Integra FLAMEBOY Manuale utente

145951_V01_QSG_FLAMEBOY_EN.docx 1/3

Quick Start Guide FLAMEBOY Handheld Bunsen Burner

This quick start guide is intended to provide a quick overview of your FLAMEBOY’s

key features and to offer basic instructions for getting started. For

detailed

information, please refer to the operating instructions (OI)

that can be found at

www.integra-biosciences.com in different languages.

Intended use

This is a general-purpose laboratory instrument. Any use of this instrument in a medical or IVD

setting is the sole responsibility of the user. FLAMEBOY is a portable, hand-held and automatic

laboratory flame burner used for surface sterilization. It provides piezo-electric ignition at the push of

a button.

Safety information

Regardless of the listed safety notes, all locally applicable regulations must be observed.

1) FLAMEBOY may only be used by properly trained personnel under constant supervision in a

manner specified by INTEGRA Biosciences.

2) Do not point the FLAMEBOY in the direction of persons or inflammable products. There is the

risk of burns from the flame and the still hot burner tube.

3) Do not use the FLAMEBOY near flammable material or in explosive areas. Work only in well

ventilated areas.

4) Use only approved and tested safety gas tubing with threaded or hose connectors.

5) Firmly tighten all gas connections and verify gas tightness, e. g. with soap water.

6) Be sure to close off the gas supply before: Transport of the device, changing the nozzle, the

adapter or the gas cartridge, longer breaks, cleaning work.

7) Servicing work and repairs may only be performed by INTEGRA Biosciences or an authorized

after-sales service member.

Overview FLAMEBOY

a. Air knob, to adjust the flame temperature

b. Brass screw, for replacing the nozzle

c. Gas knob, to adjust the flame size

d. Adapter latch

e. Threaded adapter for gas hose

f. Threaded connector for gas tubing

g. Handle

h. Trigger

i. Burner tube

2/3 145951_V01_QSG_FLAMEBOY_EN.docx

Fitting the nozzle for the gas in use

The P80 nozzle for butane/propane gas is fitted ex-factory. If necessary, replace the nozzle.

Type of gas

Nominal and maximal

gas input pressure

Inscription nozzle

Natural (>85 % methane) gas

20 mbar

N110

Butane/propane gas

50 mbar

P80

Town (methane, others) gas

8 mbar

M250

Turn the gas flow control valve to have access to the brass screw (b). Remove the screw, turn over

the device and allow the nozzle to drop out. Insert a new nozzle and retighten the brass screw.

FLAMEBOY may only be operated with the nozzle that corresponds to the gas type in use.

Inspect the O-ring in the brass screw for damage and, if necessary, replace it.

Connection of an adapter

When replacing the adapters, always close off the gas supply and remove the gas

cartridge.

•Insert the appropriate adapter in the opening down on the handle (g).

Make sure it audibly clicks into position.

•To remove the adapter, use a pointed tool to press the turquoise

adapter latch (d) inward and pull out the adapter downwards.

Connecting a gas cartridge

The P80 nozzle and the gas cartridge adapter must be installed. Gas cartridges may only

be used at 15 .C°53 – Only replace a gas cartridge, if the adapter is connected to the

device and closed.

CV360 cartridge adapter:

•Hold the brass knurled wheel of the gas cartridge adapter and close

the valve by unscrewing the black cap clockwise.

•Press the gas cartridge into the cap until its audibly clicks into

position.

•Hold the brass knurled wheel and open the valve by screwing the

black cap all the way in.

EXPRESS 444 cartridge adapter:

•Hold the brass knurled wheel and connect the gas cartridge by

screwing it clockwise into the adapter.

Connecting a tubing

•Screw the threaded connector of the gas tubing onto the adapter and

tighten it with a 17 mm fork wrench.

Or:

•Connect the end of the gas hose to the adapter and fix it with a

tubing clamp.

145951_V01_QSG_FLAMEBOY_EN.docx 3/3

Operation

Turn the gas knob (c) counterclockwise to the left. The FLAMEBOY is ignited by slowly pulling the

trigger (h). The flame burns as long as the trigger is pulled.

Rotating the gas knob (c) clockwise reduces the gas supply and counterclockwise increases it.

Moving the air knob (a) to the left reduces air supply, moving it to the right increases it.

Maintenance

Allow the burner tube to cool off before cleaning the device. Disconnected the device form

the gas supply. Allow the device to dry before operating it again.

•Clean the FLAMEBOY with a cloth moistened with soapy water or with a 70 % ethanol solution.

•The stainless steel burner tube (i) can be disinfected with commercially available disinfection

agents.

•If the FLAMEBOY has been contaminated, disinfect the housing with a lint-free cloth, lightly

soaked with a disinfectant and wipe dry directly after decontamination.

Equipment Disposal

FLAMEBOY must not be disposed of with unsorted municipal waste.

Dispose of FLAMEBOY in accordance with the regulations in your area governing disposal

of devices.

Manufacturer

INTEGRA Biosciences AG

CH-7205 Zizers, Switzerland

T +41 81 286 95 30

F +41 81 286 95 33

INTEGRA Biosciences Corp.

Hudson, NH 03051, USA

T +1 603 578 5800

F +1 603 577 5529

info@integra-biosciences.com

www.integra-biosciences.com

Altri manuali per FLAMEBOY

Indice

Altri manuali Integra Attrezzature da laboratorio

Integra

Integra VIAFLO 96 Manuale utente

Integra

Integra WELLJET 5000 Manuale utente

Integra

Integra MEDIAJET Manuale utente

Integra

Integra Evolve 3011 Manuale utente

Integra

Integra VIAFLO 96 Manuale utente

Integra

Integra ASSIST PLUS Manuale utente

Integra

Integra Luxtec 9300XSP Manuale operativo

Integra

Integra PIPETBOY acu 2 Manuale utente

Integra

Integra VIAFLO ASSIST 4500 Manuale utente

Integra

Integra VIAFLO 96 6000 Manuale utente

Integra

Integra PIPETBOY pro Manuale utente

Integra

Integra VIAFLO 4011 VIAFLO 4012 Manuale utente

Integra

Integra MEDIAJET Manuale utente

Integra

Integra MEDIACLAVE 10 Manuale utente

Integra

Integra MINI 96 Manuale utente

Integra

Integra PIPETBOY pro Manuale utente

Integra

Integra MEDIACLAVE 10 Istruzioni operative

Integra

Integra ASSIST PLUS Manuale utente

Integra

Integra VACUSAFE Manuale utente

Integra

Integra MINI 96 Manuale utente

Integra

Integra Cusa Excel Manuale utente

Integra

Integra CELLROLL Manuale utente

Integra

Integra WELLJET 5000 Manuale utente

Integra

Integra VACUSIP Manuale utente

Manuali Attrezzature da laboratorio popolari di altre marche

Qiagen

Qiagen DML 3000 Manuale utente

Queensgate

Queensgate NANOSCAN OP400 Manuale di programmazione

Conviron

Conviron GEN1000-GE Manuale utente

Parr Instrument

Parr Instrument 4560 Manuale di istruzioni

IKA

IKA IC control Manuale utente

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuale utente

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuale utente

NI PXI-5422 Manuale

Collomix

Collomix Aqix Manuale utente

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuale utente

Ocean Insight

Ocean Insight FLAME-NIR+ Manuale utente

Parker

Parker ALIGN-MG-NA Manuale utente

BD 644787 Manuale utente

DENTAURUM

DENTAURUM Compact Megaplus Manuale utente

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuale utente

VWR

VWR SAS Super IAQ Manuale utente

illumina

illumina MiSeqDx Manuale utente

Yamato

Yamato BM510 Manuale utente