Interlogix TruPortal TP-ADD-2D-BRD Manuale utente

P/N 460802001C • REV 01.00 • 25JUL13 1

TruPortal™Dual Door

Interface Module

Quick Reference

en-US

Introduction

The TruPortal Dual Door Interface Module (TP-ADD-2D) can

support two complete door configurations, with up to two readers

per door. This module provides termination points for door

contacts (door position switches) and Request to Exit (RTE)

devices, as well as two door strike relays to control power to the

controlled access doors. It communicates with the TruPortal

System Controller (TP-SYS) via a two-wire RS-485 SNAPP bus.

Model Numbers

The TruPortal Dual Door Interface Module is available in a board-

only configuration (TP-ADD-2D-BRD) (see Figure 9) or pre-

installed in a UL or CE enclosure with or without bundled readers

and credentials (TP-ADD-2DR, TP-ADD-2D).

The TruPortal Dual Door Interface Module is available in the

following configurations:

• TP-ADD-2D-BRD (board only)

• TP-ADD-2D (installed in UL enclosure)

• TP-ADD-2D2R (installed in UL enclosure with two readers)

• TP-ADD-2D-E (installed in CE enclosure)

• TP-ADD-4D (installed in UL enclosure with two Dual Door

Interface Modules)

Note: -E model numbers are “Not Evaluated by UL” and

therefore cannot be used in UL installations.

Packing List

• TruPortal Dual Door Interface Module (quantity = 1)

• Mounting plate (depending on option ordered)

• UL or CE enclosure with power supply (depending on option

ordered)

• T-100 readers (depending on option ordered; quantity = 2)

• Installation kit which includes:

- Two positional terminal plug-in block (quantity = 5)

- Three positional terminal plug-in block (quantity = 4)

- Four positional terminal plug-in block (quantity = 4)

- Six positional terminal plug-in block (quantity = 2)

- 1N4005 diodes (quantity = 2)

- End-of-Line (EOL) resistors 1k ohm, 1% (quantity = 8)

- Plastic board supports for optional mounting

(quantity = 4)

Installation Procedure

To install the TruPortal Dual Door Interface Module, perform the

procedures described in the following sections, in the order in

which they are presented.

1. Mount the enclosure.

2. Mount the module in the enclosure.

3. Wire the relay outputs for door strike(s) and AUX.

4. Wire the reader(s).

5. Install the reader voltage jumpers.

6. Wire the alarm inputs.

7. Wire the tamper switch.

8. Wire the power and communications inputs

9. Apply power to the unit and listen for the relays to click.

Observe LED indicators to verify correct board operation.

10. Ensure all wires are clear and secure the cover.

WARNING: Circuit board components are vulnerable to damage

by electrostatic discharge (ESD). ESD can cause

immediate or subtle damage to sensitive electronic

parts. An electrostatic charge can build up on the

human body and then discharge when touching a

board. A discharge can be produced when walking

across a carpet and touching a board, for example.

Before handling any board, make sure to dissipate

any charge by touching the ground. This discharges

any static electricity build-up.

2TruPortal Dual Door Interface Module Quick Reference

Mounting the Enclosure

1. Remove enclosure from shipping container and remove any

packing material.

2. Using the template provided (part number 531119001 or

531120001), mark and then drill mounting holes.

3. To mount on dry wall, use 1/8 in. (3.175 mm) hollow wall,

expansion anchors. Unscrew the screws from the anchors.

Mark the mounting holes. Force a starter hole in each mark

with a sharp tool. Hammer the anchors into each hole. Align

the box mounting holes over the anchor holes and screw in

the anchors until tight.

To mount on a concrete surface, hold the enclosure on the

mounting surface. Mark the mounting holes. Use a hammer

drill with a 3/16 in. (4.76 mm) carb alloy drill bit and make

1 in. (25.4 mm) deep holes in each marking. Insert a # 6-8

plastic anchor in each hole and hammer them in. Use # 8 X

1 in.(25.4 mm), Phillips wood screws to screw into the plastic

anchors and mount the enclosure.

4. The enclosure includes standard cable knockouts on each

side, including the back. Use the proper size and type of

cable strain reliefs to secure cables to the enclosure.

See Figure 10 for TP-ADD-2D enclosure dimensions. For

TP-ADD-4D dimensions, see Figure 11.

Mounting the Module in the Enclosure

Use the provided hardware as required to mount the module in

the enclosure.

Note: Do not over-tighten the mounting screws.

• To mount the module in the AL400 enclosure using the

mounting plate, see Figure 12.

• To mount the module in the AL600 enclosure using the

mounting plate, see Figure 13.

• To mount the module in AL400 enclosure without the

mounting plate, see Figure 14.

• To mount the module in AL600 enclosure without the

mounting plate, see Figure 15.

Wiring

(See Figure 1.)

For the Door Unlock Circuit, a diode is provided to protect against

voltages induced when a DC strike is de-energized. For an AC

strike, or a magnetic-lock with reversing coils (or if unsure), a 27 V

Metal Oxide Varistor (MOV) must be used.

Verify that at least 10.5 VDC is at each device (with relays

energized). Use additional power supplies as necessary.

For large current-draw devices with built-in power supplies,

connect the incoming and outgoing module bus +12 VDC lines

together, but do not connect to the +12 VDC in the enclosure.

Terminal Block (TB) 6 can be used to daisy chain the SNAPP bus.

Bring the bus wiring through TB1 and continue the wiring out

through TB6.

Figure 1: Components and Cable Specifications

The following table lists the items shown in Figure 1.

Callout Description Callout Description

1Reader cable (22 AWG,

(0.64 mm / 0.33 mm2)

shielded, 3 pairs)

10 Door 1 or 2 (with door

closer)

2Door contact/sensor

wiring (22 AWG, 1 pair)

11 Last module

3Request to Exit (RTE) 12 Transformer

4RTE button wiring

(22 AWG (1.02 mm/

.82 mm2), 1 pair)

13 Power supply

5Door lock 14 Next module

6Door lock wiring

(18 AWG, 1 pair)

15 Module bus (24 AWG

(.51 mm/.20 mm2),

four shielded wires,

120 ohms)

7AUX relay wiring

(22 AWG, 1 pair)

16 To System Controller

(TP-SYS) or previous

module

8AUX input wiring

(22 AWG, 1 pair)

17 12 VDC input power

9AUX input 18 Dual Door Interface

Module (TP-ADD)

12 11

TruPortal Dual Door Interface Module Quick Reference 3

Output Wiring

The contact protection circuit must be used. The two circuits

shown in Figure 2 and Figure 3 are recommended. Locate the

protection circuit as close to the load as possible (within 12 in.

[30 cm]), as the effectiveness of the circuit will decrease if it is

located further away.

Figure 2: Recommended Circuit #1

Figure 3: Recommended Circuit #2

Magnetic Locks and Other “Fail-Safe” Door Locks

The default door lock wiring is for “Fail Secure” (powered =

unlocked). For magnetic locks and other “Fail-Safe” door locks

(powered = locked), move the Normally Open (NO) wire to

Normally Closed (NC) terminal for the specific unlock relay.

Note: The System shall not be installed in the Fail Secure

mode unless permitted by the local authority having

jurisdiction and shall not interfere with the operation of

panic hardware. (Not evaluated by UL.)

Figure 4: Door Lock Wiring

Reader Wiring

Figure 5: Reader Wiring

The following table lists the items shown in Figure 5

For the second reader of each door, the reader connections are

shared (except for the Data 0 and Data 1, which are separate for

each reader).

Callout Description Callout Description

1 12 VDC 3 Diode current rating >1x strike

current. Diode breakdown voltage

>4x strike voltage for 12 or

24 VDC strike. Diode 1N4002

(100 V/1 A) typical.

2 DC strike 4 TB5 or TB8 on module.

Callout Description Callout Description

1 AC transformer 3 Clamp voltage >1.5x VAC RMS.

For 24 VAC strike, Panasonic

ERZ-CO7DK470 is typical.

2 AC strike 4 TB5 or TB8 on module.

Callout Description Callout Description

1 Reader (TB2 or TB11

on module)

9R2Data0

2 (+) 5/12 VDC 10 Red (1)

3 Green LED 11 Brown (4)

4 Red LED 12 Orange (5)

5 R1 Data 1 13 White (3)

6R1Data0 14Green(2)

7 (-) 0V Signal Ground 15 Black (6)

8R2Data1

1 NC

2 Com

3 NO

123456 12

TB11

5/12 GRN

RED/

RXD GNDR1D1 R1D0 R2D1 R2D0

6 8

4TruPortal Dual Door Interface Module Quick Reference

Reader Voltage Jumpers

For reader power (data line pull-up) voltage selection, refer to the

following table and Figure 6:

Reader Status LEDs

To interpret reader status LEDs, refer to the following table and

Figure 6:

Figure 6: Reader Jumpers and LEDs

Alarm Input Door Contact Detail and Request to Exit

Note the following details about the Figure 7:

• Door contacts (NC & NO) are for reference only, and must

match the door state.

• Callout #1 represents the enclosure tamper switch.

Figure 7: Tamper Wiring

Communications (SNAPP Bus) and Power Wiring

Communication ports TB1 and TB6 are two-wire RS-485

interfaces used to connect RS-485 from the System Controller

(TP-SYS) to additional input/output (I/O) modules downstream.

The interface allows multidrop communication on a single bus of

up to 4000 feet (1200 m). Use twisted pairs (minimum 22 AWG /

0.644 mm / 0.326 mm) with an overall shield for communication.

Figure 8: Communications Power Wiring

Note: Door Interface Modules (TP-ADD boards) cannot be

powered from the System Controller (TP-SYS).

Callout Description

1 Use J1 pins 1 and 2 for +12 VDC Data Lines.

Use J1 pins 2 and 3 for +5 VDC Data Lines

2 Use J2 pins 1 and 2 for +12 VDC Data Lines;

Use J1 pins 2 and 3 for +5 VDC Data Lines

Callout Indication LED State

3 485-SNAPP bus OK DS1 ON Green

4 Processor OK DS2 Flashing Green

5 Low power DS7 ON Red

Callout Description

1 +12 V from TP-ADD power supply, pre-wired at the factory

2 Data A from System Controller (TP-SYS)

3 Data B from System Controller (TP-SYS)

4 0 V from TP-ADD power supply

5 TP-ADD-2D-BRD

6 TP-ADD-2D-BRD (downstream)

7 +12 V and 0 V external power source, pre-wired at the factory

8 To additional TP-ADD-2D or TP-ADD-IN/OUT boards

9 Common ground from System Controller (TP-SYS)

10 Terminate cable shield to ground lug in System Controller

TruPortal Dual Door Interface Module Quick Reference 5

Table 1: Dual Door Interface Module Pinouts

Callout Description Callout Description

1TB1 (Module Bus;

wired from previous

device and to next

device)

9TB9 (Input)

2TB2 (Reader) 10 TB10 (Input)

3TB3 (Input) 11 TB11 (Reader)

4TB4 (Input) 12 Door 2 (one or two

readers)

5TB5 (Unlock Relay

and Aux Relay, with

pins NC2, NO2, and

COM2 for Unlock

Relay)

13 Door 2 reader

voltage

6TB6 (Module Bus) 14 Door 1 (one or two

readers)

7Tam p e r 15 Door 2 reader

voltage

8TB8 (Unlock Relay

and Aux Relay, with

pins NC2, NO2, and

COM2 for Unlock

Relay)

Terminal Block Pin Label Description

TB1 +12V (+) 12 V - Red

A Data A - Green

B Data B - Yellow

0V (-) 0V - Black

TB2 5/12 (+) 5/12 VDC

GRN Green LED

RED/RXD Red LED

R1D1 R1 Data 1

R1D0 R1 Data 0

GND (-) 0 V Signal Ground

R2D1 R2 Data 1

R2D0 R2 Data 0

TB3 DCNT Door Contact Input

GND COM/Shared

RTMP Reader Tamper

BUZ BUZ Out (-)

Figure 9: Dual Door Interface Module

1 21231231 2 3 4

GND RTMP BUZ 5/12 GRN RED/

RXD GNDDCNTRTEGNDAUXNO2COM2 R1D1 R1D0 R2D1NC2COM1NO1 R2D0

0VBA

+5V

+12V

12 34 5 612

1234

+12V5/12 GRN RED/

RXD

GNDR1D1 R1D0 R2D1 R2D0

12 34 56121234

GND RTMP BUZ

DCNT

123

RTE

GND

AUX

12123

NO2COM2NC2COM1NO1

0VBA

1234

+12V

41 32

6TruPortal Dual Door Interface Module Quick Reference

TB4 AUX Aux Input

GND COM/Shared

RTE Request to Exit

TB5 NO1 Normally Open

COM1 Aux Relay

NC2 Normally Closed

COM2 Common

NO2 Normally Open

TB6 +12V (+) 12V - Red

A Data A - Green

B Data B - Yellow

0V (-) 0V - Black

TB8 NO1 Normally Open

COM1 Aux Relay

NC2 Normally Closed

COM2 Common

NO2 Normally Open

TB9 AUX Aux Input

GND COM/Shared

RTE Request to Exit

TB10 DCNT Door Contact Input

GND COM/Shared

RTMP Reader Tamper

BUZ BUZ Out (-)

TB11 5/12 (+) 5/12 VDC

GRN Green LED

RED/RXD Red LED

R1D1 R1 Data 1

R1D0 R1 Data 0

GND (-) 0V Signal Ground

R2D1 R2 Data 1

R2D0 R2 Data 0

Terminal Block Pin Label Description

TruPortal Dual Door Interface Module Quick Reference 7

Figure 10: TP-ADD-2D Enclosure Dimensions Figure 11: TP-ADD-4D Enclosure Dimensions

Callout Description

1Front view; cover not shown

2Bottom view; top view the same

3Side view typical

40.20 in. (05 mm) and .38 in. (9.6 mm) double

keyhole in 3 holes.

5Combination 1.124 in. (28.6 mm) and .875 in.

(22.2 mm) knockout typical

Callout Description

1Front view; cover not shown

2Bottom view; top view the same

3Side view typical

40.20 in. (05 mm) and 38 in. (9.6 mm) double

keyhole in 6 holes.

5Combination 1.125 in. (29 mm) and 1,375 in.

(35 mm) knockout typical

8TruPortal Dual Door Interface Module Quick Reference

Figure 12: Mounting in AL400 Enclosure with Mounting Plate Figure 13: Mounting in AL600 Enclosure with Mounting Plate

Callout Description

1TP-ADD-2D

228058B-02 mounting plate

3TP-ADD (AL400) enclosure

4#6-32 SEMS nut, 8 holes

5#6-32 x .38 in. (9.652 mm), 4 holes

Callout Description

1TP-ADD-2D

228058B-02 mounting plate

3TP-ADD (AL600) enclosure

4#6-32 SEMS nut, 8 holes

5#6-32 x .38 in. (9.652 mm), 4 holes

TruPortal Dual Door Interface Module Quick Reference 9

Figure 14: Mounting in AL400 Enclosure without Mounting Plate Figure 15: Mounting in AL600 Enclosure without Mounting Plate

Callout Description

1TP-ADD-2D

2TP-ADD (AL400) enclosure

3#6-32 x 1.00 in. (25.4 mm) plastic standoff, 4 holes

4#6-32 x .312 in. (7.925 mm), 4 holes

Callout Description

1TP-ADD-2D

2TP-ADD (AL600) enclosure

3#6-32 x 1.00 in. (25.4 mm) plastic standoff, 4 holes

4#6-32 x .312 in. (7.925 mm), 4 holes

10 TruPortal Dual Door Interface Module Quick Reference

Specifications

The TruPortal Dual Door Interface Module is for use in low

voltage, Class 2 circuits only. These specifications are subject to

change without notice.

Specifications

Regulatory Information

Contact Information

www.interlogix.com

Customer support: www.interlogix.com/support

Interlogix is part of UTC Climate Controls & Security, a unit of

Document number: 460802001C - July 2013

Dimensions 5.75 x 4.25 x 1 in. (146 x 108 x 25 mm)

Operating

environment

Temperature: +32 to +120° F (0 to +49° C )

Humidity: 5 to 85% RHNC at 77° F (25° C)

BTU Output: 12.3 BTU/hour

Incoming power

ratings

12 VDC, 300 mA max

Outputs Four outputs: Relay type

Door strike: 24 VDC/1 A

Aux: 24 VDC/0.1 A

Inputs Eight unsupervised/supervised, standard EOL, 1k/1k

ohm, 1% 1/4 watt

One unsupervised, dedicated for enclosure tamper

Reader interface Four interfaces

Reader power (jumper selectable): 12 VDC + 10%

regulated, 125 mA maximum each reader or 5 VDC +

10% regulated, 600 mA maximum each reader

Communication SNAPP bus (RS-485)

Cable requirements Power: 18 AWG (1.024 mm / 0.823 mm2), one

stranded

Reader data: six conductors, 18 AWG (1.024 mm /

0.823 mm2), 500 feet (150 m) maximum

SNAPP bus (RS-485): 22 AWG (0.644 mm / 0.326

mm2), 100 ohm impedance, twisted pair with shield,

4000 feet (1219 m) maximum

Manufacturer Interlogix

Headquarters and Regulatory responsibility:

Interlogix

3211 Progress Dr.

Lincolnton, NC 28092 USA

EU authorized manufacturing representative:

UTC Climate, Controls & Security B.V.,

Kelvinstraat 7, 6003 DH Weert,

The Netherlands

Year of

manufacture

The first two digits of the product serial number (located

on the product identification label) are the year of

manufacture.

North American

standards

UL 294

FCC

compliance

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2)

this device must accept any interference received,

including interference that may cause undesired

operation.

Certifications RoHS compliant, WEEE

European Union

directives

We declare under our sole responsibility that this product

is in conformity with Directive 1999/5/EC (R&TTE), 2004/

108/EC (EMC), 2006/95/EC (LVD), and 93/68/EEC

(Marking) based on test results using harmonized

standards in accordance with the Directives mentioned.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Interlogix Unità di controllo

Interlogix

Interlogix SuperBus 2000 PIV Manuale utente

Interlogix

Interlogix NX-586E Manuale utente

Interlogix

Interlogix SuperBus 2000 Manuale utente

Interlogix

Interlogix ATS7200N Istruzioni per il montaggio

Interlogix

Interlogix ATS7340 Istruzioni per il montaggio

Interlogix

Interlogix ATS1201 8 Istruzioni per il montaggio

Interlogix

Interlogix VR1101M Istruzioni per l'installazione

Interlogix

Interlogix ATS7200E Istruzioni per il montaggio

Interlogix

Interlogix NX-586E Manuale utente

Interlogix

Interlogix UM-ZW Manuale utente

Interlogix

Interlogix Simon XT Manuale utente

Interlogix

Interlogix NX-595E Manuale utente

Interlogix

Interlogix DIGITAL INVERTER GENERATOR Istruzioni per il montaggio

Interlogix

Interlogix ATS 500A Series Manuale utente

Interlogix

Interlogix DTIM Istruzioni per il montaggio

Interlogix

Interlogix 60-677 Manuale utente

Interlogix

Interlogix UltraSync UM-Z8 Istruzioni per il montaggio

Interlogix

Interlogix TX-E121 Manuale utente

Interlogix

Interlogix UltraSync UM-W7 Istruzioni per il montaggio

Interlogix

Interlogix 600-1046-95 Manuale utente

Interlogix

Interlogix NXG-7002 Istruzioni per il montaggio

Interlogix

Interlogix RF-KF101-K4 Istruzioni per il montaggio

Interlogix

Interlogix ITI SuperBus 2000 Manuale utente

Interlogix

Interlogix TruPortal TP-ADD-2D Series Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente