Intel D845GERG2 - OCTOBRE 2002 Manuale utente

A99402-005

Intel®Desktop Boards

D845GERG2 and D845GEBV2

Quick Reference

This guide is written for technically qualified personnel with experience

installing and configuring desktop boards.

Before You Begin..................................................................................... 3

Warning and Cautions......................................................................... 3

Safety and Regulatory Notice ............................................................. 3

Desktop Board Components ................................................................ 4

Supported Components......................................................................... 5

Installation Steps ..................................................................................... 7

1 Installing the I/O Shield ................................................................ 7

2 Installing the Desktop Board......................................................... 7

3 Installing the Processor ................................................................. 8

4 Installing the Memory Modules .................................................... 8

5 Installing an AGP Card................................................................. 9

6 Attaching IDE Drives................................................................... 11

7 Connecting Fans........................................................................... 12

8 Connecting Power Cables ............................................................ 12

Using the BIOS Setup Program........................................................... 13

Setting the BIOS Configuration Jumper Block ............................... 13

Troubleshooting...................................................................................... 14

Customer Support Links....................................................................... 15

Items on the Intel®Express Installer CD-ROM

• Product warranty

• Intel Express Installer

• Intel®Desktop Boards D845GERG2 and D845GEBV2 Product Guide

• Software utilities and drivers

• Software license agreement

• Readme file

2 Intel Desktop Boards D845GERG2 and D845GEBV2

Quick Reference

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH

INTEL®PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL

OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED

BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL’S TERMS AND

CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO

LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR

IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL

PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO

FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR

INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL

PROPERTY RIGHT. INTEL PRODUCTS ARE NOT INTENDED FOR USE IN

MEDICAL, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS. INTEL MAY

MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT

ANY TIME, WITHOUT NOTICE.

Desktop Boards D845GERG2 and D845GEBV2 may contain design defects or

errors known as errata which may cause the product to deviate from published

specifications. Current characterized errata are available on request.

Contact your local Intel sales office or your distributor to obtain the latest

specifications and before placing your product order.

Copies of documents which have an ordering number and are referenced in this

document, or other Intel literature, may be obtained from Intel Corporation by

going to the World Wide Web site at: http://www.intel.com or by calling

1-800-548-4725.

Intel and Pentium are registered trademarks of Intel Corporation or its

subsidiaries in the United States and other countries.

†Other names and brands may be claimed as the property of others.

Intel Desktop Boards D845GERG2 and D845GEBV2 3

Quick Reference

Before You Begin

Warning and Cautions

WARNING

Disconnect the board’s power supply from its AC power source

before you connect or disconnect cables, or install or remove any

board components. Failure to do this can result in personal injury or

equipment damage. Some circuitry on the desktop board can

continue to operate even though the front panel power switch is off.

CAUTION

Electrostatic discharge (ESD) can damage desktop board components.

Install the board at an ESD-controlled workstation. If such a workstation

is not available, wear an antistatic wrist strap or touch the surface of the

antistatic package before handling the board.

CAUTION

Many of the midboard and front panel connectors provide operating

voltage (+5 V DC and +12 V DC, for example) to devices inside the

computer chassis, such as fans and internal peripherals. These

connectors are not overcurrent protected. Do not use these connectors

for powering devices external to the computer chassis. A fault in the load

presented by the external devices could cause damage to the computer,

the interconnecting cables, and the external devices themselves.

Safety and Regulatory Notice

See the Intel®Desktop Boards D845GERG2 and D845GEBV2 Product Guide

for all applicable regulatory compliance statements, product certification

markings, and safety and electromagnetic compatibility (EMC) standards and

regulations these desktop boards are compliant with.

Replacement battery warning label provided: Place the label inside the chassis

in an easy-to-see location near the battery but not on the board itself.

Intended uses: This product was evaluated as information technology

equipment (ITE) for home or office use when installed into an appropriate

computer chassis. Other end uses or locations may require further evaluation.

4 Intel Desktop Boards D845GERG2 and D845GEBV2

Quick Reference

Desktop Board Components

OM13885

USB 2.0

Devices

Line

2-pin alternate

power/sleep LED

connector

ABCDE

USB 2.0

Devices

Reset

HD LED Power LED

No Connection

Intel Desktop Boards D845GERG2 and D845GEBV2 5

Quick Reference

Desktop Board Components (continued)

A Audio codec N Primary IDE connector

B Front panel audio connector O Speaker

C Auxiliary line-in connector (ATAPI) P Battery

D Rear chassis fan connector

Q SCSI hard drive activity LED

connector

E CD-ROM connector (ATAPI) R Chassis intrusion connector

F 12 V processor core voltage

connector S Front chassis fan connector

G Intel®Graphics and Memory

Controller Hub (GMCH) T BIOS configuration jumper block

H Processor socket U Intel®I/O Controller Hub (ICH4)

I Processor fan connector V Front panel USB 2.0 connector

J DIMM sockets W AGP connector

K Main power connector X PCI bus add-in card connectors

L Diskette drive connector Y Communication and Networking

Riser (CNR) (optional)

M Secondary IDE connector

✏NOTE

The number of PCI slots on your board may differ from those in the

illustrations.

Supported Components

Processors

The board supports a single processor with the following features:

Type

Designation Front Side Bus

Frequency

L2 Cache

2.8, 2.66, 2.53,

2.4B, and

2.26 GHz

533 MHz 512 KB

Intel®Pentium®4 processor

on .13 micron process in an

mPGA478 package 2.6, 2.5, 2.40,

2.20, 2A, 1.80A,

and 1.60A GHz

400 MHz 512 KB

Intel Pentium 4 processor on

.18 micron process in an

mPGA478 package

2, 1.90, 1.80,

1.70, 1.60, 1.50,

and 1.4 GHz

400 MHz 256 KB

Intel®Celeron®processor in

an mPGA478 package 1.8 and 1.7 GHz 400 MHz 128 KB

For the latest information on processors supported by Desktop Boards

D845GERG2 and D845GEBV2, refer to the Intel World Wide Web site at:

http://support.intel.com/support/motherboards/desktop

6 Intel Desktop Boards D845GERG2 and D845GEBV2

Quick Reference

Memory Module Requirements

The desktop board supports system memory as defined below:

• Up to two 184-pin Double Data Rate (DDR) SDRAM Dual Inline Memory

Modules (DIMMs) with gold-plated contacts. Supported memory

configuration are:

— DDR333: to run DDR333 memory at full speed requires an Intel

Pentium 4 processor with 533 MHz front side bus frequency (FSB).

DDR333 memory will run only at DDR266 speeds when using a

processor with 400 MHz FSB.

— DDR266: requires an Intel Pentium 4 processor with 533/400 MHz

FSB, or Intel Celeron processor with 400 MHz FSB.

• Unbuffered and non-registered single or double-sided DIMMs

• Serial Presence Detect (SPD) memory only

• Non-ECC RAM (ECC memory will run in non-ECC mode)

• 2.5 V memory

✏NOTES

Desktop Boards D845GERG2 and D845GEBV2 have been designed to

support DIMMs based on 512 Mbit technology up to 2 GB, but this

technology has not been validated on these boards.

All memory components and DIMMs used with the desktop boards must

comply with the PC SDRAM specifications. These include the PC

SDRAM Specification (memory component specific), the PC Unbuffered

DIMM Specification. To view or download these specifications, refer to

this Intel World Wide Web site:

http://www.intel.com/technology/memory/pcsdram/

For information about vendors that support these memory requirements,

refer to the Desktop Boards D845GERG2 and D845GEBV2 link on this

Intel World Wide Web site:

http://support.intel.com/support/motherboards/desktop/

Intel Desktop Boards D845GERG2 and D845GEBV2 7

Quick Reference

Installation Steps

1 Installing the I/O Shield

The board comes with an I/O shield. When installed in the chassis, the shield

blocks radio frequency transmissions, necessary to pass emissions (EMI)

certification testing, protects internal components from dust and foreign objects,

and promotes correct airflow within the chassis.

Install the I/O shield before installing the board in the chassis. Place the shield

inside the chassis as shown in the following figure. Press the shield into place so

that it fits tightly and securely. If the shield doesn’t fit, obtain a properly sized

shield from the chassis supplier.

OM12116

2 Installing the Desktop Board

Refer to your chassis manual for specific instructions on installing and removing

the desktop board.

Desktop Board D845GERG2 is secured to the chassis with six and Desktop

Board D845GEBV2 with eight screws. Refer to the board illustration on page 4

for the location of the mounting holes.

8 Intel Desktop Boards D845GERG2 and D845GEBV2

Quick Reference

3 Installing the Processor

To install the processor, follow these steps:

1. Observe the precautions in “Before You Begin” on page 3.

2. Lift the processor socket lever.

3. Install the processor so that the corner with the triangle marking (A) is

aligned with the corner where the lever is attached to the socket.

4. Lower the lever back to its original position.

OM12078

mPGA478B

5. The desktop board has an integrated processor fan heat sink retention

mechanism (RM). For instructions on how to install the processor fan heat

sink, refer to the boxed processor manual or the Intel World Wide Web

site at:

http://support.intel.com/support/processors/pentium4/intnotes478.htm

4 Installing the Memory Modules

CAUTION

Install memory in the DIMM sockets prior to installing the AGP video card

to avoid interference with the memory retention mechanism.

The two DIMM sockets are arranged as DIMM 0 and DIMM 1, as shown in the

following figure. If installing a single DIMM, install it in DIMM 0.

To install DIMMs, follow these steps:

1. Remove the AGP video card if it interferes with the DIMM clips from

being easily opened and closed.

2. Align the small notch in the bottom edge of the DIMM with the key in the

socket.

Intel Desktop Boards D845GERG2 and D845GEBV2 9

Quick Reference

3. Insert the bottom edge of the DIMM into the socket.

4. When the DIMM is inserted, push down on the top edge of the DIMM until

the retaining slips snap into place. Make sure the clips are firmly in place.

OM14774

DIMM 0

DIMM 1

5 Installing an AGP Card

CAUTION

Care must be taken when installing an AGP or ADD card into an

AGP slot.

When installing any AGP or ADD card in the desktop board, ensure that it

is fully seated in the AGP connector before you power on the system. If

the card is not fully seated in the AGP connector, an electrical short may

result across the AGP slot pins. Depending on the over-current protection

of the power supply, certain board components and/or traces may be

damaged.

✏ NOTE

Desktop Boards D845GERG2 and D845GEBV2 are only compatible with

1.5 V AGP cards.

10 Intel Desktop Boards D845GERG2 and D845GEBV2

Quick Reference

Desktop Boards D845GERG2 and D845GEBV2 have an integrated AGP card

retention mechanism (RM).

Follow these instructions to install an AGP card:

1. Place the AGP card in the AGP connector.

2. Press down on the card until it is completely seated in the connector and the

card retention notch snaps into place below the RM.

3. Secure the card’s metal bracket to the chassis back panel with a screw.

Install PCI cards into the PCI bus add-in card connectors on the desktop board.

OM14695

To remove the AGP card, reverse steps taken when installing an AGP card.

Before removing the card, make sure to push back on the RM lever (A) until the

retention pin completely clears the notch in the card.

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Intel Scheda madre

Intel

Intel DP55WG - Media Series P55 ATX Core i7 i5 LGA1156 Desktop... Manuale tecnico

Intel

Intel D945PAW Manuale utente

Intel

Intel BLKDG35EC Guida alla configurazione

Intel

Intel DZ87KLT-75K Manuale utente

Intel

Intel BOXD945PVSLKR Guida alla configurazione

Intel

Intel S5520HCR Manuale utente

Intel

Intel BOXD910GLDW - Desktop Board D910GLDW Manuale utente

Intel

Intel DP67BG Manuale utente

Intel

Intel 1037U Manuale utente

Intel

Intel DP55KG - Desktop Board Extreme Series... Guida rapida

Intel

Intel DH57DD Manuale utente

Intel

Intel DH61WW Guida alla configurazione

Intel

Intel i915G Manuale utente

Intel

Intel DQ67OW Manuale utente

Intel

Intel S3000PT Manuale utente

Intel

Intel Celeron 1047UE/847 Manuale utente

Intel

Intel BLKD945GCLF2 Manuale utente

Intel

Intel DH77EB Manuale utente

Intel

Intel BLKDQ35JO Manuale utente

Intel

Intel D845GRG Manuale utente

Intel

Intel D865PCK Manuale utente

Intel

Intel Desktop Board D845GVFN Manuale utente

Intel

Intel i945P Manuale utente

Intel

Intel D915GVWB Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuale utente