Inlog PC-482VN Series Manuale utente

PC-482VN series

Embedded STPC ATLAS 5x86DX2-133

PC/104 CPU Module with on-board

VGA/LAN/CF/TFT LCD interface

and

General Purpose I/O channels

Copy Right Notice

The information in this manual is subject to change without prior notice in order t o improve

reliability ,design and function and dosed not represent a commitment on the part of the

manufacturer. No part of this manual may be reproduced, copied, or transmitted in any

form without the prior written permission of manufacturer.

Acknowledgment

Products mentioned in this manual are mentioned for identification purpose only. Products

manes appearing in this manual may or may not be registered trademarks or copyright of

their respective companies

Edition: 1.02 Printed July. 2003

http:/www.inlog.com.tw

Table of contents

Chapter 1Hardware installation.............................5

1.1 Introductions 6

1.2 Packing list 6

1.3 Specifications 7

Chapter 2Jumper settings .....................................9

Locating jumpers 10

2.1 CompactFlash Slot on solder side 11

2.2 Jumper Setting 12

2.3 Setting jumpers 12

2.3.1 COM1 RS-232/RS-422/RS-485 Selection ( JP1 ) .............13

Chapter 3Connecting Peripherals.........................14

3.1 Locating Connectors 15

3.2 Connectors Summary 16

3.3 Hardware reset switch (CN3) 17

3.4 Keyboard & PS/2 mouse connector (CN7) 17

3.5 Hard disk LED (CN13) 17

3.6 Floppy drive connector (CN2) 18

3.7 IDE Hard Drive Connector (CN9) 19

3.8 Parallel port connector (CN5) 20

3.9 Serial port connectors (CN10, CN8) 21

3.10 General Purpose I/O Connector(GPIO) (CN6) 22

3.11 CPLD Connector (CN4) 23

3.12 CRT display connector (CN1) 23

3.13 Flat panel display connector (CN11) 24

3.14 USB1 & USB2 connector (CN12) 25

3.15 Speaker Connector (CN14) 25

3.16 Ethernet 10/100 Base-T connector (CN15) 25

3.17 External “+12VDC / +5VDC” power input connector (CN16) 26

3.18 External “-12VDC / -5VDC” power input connector (CN17) 26

3.19 CompactFlash Slot (CN18) 27

Chapter 4VGA BIOS Setup.....................................28

Introduction 29

4.1.1 Chipset 29

4.1.2 Display memory.................................................................29

4.1.3 Flat Panel BIOS and Utility ................................................29

Appendix AFlash Disk Setup & EEPROM R/W..30

Appendix BProgramming Watch dog timer ......33

Appendix CAward BIOS Setup...........................35

Appendix DProgramer’s Reference...................47

Appendix ESystem configuration......................52

Hardware installation

Chapter 1

Hardware installation

1.1 Introductions

The PC-482VN is a full-function PC/104 CPU Module which integrates the VGA/TFT

LCD panel, CompactFlash,GPIO,Ethernet(PC-482VN Only) and other enhanced I/O

interfaces on a PC/104 CPU Module. This Module uses an embedded SGS-THOMSON

STPC ATLAS Pentium performance x86-133 low power CPU and embedded 32MB

SDRAM on board

The PC-482VN offers power management to minimize power consumption. It complies

with the "Green Function" standard and supports three power saving features: doze,

sleep, and suspended mode.

Its high performance VGA display supports both CRT and TFT LCD displays with a

Display Memory UMA architecture, share system memory up to 4MB and a resolution of

up to 1024x768(CRT).

The PC-486V also offers several industrial features such as a 255-level watchdog timer

with jumperless setup, supports M-systems DiskOnChip Flash Disk,CompactFlash

Slot,GPIO and PC/104 connection for additional functions with PC/104 modules.

1.2 Packing list

 One PC-482VN PC/104 CPU Module

 One Quick Installation Guide

 One CD-ROM for manual (in PDF format), drivers and utility

 One 2mm to 2.54mm IDE flat cable, 44-pin to 40-pin

 One 2mm to 2.54mm FDD cable (34-pin)

 One 2mm to 2.54mm parallel port adapter (26-pin) kit

 One 2mm to 2.54mm serial port(COM1) adapter (10-pin) kit

 One 2mm to 2.54mm 1 to 3 serial port(COM2,3,4) adapter (10-pin) kit

 One Ethernet RJ-45 connector Conversion (For PC-482VN only)

 .One USE cable for two USB port

 One 6-pin DIN to two 6 pin mini-DIN for keyboard,PS/2 Mouse adapter

Hardware installation

1.3 Specifications

 System Chipset :

The STPC ATLAS chipset integrates a fully static 5x86-133MHz low power processor,

fully compatible with standard x86 processors, and combine it with powerful chipset,

graphics and video pipelines to provide a single consumer oriented PC compatible

subsystem. The performance of this device is comparable with the performance of a

typical P5 generation system.

The STPC ATLAS includes a powerful x86 processor core along with a 64-bit DRAM

controller, advanced 64-bit accelerated graphics and video controller, a high speed

PCI chip set functions

Graphics functions are controlled through the on-chip graphic engine in the STPC

ATLAS and the monitor (or TFT)display is produced through 2D graphics display

engine. The graphics resolution supported is a maximum of 1024x768 at 75 Hz refresh

rate and is VGA and SVGA compatible

 System Memory: On-board 32MB SDRAM(up to 64MB)

 Bus interface: PC/104 ISA bus

 Multi I/O : Winbond W83977F

 System BIOS: Award PnP BIOS with VGA BIOS in a single 256KB FLASH ROM

(Year 2000 Compliant BIOS)

 Plug and Play: Dual interrupt and DMA signal steering with plug and play control.

 Display:

 Graphics functions are controlled through the on-chip graphic engine in the

ST PC ATLAS Chipset

 The CRT graphics resolution supported is a maximum of 1024x768 at 75 Hz

refresh rate and is VGA and SVGA compatible

 Flat Panel Display: Supports 9/12/18-bit TFT flat panels with resolution up to

800 x 600

 LAN: RTL8139C PCI local bus single-chip Fast Ethernet controller and RJ-45

connector. supports 10 Mb/s and 100 Mb/s N-way Auto-negotiation operation

(LAN for PC-482VN only)

 Floppy Disk Drive Interface: Supports Up to two Floppy Disk Drives,5.25"(360KB or

1.2MB) and/or 3.5"(720KB or 1.44MB/2.88MB)

 IDE Hard Disk Drive Interface: One Channel Ultra-DMA 33MB/sec PCI EIDE

Hardware installation

 CompactFlash Slot: One Fully IDE CompactFlash Type I/II Compatibility Slot and

Support +5VDC or +3.3VDC IDE CompactFlash Card. (CF for PC-482VN only)

 Serial Ports:

 Three RS-232C and One RS-232/422/485 serial Ports. For PC-482VN

(One RS-232C and One RS-232/422/485 serial Ports. For PC-482V)

 Overvoltage protection for RS-422/485 up to 25kV

 All with 16C550 UART And 16 byte FIFOs

 Printer Port: One SPP/ECP/EPP Bi-direction Parallel Port.

 Solid state disk: One expended 32-pin Sockets for M-Systems DiskOnChip

 EEPROM : Provide 256 words(16 bit) EEPROM register for user

 Real-time clock/calendar: Lithium battery with 10 year data retention

 General Purpose I/O interface:

 Provide 16 channels TTL level General Purpose I/O interface

 Each channel can be software programmed to be input or output

 Individual software programmable interrupt mask.

 Watch Dog timer: The watch dog timer range from 0 to 254 sec

 I/O bus expansion: PC/104 ISA Bus connector

 Power Supply Voltage: + 5VDC

 Power Consumption: +5VDC/1.6A (max)

 Operating Temperature: 32 to 140F (0 to 60C).

 Dimensions: 96(L) x 90(W)mm

Jumper settings

Chapter 2

Jumper settings

Locating jumpers

Jumper settings

2.1 CompactFlash Slot on solder side

Jumper settings

2.2 Jumper Setting

The PC-482VN has a number of jumper that allow you to configure your system to suit

your application. The table below lists thefunction of each of the board’s

jumper:

Label Function

JP1 COM1 RS-232/422/485 selection Ref. 2.3.1

2.3 Setting jumpers

You configure your card to match the needs of your application by setting jumpers. A

jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal

clip (often protected by a plastic cover) that slides over the pins to connect them. To

<close> a jumper you connect the pins with the clip. To <open> a jumper you remove the

clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3. In this case you would

connect either pins 1 and 2 or 2 and 3.

The jumper settings are schematically depicted in this manual as follows:

A pair of needle-nose pliers may be helpful when working with jumpers.

If you have any doubts about the best hardware configuration for your application, contact

your local distributor or sales representative before you make any changes.

The Jumper settings with background color are factory default

Jumper settings

2.3.1 COM1 RS-232/RS-422/RS-485 Selection ( JP1 )

The COM1 port can be selected as RS-232, RS-422 or RS-485 by

setting JP1. The following chart shows the jumper setting.

JP1 COM1 Type

ALL OPEN for RS-232C

(Default)

ALL CLOSED for RS-422/485

Connecting Peripherals

Chapter 3

Connecting Peripherals

3.1 Locating Connectors

Connecting Peripherals

3.2 Connectors Summary

On-module connectors link the PC-482VN to external devices such as hard disk drives, a

keyboard, or floppy drives. The table below lists the function of each of the board’s

connectors:

Label Function Page

CN1 CRT Display connector 3.12

CN2 FDD connector 3.6

CN3 Reset connector 3.3

CN4 CPLD connector 3.11

CN5 Parellel port connector 3.8

CN6 General Purpose I/O connector 3.10

CN7 Keyboard & PS/2 mouse connector 3.4

CN8 Serial Port 2,3,4 (COM2/3/4) connector 3.9

CN9 Hard disk connector 3.7

CN10 Serial Port 1 (COM1) connector 3.9

CN11 Flat panel disply Connector 3.13

CN12 USB connector 3.14

CN13 Hard disk LED 3.5

CN14 Speaker connector 3.15

CN15 Ethernet connector 3.16

CN16 +12V/+5V External Power Input connector 3.17

CN17 -12V/-5V External Power Input connector 3.18

CN18 CompactFlashSlot 3.19

Connecting Peripherals

3.3 Hardware reset switch (CN3)

The hardware reset switch button is an active low signal (24 mA sink rate).

Pin Function

1 Reset SW -

2 Reset SW +

3.4 Keyboard & PS/2 mouse connector (CN7)

The PC-482VN module provides a keyboard connector. The standard PC/AT BIOS will

report an error or fail during power-on self-test (POST) after a reset if the keyboard is not

present. The PC-482VN’s BIOS standard setup menu allows you to select “All, But

Keyboard” under the <Halt On> selection. This allows no-keyboard operation in embedded

system applications without the system halting under POST.

The PC-482VN module also provides PS/2 mouse connectors, which can be connected to

outside world with convert cable.

pin Signal

1 KBD_CLK

2 KBD_Data

3 MS_CLK

4 GND

5 +5V/DC

6 MS_Data

3.5 Hard disk LED (CN13)

The hard disk LED indicator for hard disk access is an active low signal (24 mA sink rate).

Pin Function

1 LED -

2 LED +

Connecting Peripherals

3.6 Floppy drive connector (CN2)

You can attach up to two floppy drives to the PC-482VN’s on-board controller. You can use

any combination of 5.25” (360 KB and 1.2 MB) and/or 3.5” (720 KB, 1.44 MB, and 2.88 MB)

drives.

1. Plug the 34-pin flat-cable connector into CN2. Make sure that the red wire

corresponds to pin one on the connector.

2. Attach the appropriate connector on the other end of the cable to the floppy drive(s).

You can use only one connector in the set. The set on the end (after the twist in the

cable) connects to the A: drive. The set in the middle connects to the B: drive.

Pin Signal Pin Signal

1 GND 2 DENSITY SELECT*

3 GND 4 N/C

5 GND 6 DRIVE TYPE

7 GND 8 INDEX*

9 GND 10 MOTOR 0*

11 GND 12 DRIVE SELECT 1*

13 GND 14 DRIVE SELECT 0*

15 GND 16 MOTOR 1*

17 GND 18 DIRECTION*

19 GND 20 STEP*

21 GND 22 WRITE DATA*

23 GND 24 WRITE GATE*

25 GND 26 TRACK 0*

27 GND 28 WRITE PROTECT*

29 GND 30 READ DATA*

31 GND 32 HEAD SELECT*

33 GND 34 DISK CHANGE*

* low active

Connecting Peripherals

3.7 IDE Hard Drive Connector (CN9)

Connect one end of the cable to CN9. Make sure that the red (or blue) wire corresponds

to pin 1 on the connector, which is labeled on the board (on the right side).

Pin Signal Pin Signal

1 -RST 2 Ground

3 D7 4 D8

5 D6 6 D9

7 D5 8 D10

9 D4 10 D11

11 D3 12 D12

13 D2 14 D13

15 D1 16 D14

17 D0 18 D15

19 GND 20 N.C

21 N.C 22 GND

23 IOW 24 GND

25 IOR 26 GND

27 IORDY 28 BALE

29 N.C. 30 GND

31 IRQ 32 IO16

33 A1 34 N.C.

35 A0 36 A2 CS0

37 CS0 38 CS1

39 -LED 40 GND

41 +5VDC 42 +5VDC

43 GND 44 NC

Connecting Peripherals

3.8 Parallel port connector (CN5)

Normally, the parallel port is used to connect the card to a printer. The PC-482VN includes

a multi-mode (ECP/EPP/SPP) parallel port, accessed through CN5, a 26-pin flat-cable

connector. You will need an adapter cable if you use a traditional DB-25 connector. The

adapter cable has a 26-pin connector on one end and a DB-25 connector on the other.

The parallel port is designated as LPT1 and can be disabled or changed to LPT2 or LPT3

in the system BIOS setup. The parallel port interrupt channel is designated to be IRQ7.You

can select ECP/EPP DMA channel via BIOS setup.

Pin Signal Pin Signal

1 STROBE 2 AUTOFD*

3 D0 4 ERR

5 D1 6 INIT*

7 D2 8 SLCTINI*

9 D3 10 GND

11 D4 12 GND

13 D5 14 GND

15 D6 16 GND

17 D7 18 GND

19 ACK* 20 GND

21 BUSY 22 GND

23 PE 24 GND

25 SLCT 26 N/C

Indice

Altri manuali Inlog Computer a scheda singola

Inlog

Inlog PI-6582V Manuale utente

Manuali Computer a scheda singola popolari di altre marche

WIN Enterprises

WIN Enterprises PL-80910 Manuale utente

AXIOMTEK

AXIOMTEK SBC81206 Series Manuale utente

Embest

Embest SOM-PH8800 Manuale utente

SeaLevel

SeaLevel SBC-R9 Manuale utente

SMART Embedded Computing

SMART Embedded Computing ATCA-8310 Manuale utente

WinSystems

WinSystems PPM-LX800-G Manuale utente

GIGAIPC

GIGAIPC QBiX-PPC Series Manuale utente

OLIMEX

OLIMEX A10S-OLinuXino-MICRO Manuale utente

Commell

Commell FS-978 Manuale utente

GIGAIPC

GIGAIPC QBiP-8665A/ Manuale utente

VersaLogic

VersaLogic Python EBX-11 Manuale utente

Micro Computer Specialists

Micro Computer Specialists IRV-3702 Manuale utente

CompuLab

CompuLab SB-A510 Manuale utente

Boser

Boser HS-7321 Manuale utente

Premier Farnell

Premier Farnell Embest SBC8530 Manuale utente

MicroSys Electronics

MicroSys Electronics miriac SBC-LS1043A2 Manuale utente

Aaeon

Aaeon UP Manuale utente

Portwell

Portwell WUX Series Manuale utente