IDEAL 33-772 Manuale utente

IE Net PRO Cable Tester

Eight modes of operation

1. DATA – cable test mode 5. HUB BLINK

2. COAX (RJ45) – cable test mode 6. Set up Mode

3. LENGTH – Cable length measure 7. OFF

4. TONE 8. Voltage Protection

Press MODE to select any of the seven modes of operation, press SELECT to

enter selected operation mode and proceed,

Press SELECT for two seconds to turn backlight on/off.

DATA – Data Cable Test

1. Press any of the four keys to power on

the tester; when powered on, M12,

M12>RJ45, RJ45 shows on the first

line of the screen;

2. M12 is the default setting; use Up or

Down arrow keys to select M12>RJ45

or RJ45

M12– for 2-pair data cable test

When in M12 mode and no cable is

connected, the display shows:

1. When in M12 mode “No shield” is

default setting

2. Exit to SETUP to change options

(see Set Up mode)

3. When using M12 mode, the Split Pair

function is automatically disabled.

Standby - Cable Test (Pre-Test)

1. When in M12 mode,

2. Connect cable to the Tester (see

following screens for more

demonstrations )

Note: When there is no Remote

connected, Shield and No Shield will

not appear)

33-772

M12 M12>RJ45 RJ45

 to change type

MODE=ESC, SEL=go

Test M12

1234

Open 1-3 2-4

Displays and cycling in sequential order

1-3, 2-4, No Cable

Test M12

12 34

Pass Pre-Test

15.5 ft

Cycling in sequential order

1 2, 3 4

PK Elektronik Vertriebs GmbH, E-Mail: [email protected], Internet: www.pkelektronik.com

M12 - Setup

To change between shielded & unshielded cable, toggle Beeper to select

length units.

When in SETUP mode -

 •UseUporDownarrowkeysandscroll

to Shielded and Unshielded, press

SELECT to change.

 •SelectablePassBeep-OnandPass

  Beep-Offfunctionisalsoavailablein

this SETUP mode, press Up or Down keys to select and press SELECT to

choose. (Note: Beeper sounds when test passes, and when voltage is

detected on a cable.)

 •Inthismode,pressUpandDownkeystoselectbetweenunitsoflength,

  Units-feetorUnits-meters,pressSELECTkeytoselect.

M12 – for 2-pair data cable test

Test in Progress - Cable Test

1. When the test is running, “Test” blinks;

when test is completed, “Pass” or “Fail”

shown;

2. Remote ID shown when wire map

passes;

3. The last line shows the length of cable being tested;

4. Beeper icon appears only when Beeper is OFF; low battery icon appears

only when the battery is below 5.5V

Results of a corectly wired shielded cable

1. When the test is running, “test result

shows “Pass”;

2. Remote ID shown when wire map

passes;

3. The last line shows the length of cable

being tested;

4. Beeper icon appears only when Beeper is OFF; low battery icon appears

only when the battery is below 5.5V

SETUP

Unshielded

SEL to change

Test M12

1234 No Shield

1234 ID 1

1.5m

PASS M12

1234 Shielded

1234 ID 1

1.5m

PK Elektronik Vertriebs GmbH, E-Mail: [email protected], Internet: www.pkelektronik.com

Results of a cross-over, shielded cable

1. “Pass” shown on the first line;

2. Wire Map shows wiring configuration

1324 and ID # indicates the particular

Remote which is in use;

3. “M12 X-Over” displayed on the

last line;

4. Beeper icon appears only when Beeper is OFF; low battery icon appears

only when the battery is below 5.5V

M12 to RJ-45

Cable Test

 WheninM12>RJ-45modeandnocable

is connected, the display shows:

1 M12>RJ45 mode

2. “No shield” is default setting

3. Exit to SETUP for more options

(see Set Up mode)

4. When using M12>RJ45 mode, the

Split Pair function is automatically

disabled.

Setup

To change between shielded and unshielded cable, toggle Beeper to select

length units.

 WheninSETUPmode-

 •UseUporDownarrowkeysandscroll

to Shielded and Unshielded, press

SELECT to change.

 •SelectablePassBeep-OnandPass

  Beep-OfffunctionisalsoavailableinthisSETUPmode,pressUporDown

keys to select and press SELECT to choose. (Note: Beeper sounds when test

passes, and when voltage is detected.)

 •Inthismode,pressUpandDownkeystoselectbetweenunitsoflength, 

  Units-feetorUnits-meters,pressSELECTkeytoselect.

Standby - Cable Test (Pre-Test)

 1.WheninM12>RJ-45mode,

2. Connect cable to the Tester (see

following screens for more

demonstrations)

Note: When there is no remote connected,

shield and no shield will not appear

PASS M12

1234 Shielded

1324 ID 1

M12 X-Over

Test M12>RJ45

1234

Open 1-2 3-6

Displays and cycling in sequential order

1-2, 3-6, No cable

Cycling in sequential order 1 2, 3 4

SETUP

Unshielded

SEL to change

Test M12>RJ45

12 34

Pass Pre-Test

15.5 ft

PK Elektronik Vertriebs GmbH, E-Mail: [email protected], Internet: www.pkelektronik.com

Test in Progress - Cable Test

1. When the test is running, “Test” blinks;

when test is completed, “Pass” or “Fail”

shown;

2. Remote ID shown when wire map

passes;

3. The last line shows the length of cable being tested;

4. Beeper icon appears only when Beeper is OFF; low battery icon appears

only when the battery is below 5.5V

Results of a correctly wired good shielded cable:

1. When the test is running, “test result

shows “Pass”;

2. Remote ID shown when wire map

passes;

3. The last line shows the length of cable

being tested;

4. Beeper icon appears only when Beeper is OFF; low battery icon appears

only when the battery is below 5.5V

Results of a cross-over, shielded cable:

1. “Pass” shown on the first line;

2. Wire Map shows wiring configuration

3162 and ID # indicates the particular

Remote which is in use;

3. “M12>RJ45 X-Over” displayed on

the last line ;

4. Beeper icon appears only when Beeper is OFF; low battery icon appears

only when the battery is below 5.5V

Results of a 2-pair cable, where 1-2 pair found open

1. When a pair of wire was found open,

the two missing pin numbers in line 2

of the wire map indicates the open pair;

2. The last line shows an error message

“Open 1-2”

Test M12>RJ45

1234 No Shield

ID 1

1.5m

PASS M12>RJ45

1234 Shielded

1326 ID 1

1.5m

PASS M12>RJ45

1234 Shielded

3162 ID 1

M12>RJ45 X-Over

Fail M12>RJ45

1234 Shielded

3 6 ID 1

Open 1-2

PK Elektronik Vertriebs GmbH, E-Mail: [email protected], Internet: www.pkelektronik.com

Results of a 2-pair cable, where 3-6 pair found open

1. When a pair or wire was found, the two

missing pin numbers in line 2 of the

wire map indicates the open pair;

2. The last line shows an error message

“3-6”

Results of a 2-pair cable, where 1, 2 wire of M12 or 1, 3 wire of

RJ-45 found shorted

1. When a single wire was found shorted

with another one, the two missing pin

numbers in line 2 of the wire map

indicates the shorted pair;

2. The last line shows an error message

“Short 13”

Test results of a 2-pair cable, where 3,4 wire of M12 or 2,6 wire of

RJ-45 found shorted:

1. When a single wire was found shorted

with another wire, the two missing pin

numbers in line 2 of the wire map

indicates the shorted pair;

2. The last line shows an error message

“Short 26”

Test results of a 2-pair cable, where 1,2 wire of M12 or 1,3 wire of

RJ-45 found mis-wired:

1. When there is miswire the wire map

shows the pin numbers;

2. An error message “Miswire 13”

appears on the last line.

RJ-45 - for 4-pair data cable test

 WhenRJ-45modeisselectedandno

cable is connected, the display shows:

Fail M12>RJ45

1234 Shielded

1 2 ID 1

Open 3-6

Fail M12>RJ45

1234 Shielded

**26 ID 1

Short 13

Fail M12>RJ45

1234 Shielded

13** ID 1

Short 26

Fail M12>RJ45

1234 Shielded

3126 ID 1

Miswire 13

Test RJ45

12345678

Open 1-2 3-6 4-5 7-8

1-2, 3-6, 4-5, 7-8 No Cable

PK Elektronik Vertriebs GmbH, E-Mail: [email protected], Internet: www.pkelektronik.com

Standby - Cable Test

1.WheninRJ-45mode,

2. Connect cable to the Tester (see following

screens for more demonstrations) Note:

When there is no remote connected,

shield and no shield will not appear.

Test in Progress - Cable Test

1. Test repeats every 3 seconds (max.);

when test is in progress, “Test” appears

on the first line, when test is completed,

test result “Pass” or “Fail” appears

replacing “Test”;

2. Wire Map shows correct wiring when ID # indicates the particular Remote

which is in use;

3. The last line shows the length of cable being tested;

4. Beeper icon appears only when Beeper is OFF; low battery icon appears

only when the battery is below 5.5V

Test results of an all normal shielded cable with TIA-568-B wiring:

1. “Pass” appears on the first line;

2. Wire Map shows correct wiring when

ID # indicates the particular Remote

which is in use;

3. The last line shows the length of cable

being tested;

Test results of a shielded 4-pair data cable, T-568-B wiring, but a

cross-over cable

1. “Pass” appears on the first line;

2. Third row of screen displays pin numbers

  wherecross-overwasdetected;

3. “RJ-45 X-OVER” displayed on the

last line.

Test result of an unshielded 4-pair data cable, standard T-568-B

wiring, No Remote Unit is connected and with 1,3 Shorted, screen

displays as:

1. When test is in progress “Test” blinks;

when test is completed “Test” goes off

and is replaced by “Fail”.

2. Third row of screen displays

”No Remote?”;

 3.Errormessages“Short1-3”displayed

on the last line.

Test RJ45

12 36 45 78

Pass Pre-Test

15.5 ft

Cycling in sequential order 1-2, 3-6, 4-5,

7-8

Test RJ45

12345678 No Shield

12345678 ID1

11.5m

Test RJ45

12345678 Shielded

12345678 ID1

11.5m

Pass RJ45

12345678 Shielded

36145278 ID 1

RJ45 X-OVER

Fail

No Remote?

Short 13

PK Elektronik Vertriebs GmbH, E-Mail: [email protected], Internet: www.pkelektronik.com

Test result of an unshielded 4-pair data cable, standard T-568-B

wiring, tested with 4,6 shorted; screen plays as:

1. When test is in progress “Test” blinks;

fault (shorted at 46) was detected, “Test”

goes off and is replaced by “Fail”. The

third row displays ** at pin numbers 4,6

which was the pin or pair found shorted.

 2.Errormessage“Short4-6”shownonlast

line replacing cable length.

Test result of an unshielded 4-pair data cable, standard T-568-B

wiring, tested with 1,2 Open:

1. When test is in progress “Test” blinks;

when test is completed, error (Open at

  1-2)wasfound,“Test”goesoffand

shows ‘Fail’.

2. The wire map shows two missing pin

numbers indicating the open wire;

 3.Errormessage‘Open1-2’appearsonthelastline.

Test result of an unshielded 4-pair data cable, standard T-568-B

wiring, tested with 7-8 pair mis-wired; screen displays:

1. When test is in progress “Test” blinks;

  whencompleted,error(mis-wiredat

  7-8)wasfound,“Test-”goesoffand

  “Failing-’shown.Thethirdrow

displays pins 12345687, in which

  78pairwasfoundmis-wired.

Test results of an unshielded 4-pair data cable, with all 8 pins

reversely wired; screen plays:

1. When test is in progress “Test”

blinks; when completed, error was

found, “Test” goes off and “Fail”

appears

2. The third row displays pins

  87654321foundmis-wired.

3. The forth row displays error message Miswire 1 2 3 6 , Miswire 4 5 7 8 and

repeats.

Fail RJ45

12345678 No Shield

123*5*78 ID 1

Short 46

Fail RJ45

12345678 No Shield

345678 ID 1

Open 1-2

Fail RJ45

12345678 No Shield

12345687 ID 1

Miswire 78

Fail RJ45

12345678 No Shield

87654321 ID 1

Miswire 1236

PK Elektronik Vertriebs GmbH, E-Mail: [email protected], Internet: www.pkelektronik.com

Test result of an unshielded 4-pair data cable, standard T-568-B

wiring, Remote Unit attached, tested with 1-2, 3 -6 split; screen

plays as:

1. When test is in progress “Test” blinks;

when test is completed, error

(Split 12, 36) was found, “Test” goes off

and is replaced by “Fail”. The third row

displays split pin numbers 1236 and

blinks.

2. Error message “Split 1236” shown on last line replacing cable length.

3. Minimum cable length for testing = 1.0 meter or 3 ft.

Test result of an unshielded 4-pair data cable, standard T-568-B

wiring, Remote #1 in use; tested with 1-2 Opened, 3-6 shorted,

7-8 mis-wired; screen displays multiple errors as:

1. When test is in progress “Test” blinks;

when test is completed and multiple

errors detected, “Test” goes off and is

replaced by “Fail”.

2. On the third row, screen displays pin

numbers*45*87 where errors such as

  Open1-2,Short3-6,7-8mis-wiredwere

detected.

3. Multiple errors messages are displayed

on the last row cycling in orders of

severity with Short comes first.

COAX (RJ-45) - Coax Cable Test

1. When in Coax (RJ45) mode, press

SELECT to perform test;

2. The Coax (RJ45) mode is used in

conjunction with eight special numbered

 andcolor-codedF-ConnectorsTerminals,

each has its signature that the IE Net Pro can identify.

3. When using Coax (RJ45) mode, the Split Pair function is automatically

disabled.

Fail RJ45

12345678 No Shield

12345678 ID 1

Split 1236

Fail RJ45

12345678 No Shield

4 5*87 ID 1

Short 36

Cycling in sequential order of

Short 36

Open 1-2

Miswire 78

COAX (RJ45)

MODE=ESC, SEL=go

PK Elektronik Vertriebs GmbH, E-Mail: [email protected], Internet: www.pkelektronik.com

Results of testing a good coax cable, No.5 (Green) Coax Terminator

being used; screen displays as:

1. “PASS” shown on the first line and Coax

(RJ45) mode also shown on first line;

2. On the third line, the remote number and

color code are displayed;

3. When a Remote Terminator is

connected, no length information

will be displayed on the screen.

(when measuring the length of a

coax cable, no remote should be

used, see screen#L-10 of LENGTH

mode)

Results of testing a coax cable without a F-Connector Terminator

attached; screen displays as:

1. “FAIL” shown on the first line and the

 Coax(RJ-45)mode;

2. On the third line, “Open” is shown

Note: the eight specially numbered and

 color-codedF-ConnectorTerminators

must be used in conjunction with Coax

cable test mode.

Results of testing a shorted cox cable; screen displays as:

1. “FAIL” shown on the first line and the

 Coax(RJ-45)mode;

2. On the third line, “Short” is displayed;

LENGTH Mode - Description (1)

•Measuringcablelengthbymeasuringitscapacitanceandusingthecapacitance

per unit of length (length constant) to calculate the length.

•ConnectcabletotheMainunit(withorwithoutthepresenceofaRemoteat

the other end).

•PressanykeytoturnontheTester,pressMODE,scrollthroughandselect

 LENGTHmode,pressSELECTkeytoenter(seeScreen#L-1)

• UseUpandDownarrowkeystoselecttypeofcable(M12-2pair

data cable, M12>RJ45 for M12 to RJ45 cable, RJ45 for 4-pair data

cable or Coax (RJ45) for coaxial cable) to test (see screen #L-2),

press SELECT to proceed with cable length measure.

Pass COAX (RJ45)

5 Green

Connect one end of the cable to the main

unit by means of a RJ-45 plug to Coax

Adapter and any one of the eight color

coded Coax Terminators must be

attached on the other end to perform test.

Fail COAX (RJ45)

Open

Fail COAX (RJ45)

Short

PK Elektronik Vertriebs GmbH, E-Mail: [email protected], Internet: www.pkelektronik.com

Data Cable Length Measurement

•Onthistester,M12isdefault,whenitisselecteda5-secondinstantmessage

“select for pair#” appears on the screen; use SELECT key to scroll through

1-2,3-4,autoandselectapairtomeasure.(seescreen#L-3)

•M12>RJ-45comesnext,whenthisdatamodeisselected,useSELECTkeyto

scroll through 12, 36 or auto to select a pair to measure length.

•WhenRJ-45isselecteda5secondinstantmessage“selectforpair#”appears

onthescreen;useSELECTkeytoscrollthrough1-2,3-6,4-5,7-8,autotoselect

apairtomeasurelength.(seescreen#L-4#L-5)

•TheIENet™PROisdefaulttotest1-2pairwhenenteringintolengthmeasure

mode;andifthereisanerrororafaultdetected(seeScreen#L-6)itwillauto-

matically switch to a second pair to carry on the testing.

•ChangelengthconstantbymeansofUpandDownarrowkeys,CALiconis

on when adjusting the constant and goes off when setting is done (see screen

#L-7).

•ExittoSETUPmodetochangeunitoflengthfromfttometer.

Coax Cable Length Measurement

•ConnectcabletotheMainunitbyusinganAdapter(whenmeasuringcoax

cable length, no Remote Terminator is required). Press any key to turn on the

Tester, press MODE, scroll through and select LENGTH mode, press SELECT

keytoenter(seeScreen#L-1)

•When measuring length of a coaxial cable, no remote is required;

1-2 is default pair and must be used for coax length measure.

•UseUpandDownarrowkeystoselectCoax(RJ45)astypeofcabletotest(see

screen#L-10),pressSELECTkeytoproceedwithcablelengthmeasurement

•ChangelengthconstantbymeansofUpandDownarrowkeys,CALiconison

whenadjustingtheconstantandgoesoffwhendone.(Seescreen#L-11)

•Tochangeunitofmeasurementfromfttometer,useSETUPmode.(seescreen

#S-7atSETUPmode)

If the far end of the cable is connected to a Network Device (Hub, Switch, etc.), the

testerwilldisplay“TRingNetwork?”(mostlyonunknowndevices),or“XBase-T

Network?” (when connected to a HUB) or “Network?” (when connected to a

Switch).Seescreens#L-12to#L-14.

Measuring a Data Cable

Screen#L1-LENGTHmode

LENGTH

MODE=next,SEL=go

PK Elektronik Vertriebs GmbH, E-Mail: [email protected], Internet: www.pkelektronik.com

Indice

Lingue:

Altri manuali IDEAL Tester per cavi

IDEAL

IDEAL 33-856 Manuale utente

IDEAL

IDEAL LANTEK 7G Manuale utente

IDEAL

IDEAL LT 8000 series Guida di riferimento

Manuali Tester per cavi popolari di altre marche

VOLTCRAFT

VOLTCRAFT CT-2 Manuale utente

Whirlwind

Whirlwind Connect DCT-9 Manuale utente

Triplett

Triplett CTX200 Manuale utente

Greenlee

Greenlee 45395 Manuale utente

Test-Um

Test-Um Validator-NT NT955 Manuale utente

Fluke

Fluke MicroMapper Manuale utente

Radiodetection

Radiodetection RD8100 Manuale utente

Vonaq

Vonaq EasyCheck 900 Manuale utente

Softing

Softing CableMaster CM200 Manuale utente

Microtest

Microtest 8751 Manuale utente

Psiber Data Systems

Psiber Data Systems 20 Manuale utente

Platinum Tools

Platinum Tools LANSeeker TP500C Manuale utente

Triplett

Triplett WireMaster HDMI2 Manuale utente

Tenmars

Tenmars LC-90 Manuale utente

BIRD

BIRD SITE ANALYZER SA-1700EX Manuale utente

Softing

Softing WireXpert 4500 Manuale utente

Vision

Vision V18-310 Manuale utente

Black Box

Black Box Scan-LAN 80 Manuale utente