IFM Electronic Efector 200 Manuale utente

Operating instructions

Diffuse reflection sensor with

background suppression

OGH7xx

704076 / 03 06 / 2011

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of pushbuttons, buttons or indications

→Cross-reference

Important note

Non-compliance can result in malfunctions or interference.

2 Safety instructions

According to the cULus approval

Caution - Use of controls or adjustments or procedures other than those specified

herein may result in hazardous radiation exposure.

Visible laser light; CLASS 1 LASER PRODUCT.

IEC 60825-1 : 2007

Complies with 21 CFR 1040.10 except for deviations pursuant to Laser

Notice No. 50, dated June 2007.

Position of the product label Additional label

3 Functions and features

The diffuse reflection sensor detects objects and materials without contact and

indicates their presence by a switching signal.

Range 20 ... 200 mm (on white paper 200 x 200 mm, 90 % remission)

4 Installation



1: LED

2: programming buttons

►Align the diffuse reflection sensor to the object to be detected.

►Secure it to a bracket.

Note:

The objects to be detected are to move transver-

sally to the lens of the sensor.

►In case of other directions of movement

it should be tested before whether safe

switching is guaranteed.

5 Electrical connection

The unit must be connected by a qualified electrician.

►The national and international regulations for the installation of electri-

cal equipment must be adhered to.

►Voltage supply according to EN 50178.

►Disconnect power.

►Connect the unit as follows:

DC PNP











pin 1 = L+ ( 10...36 V DC )

pin 3 = L-

pin 4 = load (200 mA)

(pin 2 = not connected)

DC NPN











pin 1 = L+ ( 10...36 V DC )

pin 3 = L-

pin 4 = load (200 mA)

(pin 2 = not connected)

6 Settings

6.1 The sensor is to switch when the object is detected

►Position the object





►Press [OUT on] for 2 s.

> The sensitivity is set to the object.

> The LED flashes.

►Remove the object





►Press [OUT off].

> The sensitivity is set without object.

> The LED goes out. The programming is finished.

6.2 The sensor is not to switch when the object is detected

►Position the object (see figure 1) and press [OUT off] for 2 s.

►Remove the object (see figure 2) and press [OUT on].

The setting can also be carried out first without object and then with object.

6.3 Setting of the maximum sensitivity

►Align the sensor so that no light is reflected.

The sensor is to switch when the object is detected

►First press [OUT on], then [OUT off].

The sensor is to switch when the object is not detected

►First press [OUT off], then [OUT on].

6.4 Programming unsuccessful

> The LED flashes quickly, 8 Hz.

• Measured value difference too small

• Max. programming time (15 min.) exceeded.

6.5 Electronic lock

Lock or unlock the buttons

►Press [OUT on] and [OUT off] simultaneously for 10 s.

> Acknowledgement is indicated by a change of the LED status.

7 Operation

►Check whether the unit operates correctly.

> The LED lights when the switching output is switched.

8 Maintenance, repair and disposal

►Keep the front pane of the sensor free from soiling.

►For cleaning do not use any solvents or cleaning agents which could damage

the plastic material.

►Do not try to open the module enclosure. There are no user - serviceable

components inside.

Technical data and further information at

www.ifm.com→Selectyourcountry→Datasheetdirect:

Altri manuali per Efector 200

Indice

Altri manuali IFM Electronic Accessori

IFM Electronic

IFM Electronic efector 200 OW Series Manuale utente

IFM Electronic

IFM Electronic efector 160 LK81 Series Manuale utente

IFM Electronic

IFM Electronic Efector 200 OM Series Manuale utente

IFM Electronic

IFM Electronic efector100 GG507S Manuale utente

IFM Electronic

IFM Electronic efector 250 Manuale utente

IFM Electronic

IFM Electronic efector 300 SU7200 Manuale utente

IFM Electronic

IFM Electronic efector 800 VSE100 Manuale utente

IFM Electronic

IFM Electronic Efector 150 KG5070 Manuale utente

IFM Electronic

IFM Electronic LR2759 Manuale utente

IFM Electronic

IFM Electronic efector230 UGA Manuale utente

IFM Electronic

IFM Electronic O1D105 Manuale utente

IFM Electronic

IFM Electronic ID000A Manuale utente

IFM Electronic

IFM Electronic LK8122 Manuale utente

IFM Electronic

IFM Electronic Efector 500 PL2058 Manuale utente

IFM Electronic

IFM Electronic efector 300 SU8200 Manuale utente

IFM Electronic

IFM Electronic Efector 100 series Manuale utente

IFM Electronic

IFM Electronic OGP Manuale utente

IFM Electronic

IFM Electronic Efector 500 PP70 Series Manuale utente

IFM Electronic

IFM Electronic efector 200 OJ50 Series Manuale utente

IFM Electronic

IFM Electronic LR8009 Manuale utente

IFM Electronic

IFM Electronic efector200 OGP50 Series Manuale utente

IFM Electronic

IFM Electronic LR3000 Manuale utente

IFM Electronic

IFM Electronic efector500 PI20 Manuale utente

IFM Electronic

IFM Electronic Efector 200 OGT1 Series Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manuale utente