IDS HYYP Manuale utente

IDS HYYP IP Connect

With WiFi Module

Introduction

The IDS HYYP IP Connect Module is a plug on module for the X-Series alarm panels. The HYYP

IP Connect Module will enable your X-Series panel to communicate with the HYYP platform

allowing it to report to your HYYP Base Station

(monthly charges apply)

and the HYYP Home

mobile app.

1.Installation

1.1. Wiring

Connect the HYYP IP Connect Module 12v input to the TX connectors of the X-Series panel. Be

sure to connect the 12V to positive and GND to Negative.

Connect the provided serial cable from the serial connector on the X-series panel to the serial

connector on the HYYP IP Connect Module.

Tip: The red wire on the X-Series panel should be closest to the panel’s heat sink.

Plug in the Ethernet cable from the network to the

Ethernet connector, or connect to your WiFi. If the

WiFi module is installed the Ethernet port is

ignored.

NB: The HYYP IP Connect Module can only get an IP

address from a DHCP server. You cannot give it a static

IP address.

1.2. Connecting to WiFi

To connect your IP Connect with WiFi module to your wifi you must have a WPS enabled router.

To use WPS simply power the IP Connect with the WiFi Module

and when the Panel Comms, Network Comms and Server Auth

LEDS start flashing one at a time in a clockwise sequence press

the WPS button on your router.

1.3. Programming

Location 196 is needed if you want to use the HYYP Home app, reporting should still work

without location 196 programmed.

Enter Installer Code [9][9][9][9][*]

Go to location 196 [1][9][6][*]

Enter any six digit code [1][2][3][4][5][6][*]

(This is to authorise the HYYP serial connection)

Go to location 61 [6][1][*]

(This is the partition’s account code: 61 – Partition 1; 62 –Partition

2; 63 –Partition 3…)

Enter the account code issued by the control room [1][2][3][4][*]

Exit installer programming [#]

2.HYYP Home App

With HYYP Home you have remote access to monitor and control your home or business

anywhere, anytime, in real time.

2.1. Installing the HYYP Home App

To install the HYYP Home App go to the Google Play

Store and search for HYYP Home. And click install.

Once installed open the HYYP Home App, the first time you open the app you will be asked to

Click ‘Sign Up’ to register and activate a device to the

app.

Fill in your details, accept the terms and conditions and click

2.2. Adding a site

Once registered you will be given a HYYP ID and asked if you have a HYYP IP Connect to

connect. Click ‘I have a new HYYP Hub’.

Give your HYYP IP Conect a name and choose a site

colour. The site colour will help distinguish between

multiple sites.

Click ‘Continue’.

Enter the HYYP IP Connects Unique ID number or scan

the unique barcode on the HYYP IP Connect.

Click ‘Continue’.

To add the HYYP IP Connect Module to the HYYP Home

app you must enter location 196 when the app asks you to

synchronise the device.

Fill in details of where the HYYP Serial is installed.

Click ‘Next’.

Your HYYP Serial has successfully been synced with the HYYP

Home app.

3.Troubleshooting

3.1. LEDs

The HYYP IP Connect Module has 4 LEDs that you can use to view its status.

Power LED –On when the HYYP IP Connect Module has sufficient power.

Panel Comms LED –Flashes when communicating with the X-Series Panel.

Network Comms LED –Flashes when communicating on the network.

Server Auth LED –On when connected to the HYYP platform.

On power up the Network Comms and Server Auth LEDs will flash together, and once it has

made a successful connection to the HYYP platform the Server Auth LED will stay on and the

Network Comms LED will flash when it’s communicating on the network.

If the Server Auth and Network Comms LEDs continue to flash the same number then there is

an error on the HYYP IP Connect Module. You can determine the error by the amount of times

the LEDs flash.

See error numbers below:

1 –System error –

Replace unit.

2 –Can’t initialise Ethernet port.

3 –Can’t get IP address from DHCP server.

4 –Can’t connect to the Time server.

5 –Unable to log on to the HYYP platform.

6–Unable to register on the HYYP platform.

3.2. IP Ports

These are the ports that are needed for the HYYP IP Connect to connect to the HYYP servers.

None of these ports or IP addresses must be blocked.

1) Request DHCP server to provide IP address details

2) DNS lookup of tick.meraka.csir.co.za destination Port 53 & 54

a) This will use the DNS server given by DHCP

3) It will then get time using NTP - Destination Port 123

4) DNS lookup of mqtt.trintel.co.za

5) The HYYP IP Connect then communicates to mqtt.trintel.co.za on MQTT encrypted

port 8883 (from v1.11)

a) If the HYYP IP Connect cannot connect on 8883, the HYYP IP will fall back to standard

MQTT port 1883

Indice

Altri manuali IDS Unità di controllo

IDS

IDS AM-19201080NTZQW-T01 Manuale utente

IDS

IDS SMS Duo Manuale utente

IDS

IDS X Series Guida all'installazione

IDS

IDS X-Series X-SMS V2 Manuale di istruzioni

IDS

IDS hyyp AppConnectLTE Plugon Manuale utente

IDS

IDS C-S-25H0-096 Manuale utente

IDS

IDS X Series Guida utente

IDS

IDS AM-1024768Z3TZQW-TH0H Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente