IFM OGP7 Series Manuale utente
Operating instructions
Retro-reflective sensor
OGP7xx
80284283 / 00 04 / 2019
UK
2
1 Preliminary note
1.1 Symbols used
►Instruction
> Reaction, result
[…] Designation of pushbuttons, buttons or indications
→Cross-reference
Important note
Non-compliance can result in malfunctions or interference.
2 Safety instructions
According to the cULus approval
Caution - Use of controls or adjustments or procedures other than those specified
herein may result in hazardous radiation exposure.
Visible laser light; CLASS 1 LASER PRODUCT.
EN/IEC 60825-1 : 2007 and EN/IEC 60825-1 : 2014 complies with 21 CFR
1040 except for deviations pursuant to Laser Notice No. 50, dated June
2007
Position of the product label Additional label
3 Functions and features
In conjunction with a prismatic reflector or reflective tape the retro-reflective
sensor detects objects and materials without contact and indicates their presence
by a switching signal.
Range: www.ifm.com → Select your country → Data sheet direct: e.g. OGE700.
3
UK
4 Installation
1
1: LED
►Fit the prismatic reflector or the reflective tape behind the object to be detected.
►Align the retro-reflective sensor to it and secure it to a bracket.
Maximum range is only possible with precise alignment.
5 Electrical connection
The unit must be connected by a qualified electrician.
►The national and international regulations for the installation of electri-
cal equipment must be adhered to.
►Voltage supply according to EN 50178.
►Disconnect power.
►Connect the unit as follows:
DC PNP
pin 1 = L+ (10...36 V DC)
pin 3 = L-
pin 4 = load (200 mA)
(pin 2 = not connected)
4
6 Settings
6.1 The sensor is to switch when the object is detected
1
►Position the object.
►Press [OUT on] for 2 s.
> The LED flashes.
2
►Remove the object.
►Press [OUT off].
> The LED goes out. The programming is finished.
6.2 The sensor is not to switch when the object is detected
►Position the object (see figure 1) and press [OUT off] for 2 s.
►Remove the object (see figure 2) and press [OUT on].
The setting can also be carried out first without object and then with object.
6.3 Setting of the maximum sensitivity
►Align the sensor so that no light is reflected.
The sensor is to switch when the object is detected.
►First press [OUT on], then [OUT off].
The sensor is to switch when the object is not detected
First press [OUT off], then [OUT on].
6.4 Programming unsuccessful
> The yellow LED flashes quickly (8 Hz).
• Insufficient difference in measurements.
• Max. programming time (15 min.) exceeded.
5
UK
6.5 Electronic lock
Lock or unlock the buttons
►Press [OUT on] and [OUT off] simultaneously for 10 s.
> Acknowledgement is indicated by a change of the LED status.
7 Operation
►Check whether the unit operates correctly.
> The LED lights when the switching output is switched.
8 Maintenance, repair and disposal
►Keep the front pane of the sensor free from soiling.
►For cleaning do not use any solvents or cleaning agents which could damage
the plastic material.
►Do not try to open the module enclosure. There are no user - serviceable
components inside.
Technical data and further information at www.ifm.com
Indice
Altri manuali IFM Accessori
IFM
IFM KB Manuale utente
IFM
IFM TK61 Series Manuale utente
IFM
IFM SBT633 Manuale utente
IFM
IFM Efector 500 PNI02X Manuale utente
IFM
IFM MFH Manuale utente
IFM
IFM KI0058 Manuale utente
IFM
IFM PN72 Series Manuale utente
IFM
IFM VNB211 Manuale utente
IFM
IFM UGT204 Manuale utente
IFM
IFM LI513 Series Manuale utente
IFM
IFM efector 200 OGS38 Series Manuale utente
IFM
IFM SB4 Series Manuale utente
IFM
IFM LMT0 A Series Manuale utente
IFM
IFM OY90 S Series Manuale utente
IFM
IFM Efector 180 IX5030 Manuale utente
IFM
IFM Efector 200 O7E2 Series Manuale utente
IFM
IFM OF Series Manuale utente
IFM
IFM OG Manuale utente
IFM
IFM efector 200 O4P2 Series Manuale utente
IFM
IFM UGT203 Manuale utente
