ICP DAS USA IP-8000-MRTU Manuale utente

iP-8000-MRTU Quick Start Guide

Quick Start Guide for

iP-8000-MRTU

May 2014, Version 1.0.1

Congratulations on purchasing iP-8000-MRTU - the most popular automation solution for

remote monitoring and control application. This Quick Start Guide will provide information

needed to get started.

In addition to this guide, the package includes the following items:

iP-8000-MRTU Software Utility CD RS-232 Cable Screw Driver

(iP-8411-MRTU/iP-8811-MRTU) (CA-0915) (1C016)

●iP-8000-MRTU Reference Document

CD:\Napdos\Modbus\IP8000R\Document\

http://ftp.icpdas.com/pub/cd/8000cd/napdos/modbus/ip8000r/document/

●iP-8000-MRTU Website

http://www.icpdas.com/root/product/solutions/pac/ipac/ip-8x11-mrtu.html

●ICP DAS Website

http://www.icpdas.com/

iP-8000-MRTU Quick Start Guide

Mounting the Hardware

The iP-8000-MRTU installation must provide proper ventilation, spacing, and grounding

to ensure the equipment will operate as specified. A minimum clearance of 50mm

between the iP-8000-MRTU and the top and bottom side of the enclosure panels must

be provided.

Configure the Boot Mode

Before starting any installation, be sure that

the DIP switch is placed in the “Run” position.

Connecting to PC and Setting up the Power

i. Connect PC to COM1through a RS-232 cable.

ii. Connect the +24 VDC power supply to PWR1 and GND terminals.

iP-8000-MRTU Quick Start Guide

Inserting and Wiring the I/O Modules

There are various types of I/O expansion modules for interfacing many

different field devices to the iP-8000-MRTU.

For more information about I/O expansion

module, please refer to

http://www.icpdas.com/products/PAC/xpac/remote_io_support_list.htm

Setting the Net ID

The Net ID must be unique in the network. It can be from 01

to FF. This 8-bit DIP switch allow you to change the Net ID.

After setting the Net ID, the iP-8000-MRTU must be

rebooted to apply the new Net ID.

Installing the Modbus Utility

The Modbus Utility can be obtained from companion CD or ICP DAS

FTP site:

CD:\Napdos\Modbus\Modbus_Utility\

ftp://ftp.icpdas.com/pub/cd/8000cd/napdos/modbus/modbus_utility/

Net ID 1 2 3

01 On - -

03 On On -

05 On - On

iP-8000-MRTU Quick Start Guide

Using the Modbus Utility to Configure the Module

The Modbus Utility can be used to make the communication between the iP-8000-MRTU

and PC/Laptop via the Modbus RTU/ASCII protocol.

Step 1: Run the Modbus Utility and connect to iP-8000-MRTU.

i. Double-click the Modbus Utility shortcut on the desktop.

ii. Click the Modbus/RTU

button in the middle of

the Select Controller

dialog.

iii. Select the COM port, and then click the Connect button. Click the Search button in

the Search List

dialog box to

scan the Net ID

iP-8000-MRTU

on the COM

port.

iv. If the Net ID of iP-8000-MRTU was

found, click the Stop button first, and

then select the Net ID and click the

Connect to Selected ID button to

connect. The default value for COM1

of iP-8000-MRTU is 115200, N, 8, 1,

RTU Mode.

Step 2: Match the I/O module and then get the I/O configuration information.

iP-8000-MRTU Quick Start Guide

i. Click the Refresh button to match the I/O modules to configuration of the controller.

ii. Select the About option from the Help menu to get the I/O configuration and firmware

information.

iii. Check the module

status diagram,

ensuring for the I/O

modules to be

matched.

Step 3: Set I/O configuration, get the I/O values and then save the I/O

configuration.

i. Click the Refresh button.

iii. See the module status diagram,

ensuring for the I/O modules to

be matched.

ii. Select the

About

option

from the Help menu.

iP-8000-MRTU Quick Start Guide

i. Configure the I/O settings, such

as Range Code, Power-on and

Safe values.

ii. Select the Timer Interval from

the Monitor menu to set the

monitoring interval.

iii. Click the

Monitor

icon to start

retrieving

I/O values.

The I/O

values will

displayed in the Mapping tables.

iv.

Select File option from the Save

menu and select a location

where the configuration file is

about to be saved. This

operation can save the

controller configuration and I/O

settings to an “ini” file, and the

file can be loaded by Load function at the next time when using the same controller

and I/O modules.

ii. Select the Timer Interval to

set the monitoring interval.

iv. Click File to save the

configuration file.

iP-8000-MRTU Quick Start Guide

Q & A

1.How do I know the COM Port settings?

The COM Port setting will be displayed on the 7-seg

LED.

The first number is the COM Port number. This

example shows the settings of COM1 are 115200

Baud Rate, 8 Data Bits, None Parity, 1 Stop Bit and

Modbus RTU Slave Mode. The COM Port settings

can be configured with the Modbus Utility. The new

settings will take effect after rebooting the

iP-8000-MRTU.

The figure of ASCII Mode shows as left-hand

side.(COM1, Mode= Modbus ASCII)

2.How could I set the COM Port to the Modbus RTU Slave Mode?

Step1: Run the Modbus Utility and connect to

the iP-8000-MRTU.

Step2: Click the COM Port icon to display the

setting area.

Step3: Select the COM Port from the

drop-down list.

Baud Rate

[1.1152]

Data Bits/Parity/Stop

Bits [1.801]

RTU/ASCII

[1.RTU]

iP-8000-MRTU Quick Start Guide

Step4: Select the Enable Mode to

Modbus/RTU Slave, and set the

Modbus Timeout, Baud Rate, Data

Bits, Parity and Stop Bits.

Step5: Click the Set button to

apply for new settings.

3.How do I reset the COM Port to the default value?

Step1: Go to 7-seg LED, press the MODE

and SET buttons simultaneously for

about 2 seconds.

Step2: Wait for 2 seconds, the word “RESET” appeared.

Press the buttons until the LED is flickering, and

then the COM Ports are all set to default values.

The default COM Port values are 115200, N, 8, 1,

RTU Mode.

Aese7

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ICP DAS USA Controllori

ICP DAS USA

ICP DAS USA PISO-CAN200 Manuale utente

ICP DAS USA

ICP DAS USA GRP-2841M-5GE Manuale utente

ICP DAS USA

ICP DAS USA WISE-580 Series Manuale utente

ICP DAS USA

ICP DAS USA I-7188E3 Manuale utente

ICP DAS USA

ICP DAS USA LinPAC-22 Series Manuale utente

ICP DAS USA

ICP DAS USA VPD Series Manuale utente

ICP DAS USA

ICP DAS USA WISE-52 Series Manuale utente

ICP DAS USA

ICP DAS USA I-7188XC Manuale utente

ICP DAS USA

ICP DAS USA GT-530 Manuale utente

ICP DAS USA

ICP DAS USA LP-9821 Manuale utente

ICP DAS USA

ICP DAS USA I-7188XG Manuale utente

ICP DAS USA

ICP DAS USA 7188E Istruzioni per l’uso

ICP DAS USA

ICP DAS USA uPAC-7186EG Manuale utente

ICP DAS USA

ICP DAS USA WinCon 8000 Istruzioni per l’uso

ICP DAS USA

ICP DAS USA TPD-280-H Manuale utente

ICP DAS USA

ICP DAS USA SMS-531 Manuale utente

ICP DAS USA

ICP DAS USA WISE-75 M Series Manuale utente

ICP DAS USA

ICP DAS USA ISaGRAF WinCE ViewPAC Manuale utente

ICP DAS USA

ICP DAS USA I-7188E3D-232 Manuale utente

ICP DAS USA

ICP DAS USA WinPAC-5000 Manuale utente

ICP DAS USA

ICP DAS USA CAN-8123 Guida all'installazione

ICP DAS USA

ICP DAS USA LinPAC AM335 Series Manuale utente

ICP DAS USA

ICP DAS USA WISE-52 Series Manuale utente

ICP DAS USA

ICP DAS USA XP-9 88-IoT Series Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente

ICP DAS USA iP-8000-MRTU Manuale utente

Manuali Controllori popolari di altre marche