INFOSEC E6 LCD 3000 RT Manuale utente

USER MANUAL

1000 / 2000 / 3000 VA

On-Line UPS

INFOSEC UPS SYSTEM – 4 rue de la Rigotière – 44700 Orvault – France – www.infosec-ups.com

Hot Line Tel : +33 (0)2 40 76 15 82 – fax : +33(0)2 40 94 29 51 – hotline@infosec.fr – 04 09 AA XX 201 18

Table of Contents

1IMPORTANT SAFETY INSTRUCTION ............................................................ 2

1.1. An Important Notice.................................................................................................................2

1.2. Storage Instruction...................................................................................................................2

2. PRODUCT INTRODUCTION........................................................................ 3

2.1 General Characteristics .............................................................................................................3

3. UPS FUNCTIONAL DESCRIPTIONS ............................................................ 4

3-1 UPS Front Panel Display Descriptions .........................................................................................4

3-2 Real Panel Descriptions.............................................................................................................6

3-3 Operating Modes & Voltage System Configurations......................................................................7

3-4 Communication Port Explanation................................................................................................9

4. INSTALLATION AND OPERATION............................................................ 10

4-1 Unpacking ............................................................................................................................. 10

4-2 Selecting Installation Position ................................................................................................. 10

4-3 Set up................................................................................................................................... 11

4.4. Operation .............................................................................................................................. 14

5. UPS WORKING PRINCIPLE...................................................................... 20

5.1. UPS System Block Diagram ..................................................................................................... 20

6. MAINTENANCE GUIDE............................................................................. 21

6.1. Trouble Shooting.................................................................................................................... 21

6.2. Error Codes and Their Descriptions .......................................................................................... 22

6.3. Maintenance .......................................................................................................................... 22

7. BUNDLE SOFTWARE INSTALLATION GUIDE............................................ 23

7.1. Hardware Installation.............................................................................................................. 23

7.2. Software Installation............................................................................................................... 23

8. OPTIONAL COMMUNICATION CARDS ..................................................... 23

8.1. R2E (2nd RS-232 ) card............................................................................................................ 23

8.2. USE (2nd USB) card................................................................................................................. 23

8.3. DCE (Dry Contact) card........................................................................................................... 24

8.4. SNMP Cards........................................................................................................................... 24

8.5. SNMP/WEB card..................................................................................................................... 24

8.6. SNMP card of Megatec............................................................................................................24

9. SPECIFICATIONS..................................................................................... 25

INFOSEC UPS SYSTEM – 4 rue de la Rigotière – 44700 Orvault – France – www.infosec-ups.com

Hot Line Tel : +33 (0)2 40 76 15 82 – fax : +33(0)2 40 94 29 51 – hotline@infosec.fr – 04 09 AA XX 201 18 2

1Important Safety Instruction

1.1.

An Important Notice

SAVE THESE INSTRUCTIONS - This Manual Contains Important Instructions that should

be followed during Installation and Maintenance of the UPS

Do not open the case, as there are no serviceable parts inside. Your Warranty will

be void.

Do not install the UPS in an environment with sparks, smoke or gas.

This UPS is equipped with an EMI filter. To prevent potential leakage current

hazard, ensure that the AC main supply is securely grounded.

This UPS is designed to be installed and commissioned in a sheltered, controlled

environment as follows:

oOperating temperature 0-40°C and 30-90% non-condensing humidity.

oAlways avoid contact with direct sunlight.

oInstalling the UPS in inflammable or hazardous environment.

oDusty, corrosive and salty environments can do damage to any UPS.

oInstall the UPS indoors as it is not designed for installation outdoors.

To prevent any overheating of the UPS, keep all ventilation openings free from

obstruction, and do not place anything on top of the UPS. Keep the UPS rear panel

20 cm away from the wall or other obstructions.

The battery will discharge naturally if the system is unused for any length of time.

Install the UPS away from objects that give off excessive heat and areas that are

excessively wet.

Always switch off the UPS and disconnect the batteries when relocating the UPS.

It should be recharged every 2-3 months if unused. If this is not done, then the

warranty will be null and void. When installed and being used.

Please ensure that the input voltage of the UPS matches the utility supply voltage.

Use a certified input power cable with the correct plugs and sockets for the

appropriate voltage system.

1.2.

Storage Instruction

For extended storage in moderate climate, the batteries should be charged for 12 hours

every 3 months interval by connecting the UPS to the utility supply and switch on input

breaker located at UPS rear panel. Repeat this procedure every 2 months if the storage

ambient temperature is above 30C.

INFOSEC UPS SYSTEM – 4 rue de la Rigotière – 44700 Orvault – France – www.infosec-ups.com

Hot Line Tel : +33 (0)2 40 76 15 82 – fax : +33(0)2 40 94 29 51 – hotline@infosec.fr – 04 09 AA XX 201 18

2. Product Introduction

2.1

General Characteristics

1. True online technology continuously supplies your critical device with a stable,

regulated, transient-free pure sine wave AC Power.

2. High Frequency Transformer-less technology with rack/tower convertible enclosure

enables the UPS for integration even in the most difficult of environment with

space constraints.

3. This UPS is equipped with fully digitalized control logic for greater functionality and

enhanced high level of power protection. Digital signal processing (DSP) also

provides the UPS with powerful communication capability, which enhances the

flexibility for easy remote control and monitoring

4. Wide input voltage tolerance from 60V ~ 144V (110V version) or 120V~288V

(220V version) allows under-voltage or over-voltage correction without

unnecessary battery drain and helps extend the battery life span.

5. DC-start function ensures the start-up of UPS even during power outages.

6. Revolutionary battery management circuit analyzes battery discharging status to

adjust battery cut-off point and extend the batteries’ life span.

7. Active Power Factor Correction (PFC) control function constantly maintains the UPS

Input Power Factor (PF) at > 0.99 for superb energy efficiency.

8. Selectable Bypass input voltage tolerance (Sensitivity low/high) to prevent under or

over voltage being supply to the loads at Bypass mode. The selectable Voltage

ranges are (i) Sensitivity Low: 90/180~130/260V & (ii) Sensitivity High:

97/194~130/260V.

9. Vast Selectable Output Voltages (100/110/115/120/127V or 200/208/220/230/240)

to meet various voltage systems.

10.The UPS is designed to comply with various stringent international standards for

Electromagnetic Interference & protection (EMC).

INFOSEC UPS SYSTEM – 4 rue de la Rigotière – 44700 Orvault – France – www.infosec-ups.com

Hot Line Tel : +33 (0)2 40 76 15 82 – fax : +33(0)2 40 94 29 51 – hotline@infosec.fr – 04 09 AA XX 201 18 4

3. UPS Functional Descriptions

3-1

UPS Front Panel Display Descriptions

LCD panel

LCD Display

Green LED steadily lights up to indicate that the Utility input voltage is within the

window (80Vac~144Vac, or 160Vac~288Vac); the LED flashes flickeringly to indicate

that the Utility input voltage is within the acceptable window (60Vac~79Vac, or

120Vac~159Vac).

, Green LED lights up to indicate there is an output available at the Programmable

Outlet 1 & Programmable Outlet 2.

Amber LED lights up to indicate the Bypass Input is normal.

UPS Fault LED

UPS On/Alarm Silence

UPS OFF Switch

Special functions log in/out

Go to next page

Go to previous page or change the setting of the UPS.

To re-confirm the change of UPS Setting

--> Manual Bypass：press " ON-KEY” and " Up-KEY" key simultaneously for

approx. 3 seconds to transfer from "Inverter to Bypass" ( the bypass led continuously

“blink“ and the buzzer will beep intermediately ) or "Bypass to Inverter", when the UPS

is on Line Mode and the Bypass Voltage Window is Normal.

INFOSEC UPS SYSTEM – 4 rue de la Rigotière – 44700 Orvault – France – www.infosec-ups.com

Hot Line Tel : +33 (0)2 40 76 15 82 – fax : +33(0)2 40 94 29 51 – hotline@infosec.fr – 04 09 AA XX 201 18

Symbols on the LCD Display Panel

Item Symbol Description

LINE

Utility or Bypass Source

2 Battery Low

3 Battery Abnormal

4 UPS Overloading

5 Site Wiring Fault

6 UPS Working in Service Mode

7 OFF UPS Shutoff

8 FAIL UPS Abnormal Lock

9 UPS Flow Chart

10 4 Digits Measurement Display

11 Indicate the item desired to be measured

12 Er05 Battery Weak or Dead

13 Er06 Output Short Circuit

14 Er10 Inverter Over-current

15 Er11 UPS Overheat

16 Er12 UPS Output Overloading

17 Er** Other Error Code

INFOSEC UPS SYSTEM – 4 rue de la Rigotière – 44700 Orvault – France – www.infosec-ups.com

Hot Line Tel : +33 (0)2 40 76 15 82 – fax : +33(0)2 40 94 29 51 – hotline@infosec.fr – 04 09 AA XX 201 18 6

3-2

Real Panel Descriptions

1. USB Port

2. RS232 Port

3. Emergency Power Off (EPO) Dry Contact Signal inputs

4. Communication Card Options Slot

5. External Battery Connector

6. AC power connection socket

7. AC Outlets

8. Two programmable outlets

9. Utility Input circuit breaker

10. Cooling Fans

11. Output circuit breaker for two outlets

12. Output circuit breaker for two programmable outlets

INFOSEC UPS SYSTEM – 4 rue de la Rigotière – 44700 Orvault – France – www.infosec-ups.com

Hot Line Tel : +33 (0)2 40 76 15 82 – fax : +33(0)2 40 94 29 51 – hotline@infosec.fr – 04 09 AA XX 201 18

3-3

Operating Modes & Voltage System Configurations

Download and open the “UPS Setting Tool” Software to see the screen as below

System Configuration Settings

1. System Voltage Selection：Select Input Voltage

110V or 220V

2. Voltage Configurations：Select UPS Output

Voltage 200V/208V/220V/230V/240V or

100V/110V/115V/120V/127V

3. UPS Modes：Select Normal/CF50*/CF60* Mode

4. Output Voltage Fine Tuning：Output Voltage

Regulation from 0～±3%

5. Bypass Voltage Windows：Sensitivity: Select

Sensitivity Low/Sensitivity High**

Sensitivity Low Sensitivity High

110V 90V～130V 97V～130V

220V 180V～260V 194V～260V

6. Syn-Frequency Window：Select 3Hz/1Hz Inverter Freq synchronizing range

7. Com Port：Select the Com Port of PC

8. Click on “Write” to confirm the configuration settings. The UPS will beep twice to

acknowledge setting is successful.

9. Turn off the UPS and unplug input power cord from AC Power Utility receptacle to

shutdown whole unit without internal power supply existing, after setting is

complete. 3 seconds later reconnect input power cord into AC Power Utility

receptacle and turn on the UPS, referring to the section 4.4 Operation. The UPS will

perform in new settings.

Note: *CF50/CF60 = Frequency Converter mode 50 to 60Hz or vice versa

**Sensitivity Low: 90/180~130/260V

Sensitivity High: 97/194~130/260V

INFOSEC UPS SYSTEM – 4 rue de la Rigotière – 44700 Orvault – France – www.infosec-ups.com

Hot Line Tel : +33 (0)2 40 76 15 82 – fax : +33(0)2 40 94 29 51 – hotline@infosec.fr – 04 09 AA XX 201 18 8

Programmable outlet setting

The UPS is equipped with 2 programmable outlets

for use to supply to less critical loads. These outlets

can be disabled to shed the less critical loads during

back-up modes or overload conditions to maintain

quality power supply to the more critical loads

connected to the UPS.

Click on the “Programmable outlet setting” bar to

enter to the setting screen as shown below.

1. Outlet Turn On After Turn on UPS –

select the

time to automatically enable this outlet within

the specified time when the UPS is powered

on. If “0” sec is selected, the outlet will be

enabled once the UPS is powered on

2. Outlet Turn Off After AC Failure –

select this option to automatically disable the

outlet within the specified time after utility outage to shed the less critical loads to

provide longer battery back-up time for the other more critical loads connected to

the UPS.

3. Outlet Turn On After AC Recovered –

select this option to automatically enable the

outlet within the specified time after the utility is restored.

4. Outlet Turn Off When Battery Lower than -

select this option to automatically

disable the outlet at the specified remaining battery power capacity(%) during

battery mode to shed the less critical loads to prolong battery back-up time for the

other more critical loads connected to the UPS.

5. Outlet Turn Off When Overload –

select this option to automatically disable the

outlet during overload condition (bypass mode) to possibly allow the more critical

loads:

To be continually supplied via Bypass without shut down

6. You have to select the "Setting" menu to configure new parameters. The

calibration is confirmed successfully after the UPS beeps twice. Turn off the UPS

and unplug input power cord from AC Power Utility receptacle to shutdown whole

unit without internal power supply existing, after setting is complete. 3 seconds

later reconnect input power cord into AC Power Utility receptacle and turn on the

UPS, referring to the section 4.4 Operation. The UPS will perform in new settings.

7. Manual Control Switch – Click “On” or “Off” to manually enabled or disabled the

programmable outlets, overriding all previous settings

INFOSEC UPS SYSTEM – 4 rue de la Rigotière – 44700 Orvault – France – www.infosec-ups.com

Hot Line Tel : +33 (0)2 40 76 15 82 – fax : +33(0)2 40 94 29 51 – hotline@infosec.fr – 04 09 AA XX 201 18

3-4

Communication Port Explanation

The UPS is equip with EPO dry contacts input, true RS232 & USB Communication port as

standard to provide communication with bundled UPS monitoring software for remote

monitoring of UPS status via PC.

There are 4 other optional interface cards available to meet various communication needs,

i.e. DCE (dry contact relay card), R2E, USE and SNMP/WEB card (Please consult Ch8).

The bundled software of the UPS is compatible with many operating systems such as

Windows 98, & 2000, ME, NT and XP. For other applications such as Novell, NetWare,

UNIX, Linux, please contact your local dealer for suitable software.

All the communication ports (including optional cards) can be active & use simultaneously

to monitor the UPS status. However only 1 communication interface at any one time with

the highest priority has the ability to command & control the UPS. The priority of these

communication interfaces are as follow:

Highest Priority (in descending order),

1) EPO input port

2) Optional Interface card

3) USB

4) RS232

True RS232 Port interface descriptions

Baud Rate 2400 bps

Data Length 8 bits

Stop Bit 1 bit

Parity None

The Pin Assignments of the true RS232 port are illustrated as follows：

Pin 3 RS232 Rx

Pin 2 RS232 Tx

Pin 5 Ground

EPO

The Pin assignments of the EPO Input port are:

1 EPO+

2 Ground

To enable the EPO function, please short Pin 1 & 2.

1 2

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali INFOSEC UPS

INFOSEC

INFOSEC XP OFFICE 1000 VA Manuale utente

INFOSEC

INFOSEC E4 700 VA Manuale utente

INFOSEC

INFOSEC 5000 VA Manuale utente

INFOSEC

INFOSEC Zen-X Series Manuale utente

INFOSEC

INFOSEC Z1 Zenergy Cube 400 VA Manuale utente

INFOSEC

INFOSEC E6 LCD 10K TM RM Manuale utente

INFOSEC

INFOSEC E3 Pro RT Manuale utente

INFOSEC

INFOSEC X4 RM PLUS Series Manuale utente

INFOSEC

INFOSEC E3 LCD-RT Manuale utente

INFOSEC

INFOSEC E4 LCD Pro Series Manuale utente

INFOSEC

INFOSEC R1 USB 600 Manuale utente

INFOSEC

INFOSEC E6 LCD RT EVOLUTION (S) 1000 Manuale utente

INFOSEC

INFOSEC HERO PRO DUAL PLUG 700 Manuale utente

INFOSEC

INFOSEC Z4 B-box 500 VA Manuale utente

INFOSEC

INFOSEC PFS Tel 1 GE Manuale utente

INFOSEC

INFOSEC E4 LCD Pro Series Manuale utente

INFOSEC

INFOSEC Zenergy Station 2000 Manuale utente

INFOSEC

INFOSEC E3 PRO 1000 RM Manuale utente

INFOSEC

INFOSEC SMART LINE 1000 VA Manuale utente

INFOSEC

INFOSEC E4 Value Series Manuale utente

INFOSEC

INFOSEC XP PRO UPS 1000 VA Manuale utente

INFOSEC

INFOSEC E4 LCD 3000 Manuale utente

INFOSEC

INFOSEC E6 LCD-RT Manuale utente

INFOSEC

INFOSEC Hero Pro Dual Plug 700 VA Manuale utente

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente