Initiative Engineering STM40FF Manuale utente

Take a 25NB Rigid PVC Riser pipe, longer than the height of the vessel and solvent cement the boom distributor to one end of the pipe.Insert this riser pipe into the vessel and cut the pipe from the top ensuring that the height of the pipe (with the distributor touching the boom) is 42mm more than the top of the vessel.Pour RESIN into the vessel. Cover the mouth of the riser pipe while doing this so that resin doesn't enter the pipe. Align the riser pipe so that it is in the centre of the vessel opening.Screw on the top distributor to the boom of the MPV.Screw on the MPV to the vessel ensuring that the riser pipe goes through the top distributor into the MPV. Connect the sucon ﬁlter assembly to the ejector sucon nozzle aer ﬁng a ¾" valve on the sucon elbow of the MPV.Put the sucon ﬁlter into the Brine tank ensuring that the sucon ﬁlter always remain vercal. You can cut the supplied tubing to the correct length so that the tubing always remain taut and does not loop. Alternavely the sucon ﬁlter can be inserted in a 3" PVC pipe (with slot at the boom) which is clamped to the Brine tank.Make the Inlet, Outlet and Drain connecons.Sr. No. 273, Near Vitthal Mandir, Bhatewara Nagar,Hinjawadi, Pune - 411 057, Maharashtra (India)Tel.:+91 20 2293 2122, +91 20 2293 2123E-MAIL:inf[email protected]om www.initiativeengineering.com1. Mulport valve 2. Top and Boom DistributorSPECIFICATIONSSCOPE OF SUPPLYGENERAL ASSEMBLYMULTIPORT VALVE STM40FF

INSTALLATION

Inlet/Outlet/ Drain connecons 1.5” BSPValve Threading for Vessel Mounng 2.5" NPSMFlow Rate 6m³/hr @0.5kg/ cm² Max. Operang Pressure 5kg/ cm²Ejector Sucon at 2kg/ cm² 750LphEjector Rao 1:11.2.3.4.5.6.7.:::::::Brine Line3/4" BSP3. O & M ManualFRONT VIEWSIDE VIEW344DRAININLET1753535

115112

3545

150

90142

307

167

Always press the handle down before turning the handle to the desired posion viz. Service, Regeneraon or Rinse.If the line pressure is more, It is advisable to close the inlet valve before turning handle.Ensure that minimum 2kg/cm² pressure is available for geng opmum ejector performance.If there is a sucon problem even at 2kg/cm² then the ejector may be clogged with dirt etc. For cleaning this, remove the ejector by unscrewing it from the MPV, clean and put back.

OPERATION

NOTE: You can also ﬁll the RESIN in the vessel ﬁrst and also ﬁll some water in it. Then follow the procedure of cemenng boom distributor, cung correct length of riser pipe, ﬁxing top distributor to MPV and then pushing the riser pipe through the top distributor into the MPV. Now this MPV with aached riser pipe can be pushed into the vessel and screwed on the top.123456781234

P16P12P10

P14

P15P13

Top DistributorBoom DistributorSucon ElbowRiser Pipe Adaptor ‘O’ Ring (31.5X3.2)Lower Housing ‘O’ Ring (65X4.5)Union Assembly ‘O’ Ring (44X3)Drain Elbow Assembly washer (38x45x2.5)Ejector ‘O’ Ring (16X2.2)Ejector Knob Oval Ring (21X28X2.5)Sucon Nozzle ‘O’ Ring (13.2X2.1)28.29.30.31.P15P16R9R10

Altri manuali Initiative Engineering Unità di controllo