Hussmann IMPACT ED1 Manuale utente

JOINING

JOINING KIT

KIT

NOTE: Be sure merchandisers

have been leveled according to

the installation instructions.

Carefully unpack and inspect the

Joining Kit, making sure there is

breakage or damage.

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.)

Service Merchandisers

Joining Instruction

Fresh Meat, Deli and Fish Merchandiser

November, 2000

P/N 0420058 1

PARTS LIST

Item Quantity Description

Nos.

1. 1 Gasket 1/2 x 15/8 x 180

2. 1 Gasket 1/2 x 1/2 x 120

3. 1 Silicone

4. 1 Top Gasket Pad

5. 1 Front Gasket Pad

6. 1 Lighting Rail Joining Bracket

7. 1 Joining Plate

8. 4 Truss Head SM Screw 8 -18 x 3/8

9. 1 Rear Sill Joining Bracket

10. 4 Washer Head Machine Screws 10-24 x 1/2

11. 1 Cap Screw 5/16 -18 x 3/4

12. 2 Flat Washer 5/16

13. 1 Lock Washer 5/16

14. 1 Hex Nut 5/16 - 18

15. 4 Spacer

16. 2 Cap Screw 5/16 - 18 x 31/2

17. 4 FlatWasher 5/16

18. 2 LockWasher 5/16

19. 2 Hex Nut 5/16 - 18

20. 1 Cap Screw 5/16 - 18 x 3

21. 2 Flat Washer 5/16

22. 1 Lock Washer 5/16

23. 1 Hex Nut 5/16 - 18

24. 1 Bottom Joint Cover

25. 1 Splashguard Joint Support

26. 4 Hex Head Sheet metal Screw #8 x 1/2

Front

Rear

Top

DO NOT remove riders until

case is in its final position.

CAUTION

Cross-Members

Screws

(each leg)

Sides

Leg

Screws

(two each end

of each

cross-member)

Shipping Rider

for 8 ft Case

1Remove items below:

Shelves if installed,

Display Pans,

Rear Pan Bracket,

D.Rear Panel and

Discharge Grille

E.Front Return Air Grille

fromcase.

SSeeeeFFiigguurree11..

HUSSMANN CORPORATION •BRIDGETON, MO 63044-2483 (Printed in U.S.A.)

Merchandisers

Fig. 1. Removing items from case

P/N 0420058

2Apply 1 5/8in. (321 mm)

Gasket (Item – 1) to rear

foam panel of both cases as

shown. Check to be sure that

there are no gaps between

gasket and merchandiser.

Note: THIS IS THE ONLY GASKET

THAT IS APPLIED TO BOTH CASES.

THE FOLLOWING STEPS MUST BE

DONE TO ONE CASE ONLY.

See Figure 3. Detail A. & B.

HUSSMANN CORPORATION •BRIDGETON, MO 63044-2483 (Printed in U.S.A.) 3

Fig. 3. Applying 1 5/8 in. Gasket to the Merchandiser

Fig. 2. Checking Alignment Pin and Light Rail Joining Bkt

Impact Service Merchandisers Joining Instruction

P/N 0420058

Apply 1 5/8 in. (321 mm) gasket to both cases

Gasket

Make sure the alignment pins and Light Rail Joining Bracket

are in place before gasketing and sealing cases. See Figure 2.

IMPORTANT

Gasketing and Sealing Procedure:

Light Rail

Joining Bracket

Alignment Pins

DETAIL A.

DETAIL B.

3Apply 1/2in. (13 mm) Gasket

(Item – 2) to the horizontal

recess across the bottom.

•Do not stretch gasket, espe-

cially around corners.

•Do not butt gaskets; always

overlap them as shown.

•Remove paper backing after

gasket has been applied.

SSeeeeFFiigguurree44,,DDeettaaiillCC..

HUSSMANN CORPORATION •BRIDGETON, MO 63044-2483 (Printed in U.S.A.)

Apply 1/2 in. (13 mm ) gasket

Fig. 4. Applying 1/2 in. Gasket

Merchandisers

DETAIL C.

P/N 0420058

HUSSMANN CORPORATION •BRIDGETON, MO 63044-2483 (Printed in U.S.A.)

4Before joining, make sure and

lay a 1/2inch bead of clear

Silicone (Item – 3) along the

entire perimeter of the case as

shown in FFiigguurree55..

5In addition, apply silicone

around the perimeter of the

front joining hole and over the

top of the frame. SSeeeeFFiigguurree

55,,DDeettaaiillssDDand EE..

Alignment

Pins

Silicone

Here

Fig. 5. Applying Silicone

DETAIL E.

DETAIL D.

Impact Service Merchandisers Joining Instruction

P/N 0420058

6Install the Top Gasket Pad,

(Item – 4). SSeeeeFFiigguurree66,,

DDeettaaiillFF..

7Install the Front Gasket Pad,

(Item – 5). SSeeeeFFiigguurree66,,

DDeettaaiillGG..

8Apply Silicone onto the Top

Gasket Pad (Item – 4) and the

Front Gasket Pad (Item – 5).

SSeeeeDDeettaaiillssH - a..and H - b..

HUSSMANN CORPORATION •BRIDGETON, MO 63044-2483 (Printed in U.S.A.)

1/2 (13 mm) X 1/2 (13 mm)

1/2 (13 mm) X 1 5/8 in. (41 mm)

Top Gasket Pad

Front Gasket Pad

Merchandisers

Silicone

Front

Gasket

Pad 5

Fig. 6. ApplyingTop and Front Gasket Pads

Top

Gasket

Pad

DETAIL H-b.

DETAIL F.

DETAIL G.

P/N 0420058

DETAIL H-a.

Silicone 3

HUSSMANN CORPORATION •BRIDGETON, MO 63044-2483 (Printed in U.S.A.) 7

Fig. 7. Leveling Merchandisers

9Move the second merchandiser

into position against the first.

Match the alignment pins

with the corresponding holes.

SSeeeeFFiigguurree77,,DDeettaaiillII..

10The complete lineup must be

leveled to the highest point

of the floor. After the first

merchandiser has been set,

position the second so the

end frames touch.

A. Set a long level (4 foot or

more) on the upper front panel

of the merchandisers. Adjust

case height by rotating the

Adjustable Leg Leveler until

the merchandisers are flush

and level.

SSeeeeFFiigguurree77..

B. Also check each joint area

to be sure that the panels of

adjoining merchandisers are

flush to each other.

Levels on Upper

Front Panel

MINIMUM

HEIGHT

MAXIMUM

HEIGHT

Adjustable

Leg Leveler

Lower

Raise

Alignment Pins

DETAIL I.

Levels on Upper

Front Panel

Impact Service Merchandisers Joining Instruction

P/N 0420058

CASE 1 CASE 2

Merchandisers

HUSSMANN CORPORATION •BRIDGETON, MO 63044-2483 (Printed in U.S.A.)

11Slide the Lighting Rail

Joining Bracket (Item – 6)

across both light channel

extrusions to align the light

rails. SSeeeeFFiigguurree88..

12 Align the top extrusion and

insert Joining Plate (Item – 7).

Use #8 Screws — 8 to

fasten the plate using the pre-

drilled pilot holes as shown

in FFiigguurreess99aanndd1100..

13 Align the Rear Sill and

attach Joining Bracket

(Item – 9) with Washer Head

Machine Screw (Item – 10).

Use only specified fasteners.

Longer screws will penetrate

the rear sill causing damage.

SSeeeeFFiigguurree1111..

Fig. 9. Installing Joining Plate Fig. 10. Joining Plate in place

Fig. 11. Joining Rear Sill

Joining Plate

Pre- Drilled Holes

Rear Sill

Use only specified fasteners.

Longer screws will penetrate

rear sill.

CAUTION

Top Extrusion

Light Channel

Fig. 8. Front Lighting Rail Joining Plate

P/N 0420058

10-24 x 1/2

Machine Screw

Joining

Plate

14 Follow the sequence cor-

rectly when bolting the

cases together. See Figure 12.

Note: Make sure that no

more than (2) threads are

exposed when the cases

are bolted together. If

this does occur, the bolt

should be shortened,

replaced with a shorter

bolt or capped off accord-

ing to NSF specifications.

15 Fasten the fronts together

using Cap Screws (Item –11),

Flat Washers (Item – 12),

LockWashers (Item – 13)

and Hex Nut (Item – 14).

SSeeeeFFiigguurree1133..

HUSSMANN CORPORATION •BRIDGETON, MO 63044-2483 (Printed in U.S.A.) 9

Fig. 13. Fastening Front of CasesTogether (Sequence A)

Fig. 12. Sequence of Fastening

CASE

ONE

CASE

TWO

All Fasteners

are drawn out of scale

and larger for clarity

Impact Service Merchandisers Joining Instruction

P/N 0420058

16Fasten the rear of the cases

together at two locations

shown below using,

Spacers (Item – 15),

Cap Screws (Item – 16),

Flat Washers (Item – 17),

Lock Washers (Item – 18)

and Hex Nut (Item – 19).

SSeeeeFFiigguurree1144..DDeettaaiillJJ..

HUSSMANN CORPORATION •BRIDGETON, MO 63044-2483 (Printed in U.S.A.)

Fig. 14. Fastening Rear of CasesTogether (Sequence B)

Use caution when installing

fasteners around wiring or

refrigeration lines inside of

struts.

WARNING

DETAIL J.

P/N 0420058

Merchandisers

RH End of Case

from Front

Electrical Wires

always here

LH End of Case

from Front

Copper Tubing inside

encasement only

on gravity models

otherwise empty

Nut 19

Spacer Spacer

Hex Head

Cap Screw

Lock

Washer

Flat

Washer

CASE

ONE CASE

TWO

Flat

Washer

Top View of Joined Struts

Altri manuali per IMPACT ED1

Questo manuale è adatto per i seguenti modelli

Altri manuali Hussmann Merchandiser

Hussmann

Hussmann HGL-1BS Guida rapida

Hussmann

Hussmann RGDC Manuale di istruzioni

Hussmann

Hussmann IMPACT Excel B1X-GE Manuale di istruzioni

Hussmann

Hussmann BSM Manuale utente

Hussmann

Hussmann PWE Manuale utente

Hussmann

Hussmann microSC MNGSC8-A Manuale utente

Hussmann

Hussmann RED Manuale di istruzioni

Hussmann

Hussmann IMPACT CW2U-GE Manuale di istruzioni

Hussmann

Hussmann P4EP Manuale utente

Hussmann

Hussmann M1X-EP Manuale di istruzioni

Hussmann

Hussmann Impact Excel M5X-E Manuale di istruzioni

Hussmann

Hussmann ESBD Manuale di istruzioni

Hussmann

Hussmann Impact C2-E Manuale utente

Hussmann

Hussmann IMPACT LWEGH Manuale di istruzioni

Hussmann

Hussmann RID Istruzioni operative

Hussmann

Hussmann Impact Excel C6X-EP Manuale di istruzioni

Hussmann

Hussmann IMPACT LWU Manuale di istruzioni

Hussmann

Hussmann DSIO3-Y Istruzioni operative

Hussmann

Hussmann Excel FWG Manuale utente

Hussmann

Hussmann IMPACT RL Manuale utente

Hussmann

Hussmann Impact Excel M5X Manuale

Hussmann

Hussmann IMPACT Excel C3LGE Manuale utente

Hussmann

Hussmann FWG Manuale di istruzioni

Hussmann

Hussmann IMPACT Excel C2-X Manuale utente

Manuali Merchandiser popolari di altre marche

FRIGOGLASS

FRIGOGLASS Flex 20 HC Manuale utente

EPTA

EPTA COSTAN RHINO MULTI Manuale utente

CASCO

CASCO Nano Cube Manuale utente

True

True GDIM-26 Manuale utente

Structural Concepts

Structural Concepts Oasis Mobile Series Istruzioni per l'installazione

Haussmann

Haussmann RL Manuale utente

Howard McCray

Howard McCray R-CDS32E-4 Manuale utente

EPTA

EPTA iarp Cool Emotions Delight Lite Manuale utente

VALERA

VALERA BC 85 Manuale utente

HL Display

HL Display 3eBin Manuale utente

Dixie Narco

Dixie Narco DNCB 501E Manuale utente

APW Wyott

APW Wyott Racer DMXD-30H Manuale utente

Hoshizaki

Hoshizaki KD-90C Manuale utente

Summit

Summit SCR1006 Manuale utente

Delfield

Delfield Shelleyspeed SPM-28E Manuale utente

EPTA

EPTA iarp Cool Emotions GLEE 40 Manuale utente

Kysor/Warren

Kysor/Warren GranBering KW Guida

Crane

Crane BevMAX Refresh 6 Media Manuale utente