Intact BATTERY GUARD Manuale utente

USER MANUAL

EN FR IT ES

16-301-15 31-45 46-60

2 3

The product is used to monitor the car battery,

starting system and charging system. After the

device is connected to the battery, it can be

connected to your smartphone via Bluetooth

5.3. When problems occur with the battery,

starting or charging system occur, it can send

a notification to the user. Besides, the user can

also record his travelled distance. This product

is compatible with all 12V lead-acid and lithium

batteries.

Table of contents

1.0 Information about the procuct ....................................................... page 4

2.0 Safety instructions .............................................................................. page 4

3.0 Installation instruction ...................................................................... page 4

4.0 App installation ..................................................................................... page 5

4.1 Bluetooth radius ................................................................................... page 5

4.2 App operation ........................................................................................ page 6

4.3 Cranking Test .......................................................................................... page 10

4.4 Loading test ............................................................................................ page 11

4.5 Overview of trips .................................................................................. page 13

4.6 Settings ..................................................................................................... page 14

5.0 Further notes .......................................................................................... page 15

4 5

（Fig 1 ）

Average power

consumption 0,534 mA (Bluetooth not connected)

1,7 mA (Bluetooth connected)

Input voltage 6~19V

Operating temperature -30 bis +80 °C (-22 bis +176 °F)

Dimensions 63*45*13mm (L*W*H)

Measurement accuracy ±0.03V

Short circuit protection Built-in

Reverse Polarity Protection Built-in

Bluetooth-Version 5.3

Bluetooth Name Battery Guard

App Name intAct Battery-Check

2.0 Safety instructions

The product housing and cables are made of fireproof materials and are suitable for high temperatures.

There is a built-in safety switch to prevent short-circuits, which automatically switches off the device

as soon as the current is too strong. Also, reverse polarity protection is built in, so in case of reverse

polarity, there will be no damage to the battery, vehicle or device.

1.0 Information about the product

3.0 Installation instruction

1. Attach the red connector to the positive

terminal and the black connector to the

negative terminal and tighten the screws.

2. Attach the device to the battery housing

with the supplied double-sided adhesive

tape. Clean the surface before taping..

E13

Download the app before using the device.

To do so, scan the QR code on the product or

packaging or search for „intAct Battery Check” in

the App Store or Google Play Store..

4.1 Bluetooth radius

As long as there are no obstacles or other interference factors between the device and your

smartphone, the Bluetooth connection between the device and the app will remain within a radius of

up to 10 meters. If there are obstacles or other interfering factors within this radius, this may affect

the connection and reduce the connection radius.

10m 10m

4.0 App installation

6 7

4.2-1

Click on the app icon, run the app and turn on the

Bluetooth of your smartphone.

4.2-2

Please allow the app to access the location even if

you are not using the app.

If you do not, the product will not automatically

notify the user when a problem is detected on the

battery.

4.2-3

Please allow to receive notifications.

Then the device will send you notifications re-

garding the car battery, start system and prob-

lems. These notifications will be sent when your

smartphone is within the Bluetooth radius of the

device.

4.2-4

To add a device, it is necessary to enter the serial

number of the device, which can be scanned by

barcode or entered manually. The serial number

incl. barcode can be found on the subpage of

the device and on the page of the device. Please

select the battery type and name the device for

better recognition.

Notice:

The app supports multiple devices, and

up to four devices can be displayed in the

app at the same time. You can also click

the „Edit“ icon or the „Delete“ button to

rename or delete the device.

4.2 App operation4.2 App operation

8 9

1. Here you can edit the device name and

assign an individualized name to your

Battery-Guard.

2. If the device is connected to the app,

the Bluetooth icon will turn blue, if the

connection is lost, it will turn red. By default,

the app automatically connects to the

device as soon as it is within Bluetooth

range.

Here you can add a new device or select the

one to be displayed from the already added

devices. Up to four devices can be displayed

at the same time.

4. Battery charge level in percent.

5. The color of the ring changes according to

the battery charge level.

6. Battery status display: battery OK (yellow),

battery charging (blue), low battery (red).

7. Display of battery voltage in real time.

8. Display of battery case temperature in real

time.

9. Access to the start test interface. Every time

the engine starts, a start test is performed

automatically.

10. Access the charging test interface and test

the charging system manually.

910

12 13 14 15

11.

Battery voltage graph: click on the graph to

enlarge it. The graphic shows you either the

state of charge in %, the temperature or the

battery voltage in volts. Here you can choose

between the display of one day, 3 or 5 days.

You can also switch between the days at the

top center.

12. Start screen

13. Overview of your trips

14. Device list

15. Settings

4.25 Basic function start page

10 11

1. Engine start time

2. Starter test: When the engine starts, the

device automatically tests the starting

system and stores the test result. If the

voltage is higher than 9.6 V when starting,

it is considered normal. However, if the

starting voltage is below 9.6 V, this indicates

a defect. This may mean that the battery is

too weak due to lack of charge, aging or

other factors, the starter motor is defective

or there is some other problem.

3. Starting voltage indicator. Green indicates a

normal value, red indicates too low starting

voltage.

4. Graphic display of the starting voltage.

1. Start test

2. For the test of the open circuit voltage,

please leave the vehicle in idle, switch on all

electrical consumers. The test takes about 6

seconds.

3. For high speed voltage test, please turn off

all electrical consumers, increase the speed

to 2500-3000/min and hold it for 6 sec-

onds. Then the test is finished.

4. For the diode ripple test, please let the ve-

hicle run in the idle, turn off all electrical

electrical devices off. This test will take 6

seconds.

4.3 Cranking test 4.4 Load test

12 13

5. Help screen to interpret the results:

Charging voltage normal: Charg-

ing system indicates alternator out-

put is normal, no problem detected.

Charging voltage too low: Check if the

drive belt is slipping or check if the line

connection between alternator and bat-

tery is normal or not. If the drive belt and

lead connection are OK, please follow

the vehicle manufacturer‘s recommen-

dations to rule out alternator failure.

Charging voltage too high: The output

voltage of the alternator is too high. Please

contact a specialist workshop to check the

charging device. The usual voltage for au-

tomotive regulators is 14.7 ±0.5 V. High

charging voltage will overcharge the battery

and shorten its life, also it may cause mal-

function.

6. Time of the end of the charge test.

7. Open circuit voltage: Green means normal,

red indicates too high or too low voltage.

8. Voltage at higher speeds: Blue means nor-

mal, red indicates voltage is too high or too

low.

9. Diode ripple test: Orange means normal, red

indicates too high or too low.

10. Here you can repeat the test.

1. Click the icon to view the trip logs of each

month or all.

2. Select a specific device to view the trip data.

Start time, operation time and misfire time of

each ride.

4.4 Load test 4.5 Overview of trips

14 15

1. Daily notification: Blue is on, white is off.

The system default is no more than one

notification in 9 hours, the notification fre-

quency can be adjusted.

2. Abnormal startup notification: Blue is on,

white is off. The system default is no more

than one notification in 9 hours, the notifi-

cation frequency can be

3. Voltage alarm: Two limits can be set with

the sliders. When the battery power falls

below or rises above these values, the user

will receive an app notification about the

state of charge.

4. Export data: Here you can email the history

data of the selected month in Excel or share

it via WhatsApp, Skype, Facebook, etc.

5. Unit: Here you can set the unit to metric or

imperial.

6. Firmware update: Here you can check the

hardware version and also update new

firmware when new version is available.

7. About: Here you can find privacy, FAQ, feed-

back and app version.

5.0 Further notes4.6 Settings

1. The product should not be used beyond the specified voltage range

(6-19 V), too high input voltage may damage the device.

2. The app requires smartphones with: Android 5.0 and above, iOS 10.0

or newer systems.

3. When the smartphone comes into Bluetooth range, it will receive a

notification.

4. If the daily test alert function is not enabled, when the smartphone is

in range, it also cannot receive the daily test result notification. You can

enable this both in the app and in the phone’s settings.

5. If the alert function is not enabled, when the smartphone is near the

device, it also cannot receive alert notification. You can enable the no-

tification both in the app and in the phone’s settings.

6. The firmware update will delete all data in the device. Please open the

app and wait for the sync to complete before updating the firmware.

7. All recorded data will be saved on the phone, when you upgrade the

app, this data will not be lost. But if the app is uninstalled, the data will

be deleted.

8. The device automatically monitors the vehicle battery, starting and

charging system. The device can store data up to 72 days. Please

connect the app at least once in 72 days to make sure the data is

saved for a long time.

9. If the app can not connect to the Battery Guard device, please make

sure the Bluetooth of the smartphone is on, you are near the device

and the device is added correctly.

FAQ: This submenu lists the frequently

asked questions and provides the corre-

sponding answers.

Feedback: Here you can give feedback

about the app or the device or report

problems.

App version: Display the current app version

number.

MODE D‘EMPLOI

EN FR IT ES

16-301-15 31-45 46-60

17 18

Le produit est utilisé pour surveiller la batterie de

la voiture, le système de démarrage et le système

de charge. Après avoir connecté l’appareil à la

batterie, il peut être relié à votre smartphone via

Bluetooth 5.3. Si des problèmes surviennent au

niveau de la batterie, du système de démarrage

ou du système de charge, il peut envoyer une

notification à l’utilisateur. En outre, l’utilisateur

peut également enregistrer les trajets qu’il a

effectués. Ce produit est compatible avec toutes

les batteries 12 V plomb-acide et lithium.

Table des matières

1.0 Informations sur le produit .............................................................. page 19

2.0 Consignes de sécurité ......................................................................... page 19

3.0 Instructions de montage ................................................................... page 19

4.0 Installation de l‘application ............................................................. page 20

4.1 Rayon d‘action du Bluetooth ........................................................... page 20

4.2 Utilisation de l‘application ............................................................... page 21

4.3 Test de démarrage ............................................................................... page 25

4.4 Test de charge ........................................................................................ page 26

4.5 Aperçu des trajets ................................................................................ page 28

4.6 Réglages ................................................................................................... page 29

5.0 Autres remarques ................................................................................. page 30

Indice

Lingue:

Altri manuali Intact Apparecchiature di prova

Intact

Intact BT701 Manuale utente

Intact

Intact BTJ41 Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente