Interlogix TruVision TVB-2402 Foglio di istruzioni

TruVision High Definition

TVI Camera Configuration

Manual

TVB

-2402/TVB-4402

TVD

-2402/TVD-4402

P/N 1072941-EN • REV A • ISS 10MAR15

2015 United Technologies Corporation,

Interlogix is part of UTC Building & Industrial

Systems, a unit of

Trademarks and

patents

rade names used in this document may be trademarks or

registered trademarks of the manufacturers or vendors of the

respective products

Manufacturer

nterlogix

2955 Red Hill Avenue, Costa Mesa, CA 92626

-5923, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, The Netherlands

Contact information

For contact information

, see www.interlogix.com or

www.utcfssecurityproducts.eu

Customer suppor

www.interlogix.com/customer

-support

TruVision High Definition TVI Camera Configuration Manual 1

Content

Introduction 2

Programming 2

Menu 4

Automatic Exposure (AE) 4

White Balance (WB) 5

Day & Night 5

Video Setting 6

Function 6

Reset 8

2 TruVision High Definition TVI Camera Configuration Manual

Introduction

This is the configuration manual for following camera models:

TVB-2402 (720P TVI Bullet Camera, VF Lens, IR, PAL)

TVB-4402 (720P TVI Bullet Camera, VF Lens, IR, NTSC)

TVD-2402 (720P TVI Mini Dome, VF Lens, IR, PAL)

TVD-4402 (720P TVI Mini Dome, VF Lens, IR, NTSC)

Programming

Once the camera hardware has been installed, the camera can then be

configured using the built-in OSD button or an OSD controller (purchased

separately).

You can also configure the camera settings via a TVI DVR, select PTZ protocol

as TruVision Coax and click the menu button to call the menu.

Note:

Interlogix offers two different versions of the OSD Controller: the TVS-C100

controller and the TVS-C200 controller. Please choose the corresponding

controller by referring to product datasheets.

The cameras listed in the “Introduction” section support TruVision Coax OSD

control protocol and require the TVS-C200 for OSD control.

The TVS-C200 is used to program the camera’s 960H CVBS output, not for the

TVI video output. Programming the camera’s TVI output can be done via a TVI

DVR.

The TVS-C200 has four buttons for the camera functions selection and control.

Table 1 below lists the OSD control button functions and describes their use.

TruVision High Definition TVI Camera Configuration Manual 3

Figure 1: TVS-C200 coax controller

1. Indicator light

2. Arrow keys

3. OK button

The Setup menu provides access to the camera configuration options.

Before using the controller, please check to ensure that the controller has power.

Two AAA batteries are required for the controller to work properly.

1. Connect a video monitor to one of the BNC connectors of the controller.

2. Connect the camera’s 960H CVBS output to the other BNC connector

3. Press the OK button for few seconds to display the Setup menu. See Table 1

for instructions on how to move the cursor.

Table 1 Using the OSD control button

Button

direction Description

Moves the cursor upward to select an item

Left

Moves the cursor left to select or adjust the parameters of the selected

item.

Right

Moves the cursor to the right to select or adjust the parameters of the

selected item.

Down

Moves the cursor downward to select an item.

Press the red button for few seconds to display the Setup menu. If the

selected item has its own menu, press the button to enter a submenu.

4 TruVision High Definition TVI Camera Configuration Manual

Automatic Exposure (AE)

Automatic exposure (AE) allows you to automatically set the proper exposure

according to the existing light conditions.

Move the cursor to MAIN MENU > AE, to adjust the image brightness using the

BRIGHTNESS, AE MODE, AGC, and SENS-UP options.

BRIGHTNESS: Brightness refers to the brightness of the image. You can set the

brightness value from 1 to 10 to darken or brighten the image. The higher the

value, the brighter the image.

AE MODE: You can set AE mode as GLOBLE AE, and D-WDR:



GLOBAL AE: This refers to the normal exposure mode which is for adjusting

the situations including unusual lighting distribution, variations, non-standard

processing, or other conditions of under exposure to get an optimum image.



DWDR: The digital wide dynamic range (D-WDR) function helps the camera

provide clear images even under back light circumstances. When there are

TruVision High Definition TVI Camera Configuration Manual 5

both very bright and very dark areas simultaneously in the field of view, D-

WDR balances the brightness level of the whole image and provide clear

images with details.

AGC: This is a form of amplification where the camera will automatically boost

the image received in much lower light conditions than standard in order to

optimize the clarity of image in poor light scene. The AGC level can be set to

HIGH, MIDDLE, and LOW. Select OFF to disable the AGC.

Note: The noise will be amplified if the AGC is on.

SENSE UP: This increases the exposure on a signal frame, which makes a

camera more sensitive to light so it can produce images even in low lux

conditions. You can set the SENSE UP value from 0 to 16 according to the

different light conditions. The higher value is, the more frames integrated in a unit

of time.

White Balance (WB)

White balance is the white rendition function of the camera to adjust the color

temperature according to the environment. It can remove the unrealistic color

casts in the image. You can set the WB mode as AUTO or MANUAL.

AUTO: The white balance is adjusted automatically according to the color

temperature of the scene illumination.

MANUAL: You can set the R GAIN/B GAIN value from 1 to 10 to adjust the

shades of red/blue color of the image.

Day & Night

Move the cursor to MAIN MENU > DAY & NIGHT, and select COLOR, B/W, or

SMART as the DAY & NIGHT mode.

COLOR: The image is colored in day mode all the time.

B/W: The image is black and white all the time, and the IR LED turns on in low-

light conditions.

SMART: Turn on/off the INFRARED_LAMP and set the Smart IR level from 1to

16.

6 TruVision High Definition TVI Camera Configuration Manual

Video Setting

Move the cursor to the MAIN MENU >VIDEO SETTING.

CONTRAST: This feature enhances the difference in color and light between

parts of an image. Set the CONTRAST value from 1 to 10.

SHARPNESS: Sharpness determines the amount of detail an imaging system

can reproduce. You can also adjust the EDGE/DETAIL sharpness value. Set the

edge and detail sharpness value from 1 to 10. A higher value of sharpness

results in a clearer and sharper image.

COLOR GAIN: Adjust this feature to change the saturation of the color. Set the

color gain from 1 to 10.

3D NR: Compared to traditional general 2D NR technology, 3D NR processes

the noise reduction between two frames instead of in one frame. It can decrease

the noise effect, especially when capturing moving images in low light conditions

and delivering more accurate and sharp image quality. Set the 3D NR level as

High, Middle, and Low. Select OFF to disable the 3D NR.

MIRROR: Set the mirror mode as OFF, H, V, or HV.



OFF: The mirror function is disabled.



H: The image flips 180 degree horizontally.



V: The image flips 180 degree vertically.



HV: The image flips 180 degrees both horizontally and vertically.

Function

Move the cursor to the MAIN MENU > FUNCTION. You can set DETECTION,

MASKING, ZOOM IN and LANGUAGE of the camera in this menu.

TruVision High Definition TVI Camera Configuration Manual 7

DETECTION: In the user-defined detection surveillance area, the moving object

can be detected and the alarm will be triggered. Set the motion sensitivity as

WEAK, LOW, MIDDLE or HIGH. Select an AREA to enter the motion detection

AREA menu.

MASKING: Masking allows you to cover certain areas that you do not want to be

viewed or recorded. Up to eight masking areas are configurable. Select a

masking back ground color. Select an AREA to enter the masking AREA menu.

ZOOM IN: The ZOOM IN value can be adjusted from 50 to 100.

LANGUAGE: Select either Chinese or English.

AREA: There are four surveillance areas set for motion detection. Select one and

set the status as OFF/ON. Select a color for area border. Move the joystick

up/down and right/left to set the horizon/vertical size and position.

8 TruVision High Definition TVI Camera Configuration Manual

AREA: There can be eight masking areas set for motion detection. Set the status

as OFF/ON. Move the joystick up/down and right/left to set the horizon/vertical

size and position.

Reset

Move the cursor to the MAIN MENU >RESET. This resets all the settings to

default.

SAVE & EXIT: Move the cursor to SAVE & RESET and press OK to save the

settings and exit the menu.

Altri manuali per TruVision TVB-2402

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Interlogix Telecamera di sicurezza

Interlogix

Interlogix UVP-M1120P-18X-N Manuale utente

Interlogix

Interlogix TVP-6102 Manuale utente

Interlogix

Interlogix TVD-6120VE-2-N Manuale utente

Interlogix

Interlogix TruVision TVW-2401 Foglio di istruzioni

Interlogix

Interlogix TruVision TVB 2102 Manuale utente

Interlogix

Interlogix TruVision Line Foglio di istruzioni

Interlogix

Interlogix TruVision TVP-5201 Foglio di istruzioni

Interlogix

Interlogix UltraView UVC-6130-1-N Manuale utente

Interlogix

Interlogix TruVision Line Manuale utente

Interlogix

Interlogix TruVision TVC-7120-1-N Manuale utente

Interlogix

Interlogix TruVision TVB-2402 Istruzioni operative e di manutenzione

Interlogix

Interlogix TruVision TVD-N210V-2-N(-P) Manuale utente

Interlogix

Interlogix TruVision TVB-6102 Manuale utente

Interlogix

Interlogix TruVision 4 Series Manuale utente

Interlogix

Interlogix TruVision Line Manuale utente

Interlogix

Interlogix TruVision HD-TVI 3MPX Foglio di istruzioni

Interlogix

Interlogix 36X Manuale utente

Interlogix

Interlogix TruVision 5 Series Foglio di istruzioni

Interlogix

Interlogix 4 SERIES Foglio di istruzioni

Interlogix

Interlogix TruVision 4 IP Series Foglio di istruzioni

Interlogix

Interlogix TruVision TVD-2401 Manuale utente

Interlogix

Interlogix UVC-XP4DN-HR-P Manuale utente

Interlogix

Interlogix TruVision TVA-1101 Manuale utente

Interlogix

Interlogix TruVision Line Manuale

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente