IEI Technology PSC-586VGA Manuale utente
PSC-586VGA
ISA/PCI Pentium™w/ VGA
Single Board Computer
@Copyright 1996
All Rights Reserved.
Manual first edition May 05,1996
The information in this document is subject to change without prior notice in
order to improve reliability, design and function and does not represent a
commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use or inability to use
the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All
rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
Trademarks
PSC-586VGA is registered trademarks of Acquire Inc.,IBM PC is a registered
trademark of International Business Machines Corporation. Intel is a
registered trademark of Intel Corporation. AMI is registered trademarks of
American Megatrends, Inc. Other product names mentioned herein are used
for identification purposes only and may be trademarks and/or registered
trademarks of their respective companies.
1
Contents
1. Introduction.................................................................3
1.1 Specifications.........................................................................................4
1.2 What You Have......................................................................................5
2. Installation...................................................................6
2.1 PSC-586VGA's Layout...........................................................................6
2.2 Unpacking..............................................................................................8
2.3 Jumper Description ................................................................................9
2.4 Setting the CPU of PSC-586VGA.........................................................10
2.5 Upgrade the External Cache.................................................................11
2.6 System Memory DRAM.......................................................................11
2.7 Watch-Dog Timer.................................................................................11
2.8 FDC37C665/ALI M5113 Multi-I/O Chip..............................................12
2.9 PCI VGA Controller ............................................................................12
3. Connection................................................................13
3.1 Floppy Disk Drive Connector ...............................................................13
3.2 IDE Disk Drive Connector....................................................................14
3.3 Parallel Port.........................................................................................15
3.4 Serial Ports ..........................................................................................15
2
3.5 Keyboard Connector.............................................................................16
3.6 External Switches and Indicators..........................................................16
3.7 External Speaker..................................................................................17
3.8 PS/2 Mouse Port .................................................................................17
3.9 VGA Connector ...................................................................................18
4. AMI BIOS Setup.......................................................19
4.1 Getting Start ........................................................................................19
4.2 Standard Setup.....................................................................................20
4.3 Advanced Setup ...................................................................................21
4.4 Chipset Setup.......................................................................................23
4.5 Peripheral Setup...................................................................................25
4.6 Power Management Setup....................................................................26
Appendix A. Watch-Dog Timer.....................................27
3
1
Introduction
Welcome to the PSC-586VGA ISA/PCI Pentium w/VGA Single
Board Computer. The PSC-586VGA board is an ISA/PCI form
factor board, which comes equipped with high performance
Pentium CPU and advanced high performance multi-mode I/O,
designed for the system manufacturers, integrators, or VARs
that want to provide all the performance, reliability, and quality
at a reasonable price.
An advanced high performance super AT I/O chip SMC
FDC37C665 or ALI M5113 is used in the PSC-586VGA board.
Both on-chip UARTs are compatible with the NS16C550. The
parallel port and IDE interface are compatible with IBM PC/AT
and XT architecture's. The FDC37C665 or M5113 incorporates
sophisticated power control circuitry(PCC). The PCC supports
multiple low power down modes.
The on board VGA controller is Cirrus CL-GD54M30 graphics
accelerator. The VGA controller based on the internal PCI bus
to get the most high performance. User will not need extra
VGA card to release one PCI slot for other application.
In addition, the PSC-586VGA provides four 72-pin SIMM sockets for
its on-board DRAM. The 72-pin accepts 1MB, 2MB, 4MB, 8MB,
16MB, and 32MB SIMM. So, the total on-board memory can be
configured from 2MB to 128MB.
PSC-586VGA uses the ALI chipset, M1511/M1512/M1513,
which are 100% ISA/PCI compatible chipset.
4
1.1 Specifications :
The PSC-586VGA ISA/PCI Pentium w/ VGA Single Board Computer
provides the following specification:
•CPU : Pentium 75-166Mhz
•Bus : ISA bus and PCI 32-bit local bus
•DMA channels : 7
•Interrupt levels : 15
•Chipset : M1511/M1512/M1513
•Real-time clock/calendar : DS-12887 chip and quartz oscillator,
128B CMOS memory, powered by lithium battery for over 10 years
of data retention.
•RAM memory : 2MB to 128MB,EDO and standard DRAM supported
•Second Cache memory : 256KB/512KB/1MB Pipelined Burst and
Standard Cache RAM Module
•E-IDE hard disk drive interface : up to four PCI Ehnace IDE hard
drives.
•Floppy disk drive interface : two 2.88 MB, 1.44MB, 1.2MB, 720KB,
or 360KB floppy disk drives.
•Two high speed Series ports : NS16C550 compatible UARTs
•Bi-directional Parallel Port
•VGA Controller - GD54M30 :
Bus : PCI bus
Resolution : 1024x768 - 16 color(512KB VRAM)
256 color(1MB VRAM)
1280x1024 - 16 color(1MB VRAM)
Feature Connector : 26-pin hearder on board
5
•Watch-dog timer : can be set by 1,2,10,20,110 or 220 seconds
period. Reset or NMI was generated when CPU did not periodically
trigger the timer. Your program use hex 043 and 443 to control the
watch-dog and generate a system reset.
•Keyboard connector
•Mouse : PS/2 Mouse Port on-board.
•Power Consumption : +5V @ 4.2A ( Pentium-100,16MB EDO RAM)
±12V @ 15mA ( for RS-232 only)
•Operating Temperature : 0°~ 60°C ( CPU needs Cooler)
1.2 What You Have
In addition to this User's Manual, the PSC-586VGA package
includes the following items:
•PSC-586VGA ISA/PCI Pentium w/ VGA Single Board
Computer
•RS-232/Printer Cable
•FDD/HDD Cable
•VGA utility diskette
•6-pin Mini-Din to 5-pin Din Keyboard Adapter Cable
If any of these items is missing or damaged, contact the dealer
from whom you purchased the product. Save the shipping
materials and carton in case you want to ship or store the
product in the future.
6
2
Installation
This chapter describes how to install the PSC-586VGA. At first,
the layout of PSC-586VGA is shown, and the unpacking
information that you should be careful is described. The
jumpers and switches setting for the PSC-586VGA's
configuration, such as CPU type selection, system clock setting,
and watch dog timer, are also included.
2.1 PSC-586VGA's Layout
< reference next page >
7
2.2 Unpacking
8
Your PSC-586VGA Single Board Computer contains sensitive
electronic components that can be easily damaged by static electricity.
In this section, we describe the precautions you should take while
unpacking, as well as during installation. It is very important that the
instructions be followed correctly, to avoid static damage, and to
successfully install the board.
The system board should be done on a grounded anti-static mat. The
operator should be wearing an anti-static wristband, grounded at the
same point as the anti-static mat.
Inspect the cardboard carton for obvious damage. Shipping and
handling may cause damage to your board. Be sure there are no
shipping and handing damages on the board before processing.
After opening the cardboard carton, exact the system board and place
it only on a grounded anti-static surface component side up.
Again inspect the board for damage. Press down on all the socketed
IC's to make sure that they are properly seated. Do this only with the
board place on a firm flat surface.
Note : DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN
DAMAGED.
You are now ready to install your PSC-586VGA Single Board
Computer.
Indice
Altri manuali IEI Technology Computer a scheda singola
IEI Technology
IEI Technology NANO-KBN-i1 Manuale utente
IEI Technology
IEI Technology PCIE-Q370 Manuale utente
IEI Technology
IEI Technology KINO-DAL Manuale utente
IEI Technology
IEI Technology PSB-810EAV Manuale utente
IEI Technology
IEI Technology PCIE-9450 Manuale utente
IEI Technology
IEI Technology PM-PV-N4551/D5251 Manuale utente
IEI Technology
IEI Technology HYPER-AL series Manuale utente
IEI Technology
IEI Technology IMBA-8650 Manuale utente
IEI Technology
IEI Technology WAFER-ULT5 Manuale utente
IEI Technology
IEI Technology IMBA-H112 Manuale utente
IEI Technology
IEI Technology Rocky-3702EV Manuale utente
IEI Technology
IEI Technology WAFER-EHL-J6412 Manuale utente
IEI Technology
IEI Technology IMBA-H810 Manuale utente
IEI Technology
IEI Technology WAFER-945GSE Manuale utente
IEI Technology
IEI Technology PCIE-690AM2 Manuale utente
IEI Technology
IEI Technology KINO-780EB Manuale utente
IEI Technology
IEI Technology KINO-DH420 Manuale utente
IEI Technology
IEI Technology KINO-TGL-U Manuale utente
IEI Technology
IEI Technology NANO-7240 Manuale utente
IEI Technology
IEI Technology SPCIE-C236 Manuale utente
