Hussmann IMPACT RL Manuale utente

NOTES: Insulated partitions are used

in a line-up between different models

or different temperature cases, and are

installed as the line-up is set.

Carefully unpack and inspect the

insulated partition and components

to ensure there is no breakage or

damage, and there are no missing

parts.

Be sure the first merchandiser has

been positioned and leveled according

to the installation instruction.

1Remove items from case as

shown in Figure 1 (both sides of

islands).

A. Remove bumpers, rails,

packing materials, and splash-

guards from both cases.

B. Remove shelves (if

installed).

C. Remove display racks and

pans from ends to be joined.

D. Remove rear shelf supports.

E. Remove back panels from

both cases by lifting up and out

near the bottom. No tools are

necessary.

F. Remove ‘J’ molding from

door frames next to partition.

G. RLNI ONLY: Remove the

interior top panels from end that

will receive partition.

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

P/N 0396231

November, 2002

Insulated Partition

Between

Reach-In Merchandisers

Field Installation Instruction

Merchandisers

PARTS LIST

Item Quantity Description

RL/RM/RMF

RLN/RMN RLNI

1. 2 4Donut Gasket

(Ships with Case)

2. 1 2Gasket 1 x 1/2x 180 in.

3. 1 2Gasket 1/2x 1/4x 180 in.

4. 1 1Partition Assembly

5. 7 14 Flat Washer 5/16

6. 6 12 Cap Screw 5/16-18 x 21/2 in.

7. 1 2Hex Head Lock Nut 5/16-18

8. 2 4End ‘J’ Molding

9. 10 20 Shoulder Screw

Figure 1. Remove Parts

2Verify that nut retainers are

installed in the right-hand end

of the left case in the locations

shown in Figure 2.

Remove all alignment pins from

cases that will join partition.

P/N 0396231

Merchandisers

2HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Factory Installed

Nut Retainer

Alignment Pin Alignment Pin

RLNI

Figure 2. Verify Nut Retainer Installation

RL / RM

and

RLN / RMN

Insulated Connecting Partition for Reach-In –

Installation Instruction P/N 0396231

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

1 in. x 1/2in.

Donut

1/2in. x 1/4in.

Gaskets must be

applied as shown on

both sides (L & R)

of partition

Make sure area where raceway attaches to end frame

is sealed with the wider 1 in. x 1/2in. gasket.

RL / RM / RMF

and

RLN / RMN

3Apply

Donut Gasket — 1

in end frame recessed locations

of both cases as shown in

Figure 3.

Apply the wider

Foam Tape Gasket — 2

as shown in Figure 3.

• Lap gaskets at lower corners.

• Check that there are no gaps

between gasket and case.

• Do not stretch gasket,

especially around corners.

• Do not butt gaskets; always

overlap joints.

• Remove paper backing after

gasket is applied to keep

gasket free of debris.

Apply the narrower

Foam Tape Gasket — 3

around the outside of the donut

gasket on both cases as shown

in Figure 3.

Gaskets

Must Be

Applied As

Shown

Make sure area where raceway attaches to end

frame is covered with wider 1 in. x 1/2in. gasket.

1 in. x 1/2in.

Donut

1/2in. x 1/4in.

RLNI

Figure 3. Apply Gaskets to Both Cases

4With the left-hand case leveled

in its permanent position, move

the joining case into alignment

approximately 4 in. (102 mm)

from left-hand case.

Slide the

Partition Assembly — 4

between the two cases and raise

it to align its joining holes with

those in the cases.

Insert long narrow rods (or

screwdrivers) through three or

more joining holes of the cases

and the partition to maintain

alignment, then bring the cases

firmly together to compress the

gaskets against the partition.

P/N 0396231

Merchandisers

4HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Alignment Pin

Figure 4. Insert Partition

5Fasten the cases together

through the end frames with

Washers — 5 under the head

of Cap Screws — 6 as shown

in Figure 5. Thread screws into

nut retainers at the locations

shown.

Once all the cap screws and

washers are in place, tighten in

the order shown in Figure 5.

Do not attempt to draw the cases

together with the cap screws.

Push the second case against the

partition and first case, compress-

ing all gaskets. Overtightening

can distort the end frame and

cause an incomplete seal which

will result in adverse case

performance, including leakage.

At lower front location, use

Hex Head Lock Nut — 7

and Cap Screw — 6 with

Washer — 5 under the head

as shown to fasten the partition

between the cases.

Insulated Connecting Partition for Reach-In –

Installation Instruction P/N 0396231

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Alignment Pin

Nut Retainer

Figure 5. Install Cap Screws,Washers and Hex Nut

6Fasten one

‘J’ Molding — 8

between the partition and the

door frame on each side as

shown in Figure 6 using

Shoulder Screws — 9.

Note that when fastening

through the hinge side of the

door frame, it may be necessary

to release the door retainer so

the door opens more than

90 degrees. Refer to manual that

shipped with the door.

7Replace rear shelf support, back

panels, display racks and pans,

and shelves removed in Step 1.

RLNI ONLY: First, replace the

interior top panels removed in

Step 1.

Once line-up is complete, install

bumpers and rails as shown in

Section 1 of the case installation

manual. Be sure to install the

splashguard brackets before

wiring or piping cases.

P/N 0396231

Merchandisers

6HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Figure 6. Install ‘J’ Molding

Altri manuali per IMPACT RL

Questo manuale è adatto per i seguenti modelli

Altri manuali Hussmann Merchandiser

Hussmann

Hussmann SSG Manuale utente

Hussmann

Hussmann LN Manuale di istruzioni

Hussmann

Hussmann BSM Manuale utente

Hussmann

Hussmann Impact Excel M5X-EP Manuale di istruzioni

Hussmann

Hussmann Impact C2-LGEP Manuale di istruzioni

Hussmann

Hussmann Impact M3 Manuale utente

Hussmann

Hussmann FW Manuale utente

Hussmann

Hussmann IMPACT M5NE Manuale utente

Hussmann

Hussmann ENTYCE TY3 Manuale utente

Hussmann

Hussmann impact C4LGE Manuale utente

Hussmann

Hussmann IMPACT LWG Manuale di istruzioni

Hussmann

Hussmann IMPACT D5G Manuale utente

Hussmann

Hussmann Q1-DC Wedge Istruzioni operative

Hussmann

Hussmann IMPACT Elite E2SP Manuale utente

Hussmann

Hussmann SHM-4 Guida rapida

Hussmann

Hussmann SMG8B Manuale utente

Hussmann

Hussmann SMB Manuale di istruzioni

Hussmann

Hussmann R3 Istruzioni operative

Hussmann

Hussmann IMPACT CW2-EGE Manuale utente

Hussmann

Hussmann NDD5 Manuale utente

Hussmann

Hussmann SMGT Manuale utente

Hussmann

Hussmann DM Manuale utente

Hussmann

Hussmann M1XD-GEP Manuale di istruzioni

Hussmann

Hussmann IMPACT ED1 Manuale utente

Manuali Merchandiser popolari di altre marche

FRIGOGLASS

FRIGOGLASS Flex 20 HC Manuale utente

EPTA

EPTA COSTAN RHINO MULTI Manuale utente

CASCO

CASCO Nano Cube Manuale utente

True

True GDIM-26 Manuale utente

Structural Concepts

Structural Concepts Oasis Mobile Series Istruzioni per l'installazione

Haussmann

Haussmann RL Manuale utente

Howard McCray

Howard McCray R-CDS32E-4 Manuale utente

EPTA

EPTA iarp Cool Emotions Delight Lite Manuale utente

VALERA

VALERA BC 85 Manuale utente

HL Display

HL Display 3eBin Manuale utente

Dixie Narco

Dixie Narco DNCB 501E Manuale utente

APW Wyott

APW Wyott Racer DMXD-30H Manuale utente

Hoshizaki

Hoshizaki KD-90C Manuale utente

Summit

Summit SCR1006 Manuale utente

Delfield

Delfield Shelleyspeed SPM-28E Manuale utente

EPTA

EPTA iarp Cool Emotions GLEE 40 Manuale utente

Kysor/Warren

Kysor/Warren GranBering KW Guida

Crane

Crane BevMAX Refresh 6 Media Manuale utente