Interlogix UVC-XP4DN-HR Manuale utente
UVC-XP4DN-HR(-P)
Camera Quick Start
Guide
P/N 1079203A-EN • REV 1.0 • ISS 20DEC11
Copyright © 2011 UTC Fire & Security. All rights reserved.
Trademarks and
patents
Interlogix, and UltraView names and logos are trademarks of
UTC Fire & Security.
Other trade names used in this document may be trademarks
or registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
N4131
FCC compliance Class A: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
ACMA compliance Notice! This is a Class A product. In a domestic environment
this product may cause radio interference in which case the
user may be required to take adequate measures.
Canada This Class A digital apparatus complies with Canadian ICES-
003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-0330 du Canada.
European Union
directives
12004/108/EC (EMC directive): Hereby, UTC Fire & Security
declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive
2004/108/EC.
2002/96/EC (WEEE directive): Products marked with this
symbol cannot be disposed of as unsorted municipal waste in
the European Union. For proper recycling, return this product to
your local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.
Contact
information
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.
Quick Start Guide 3 EN
Content
Package contents 3
Installation 3
Video connections 4
Set the lens mode 4
Attach the lens 5
Connect power 6
Mount the camera 6
Connect the monitor 7
Programming 7
OSD controls 7
Main menu 7
Specifications 9
Menu map 12
Package contents
Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use the unit;
contact the supplier immediately. If the unit is returned, it must be
shipped back in its original packaging.
Package contents:
Multilingual Quick Start Guide
CD with User Manual in several languages
Camera
C-mount adaptor
CAUTION: Use direct plug-in UL listed power supplies marked Class
2 or LPS (limited power source) of the required output rating as listed
on the unit.
Installation
This section provides information on how to install the camera.
EN 4 Quick Start Guide
Video connections
Figure 1: Making the video connections
1. Connect a coaxial cable terminated with BNC connectors between
the MON OUT connector of the camera and the video in connector
on a test or local monitor.
2. Connect a coaxial cable terminated with BNC connectors between
the VIDEO OUT connector of the camera and the video in
connector on a monitor, multiplexer, switcher, or other standard
video device.
Set the lens mode
If your lens has a manual iris, ignore this switch. It is for autoiris lenses
only.
Figure 2: Lens mode DIP switch and iris level adjustment
1. Set to VD (video drive) for autoiris lenses with built-in amplifier.
2. Set to DD (direct drive) for autoiris lenses without amplifier.
3. DD adjustment.
Quick Start Guide 5 EN
Note: When the lens mode DIP switch is set to DD, you can use the
DD level screw (iris level adjustment) to ensure the correct exposure of
images for the camera’s position and the lighting conditions. Use an
insulated tool to rotate the screw. Observe the results on the monitor
screen for the best setting.
Attach the lens
Refer to the instructions that came with the lens you purchased for
complete installation instructions of that lens.
Note: For optimal performance, use an autoiris lens.
Figure 3: Attaching your lens
Video-type autoiris lens leads DC-type autoiris lens leads
C-mount adapter
(for C-mount lenses only)
A E
B F
C G
D H
Camera Autoiris, lens
connector
Autoiris lens
plug
Lens (autoiris shown);
manual iris has no
cable
Video-type autoiris lens leads: A. Red (9 VAC); B. NC (no connection); C. Black
(ground); D. White (video)
DC-type autoiris lens leads: E. Damping coil (+); F. Damping coil (-); G. Driving coil
(+); H. Driving coil (-)
1. If you are using a C-mount lens, screw on the provided C-mount
adapter.
2. Screw your customer-supplied lens onto the camera.
EN 6 Quick Start Guide
3. If you are using an autoiris lens, insert the autoiris lens plug into
the autoiris lens connector.
Connect power
Caution: Use direct plug-in UL listed power supplies marked Class 2
or LPS (limited power source) of the required output rating as listed on
the unit.
Figure 4: Power connection
1. With a screwdriver, loosen the GND and ~AC24V/DC12V terminal
screws on the terminal block.
2. Connect a universal 12 VDC, 24 VAC power supply to the terminal
block.
Note: The terminal block is not polarity- sensitive. Either power lead
can be connected to either terminal connector. There is no need for an
isolated ground wire. The two power terminals can accept any polarity
and any combination of power that equals 12 VDC or 24 VDC.
3. Retighten the terminal screws until snug, ensuring that the power
leads are secure.
4. Supply power to the unit by plugging the power supply into a
proper source.
Note: The power LED illuminates to show that the camera is receiving
power. If it does not illuminate, check the terminal block connections
and the power source
Mount the camera
To mount the camera, attach the camera to the mounting surface using
the appropriate fasteners.
Quick Start Guide 7 EN
Connect the monitor
Program the cameras by attaching a standard video monitor to the
system.
To connect the monitor, do the following:
1. Plug the monitor output cable to the video monitor output
connector (see Figure 1 on page 4.)
2. Connect the BNC cable to the video monitor.
3. Press Enter (Figure 5 below) to display the Setup menu.
Programming
OSD controls
Use the OSD (on-screen display) setup menus to program the camera.
See Figure 5.
Note: If you do not press a button for two minutes, your changes are
saved, and the camera returns to its normal function.
Figure 5: OSD menu controls
Up
Down
Enter
Left
Right
Note: Wherever the PREVIOUS PAGE option appears, use it to leave
the current menu and return to the previous menu. Move to the
PREVIOUS PAGE option and press the center button.
Main menu
The camera is configured through the setup menus which appear on-
screen.
EN 8 Quick Start Guide
To access and navigate the main menu, press and hold the center
button of the OSD (See Figure 5). Use the up or down buttons to move
between items, and press the center button to select that item. Use the
left and right buttons to select the different options available for the
item.
You can return to the previous menu from any of the menus (except
the Main menu) by selecting the Previous page option.
There is a menu map on the back page of the manual that shows an
overview of the menus.
Refer to the User Manual for detailed programming instructions.
Figure 6: Main menu
Table 1: Main menu options
Menu option Function
Presets Configures the preset for the lighting condition.
Setup Configures camera ID, video I/O, type of lens, motion
detection, and wide dynamic range options.
Viewing Configures flip, resolution, gamma correction, image
sharpness, and saturation settings.
Exposure Configures automatic gain control (AGC), AE
preferences, range, shutter limit, and advanced
exposure limits.
White balance Configures white balance (WB) mode, magenta control,
WB bias, and auto tracking white balance.
Save/restore Displays firmware version, resets camera, saves user
settings, restores user settings, and restores factory
settings.
Exit Exits the OSD menu system.
Quick Start Guide 9 EN
Specifications
Electrical
Power Input 12 VDC or 24 VAC
Power consumption 3W (DC); 2.4 W (AC)
Environmental and physical
Weight 33.8 oz. (958 g)
Dimensions 5.22 x 4.11 in. (133 x 105 mm)
Operating temperature -58 to +122°F (-50 to +50°C)
Weather resistant IP66
EN 10 Quick Start Guide
Altri manuali per UVC-XP4DN-HR
2
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Interlogix Telecamera di sicurezza
Interlogix
Interlogix UltraView PTZ Manuale utente
Interlogix
Interlogix TruVision TVD-6120VE-2 Manuale utente
Interlogix
Interlogix TruVision TVB 2102 Manuale utente
Interlogix
Interlogix TruVision Line Manuale utente
Interlogix
Interlogix TVB-5301 Manuale utente
Interlogix
Interlogix TruVision TVD-2401 Manuale utente
Interlogix
Interlogix TruVision TVB-4402 Manuale utente
Interlogix
Interlogix TruVision TVD-N210V-2-N(-P) Manuale utente
Interlogix
Interlogix TruVision 5 Series Foglio di istruzioni
Interlogix
Interlogix TVP-6102 Manuale utente
Interlogix
Interlogix TruVision TVW-2401 Manuale utente
Interlogix
Interlogix TruVision TVC-7120-1-N Manuale utente
Interlogix
Interlogix TruVision Line Manuale utente
Interlogix
Interlogix TVD-5110-3 Manuale utente
Interlogix
Interlogix TruVision TVB-6102 Manuale utente
Interlogix
Interlogix TruVision TVB-5702 Foglio di istruzioni
Interlogix
Interlogix UVD-XP4DNR(-P) Manuale utente
Interlogix
Interlogix TruVision TVP-5201 Foglio di istruzioni
Interlogix
Interlogix TruVision TVB-2401 Manuale utente
Interlogix
Interlogix TVD-6120VE-2-N Manuale utente
