Numbers (1–6) will flash twice on
the PRESS of the Pbutton followed by three times
at 6 seconds.
3. Hold the remote module within approximately
12 inches of the Hub.
Complete Steps 4 and 5 at the same time.
4. Press and hold the STOP button on the remote module.
5. Press and hold the
P
button on the back of the Hub
for approximately three seconds.
NOTE: The Group Numbers (1–6) will flash to indicate
that the remote module has been paired to the
PowerView Shade Network.
17
Creating a duplicate remote
A duplicate remote will operate the same set of window
coverings and GROUPS as the original remote. To begin the
duplicating process, select a source remote that will transfer
its information to the target remote.
1. Locate the programming access on the back cover of
the target remote module.
2. Using a paper clip, press and hold the recessed Pbutton
for 6 seconds.
NOTE: The Group Numbers (1–6) will flash twice on
the PRESS of the Pbutton followed by three times at
6 seconds.
3. Press and hold STOP on the source remote, until
the indicator lights blink. The remote is now in
programming mode.
4. While pressing and holding ALL on the target remote,
press and release STOP on the source remote.
5. The backlit GROUP buttons on the target remote will
flash twice to indicate all of the information from the
source remote has been copied.
6. Press and hold STOP on the source remote, until the
indicator lights stop blinking to exit programming mode.
16
PROGRAMMING
PROGRAMMING
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali HunterDouglas Telecomando
HunterDouglas
HunterDouglas Platinum Manuale d'uso e manutenzione
HunterDouglas
HunterDouglas PowerView Motorization Manuale utente
HunterDouglas
HunterDouglas PowerView Manuale utente
HunterDouglas
HunterDouglas PowerView Manuale utente
HunterDouglas
HunterDouglas PowerView Manuale utente
HunterDouglas
HunterDouglas PowerView Pebble Disegno dimensionale
