Intermec 3400 Manuale utente

3400, 3440, and 3600

Bar Code Label Printer

P/N 065145-001

User’s Manual

Intermec Technologies Corporation

6001 36th Avenue West

P.O. Box 4280

Everett, WA 98203-9280

U.S. technical and service support: 1-800-755-5505

U.S. media supplies ordering information: 1-800-227-9947

Canadian technical and service support: 1-800-687-7043

Canadian media supplies ordering information: 1-800-267-6936

Outside U.S. and Canada: Contact your local Intermec service supplier.

The information contained herein is proprietary and is provided solely for the purpose of allowing

customers to operate and/or service Intermec manufactured equipment and is not to be released,

reproduced, or used for any other purpose without written permission of Intermec.

Information and specifications in this manual are subject to change without notice.

1998 by Intermec Technologies Corporation

The word Intermec, the Intermec logo, JANUS, IRL, TRAKKER, Antares, Adara, Duratherm,

EZBuilder, Precision Print, PrintSet, Virtual Wedge, and CrossBar are trademarks of Intermec

Technologies Corporation.

The name Centronics is wholly owned by GENICOM Corporation.

IBM is a registered trademark of International Business Machines Corporation.

Throughout this manual, trademarked names may be used. Rather than put a trademark () symbol

in every occurrence of a trademarked name, we state that we are using the names only in an

editorial fashion, and to the benefit of the trademark owner, with no intention of infringement.

The software contained in the 3400, 3440, and 3600 Printers and the accompanying materials are

copyrighted. Unauthorized copying of the software, including software that has been modified,

merged, or included with other software, or the written materials is expressly forbidden without the

prior written consent of Intermec. All right, title, and interest in all copies of this software are and

shall at all times remain the sole and exclusive property of Intermec. Customers may be held legally

responsible for any copyright infringement that is caused or encouraged by their failure to abide by

these terms.

Contents

iii

Contents

Before You Begin vii

Warranty Information vii

Safety Summary vii

Warnings and Cautions viii

About This Manual ix

Other Intermec Manuals xi

Getting Started

Using This Manual 1-3

Getting to Know Your Printer 1-3

Preparing the Printer for Installation 1-5

Plugging In the Printer 1-5

Opening the Printer 1-6

Loading Media for Fanfold Printing 1-7

Printing the Hardware Configuration Test Label 1-9

What the Hardware Configuration Test Label Tells You 1-10

If a Hardware Configuration Test Label Does Not Print 1-10

Connecting the Printer to Your System 1-10

Connecting Your Printer to a PC 1-11

Connecting the Printer to a PC Serial Port 1-11

Connecting the Printer to a PC Parallel Port 1-12

Connecting Your Printer to a Network 1-12

Connecting the Printer to an AS/400 1-14

Connecting the Printer to a Mainframe 1-14

Cabling in Noisy Electrical Environments 1-14

Configuring the Serial Port for Communications 1-15

Verifying Printer Communications With Your System 1-18

Operating the Printer

Learning How to Operate the Printer 2-3

Understanding the Front Panel 2-3

Understanding the Front Panel LEDs 2-4

Using the Feed/Pause Button 2-5

3400, 3440, and 3600 Bar Code Label Printer User’s Manual

Loading Media Into the Printer 2-6

Loading Roll Media for Straight-Through Printing 2-6

Loading Media for Self-Strip Printing 2-8

Loading Thermal Transfer Ribbon 2-10

Setting the Media Sensitivity Number 2-12

Setting the MSN for Intermec Media and Ribbon 2-13

Setting the MSN for Other Media and Ribbon 2-14

Communicating With the Printer 2-18

Using the PrintSet Software 2-18

Using Third-Party Software 2-18

Using Intermec Printer Language (IPL) Commands 2-18

Printing a Test Label 2-19

Maintaining the Printer

Inspecting the Printer 3-3

Tools for Cleaning the Printer 3-3

Maintenance Schedule 3-4

Cleaning the Printhead 3-6

Cleaning the Printer Covers 3-7

Cleaning the Drive Roller and Tear Bar 3-8

Cleaning the Media Guides and Media Path 3-9

Cleaning the Label Sensors 3-10

Troubleshooting

Troubleshooting Checklist 4-3

Printer Operation Problems 4-3

Print Quality Problems 4-5

Communication Problems and Preventing Data Loss 4-7

Optimizing Printer Performance

Optimizing and Maintaining Print Quality 5-3

Correcting Uneven Print Quality 5-3

Contents

Adjusting the Print Darkness 5-5

Adjusting the Label Mark Sensor 5-6

Using the Printer Memory Efficiently 5-8

How Is the Printer RAM Used? 5-8

Making the Most of Your RAM 5-9

Increasing Throughput 5-10

What Is an Image Band? 5-10

How Does the Image Bands Command Work? 5-10

Optimizing Print Speed and Image Band Setting 5-11

Optimizing Image Bands for Batch Printing 5-11

Using Test and Service Mode

Using Test and Service Mode Procedures 6-3

Printing Test Labels 6-5

Using Data Line Print 6-5

Performing Selective Transfer 6-6

Resetting the Memory on Your Printer 6-7

Setting Configuration Commands in Test and Service Mode 6-8

Setting the Number of Dot Increments 6-9

Adjusting the Label Rest Point 6-11

Setting Emulation Mode 6-13

Using Forms Adjust 6-14

X Forms Adjust 6-15

Y Forms Adjust 6-16

Specifications

Printer Specifications A-3

3400 Specifications A-4

3440 Specifications A-6

3600 Specifications A-8

Printer Options A-10

Memory Expansion and Fonts A-10

Communication Interface A-10

Finishers A-11

Bar Code Symbologies Supported A-13

3400, 3440, and 3600 Bar Code Label Printer User’s Manual

Character Sets

International Character Sets B-3

Advanced Character Table B-3

Emulation Mode Character Table B-4

IBM Translation Character Table B-4

Code Page 850 Character Table B-5

Extended Character Sets B-6

Communications Reference

Communication Protocols C-3

Intermec Standard Protocol C-3

XON/XOFF Protocol (Software and Hardware Flow Control) C-4

XON/XOFF, No Status Protocol C-5

Polling Mode D C-5

Multi-Drop Protocol C-5

User-Defined Protocol C-6

Host Requirements C-7

Communications Boundaries C-7

Communications Interfaces C-7

RS-232 Serial Interface C-7

RS-422 Serial Interface C-8

RS-485 Serial Interface C-8

Printer Serial Port C-11

Full ASCII Table

Glossary

Index

HelvC

NugFont

Code39

Before You Begin

vii

Before You Begin

This section introduces you to standard warranty provisions, safety

precautions, warnings and cautions, document formatting conventions, and

sources of additional product information. A documentation roadmap is also

provided to guide you in finding the appropriate information.

Warranty Information

To receive a copy of the standard warranty provision for this product, contact

your local Intermec sales organization. In the U.S. call 1-800-755-5505, and in

Canada call 1-800-688-7043. Otherwise, refer to the Worldwide Sales & Service

list that was shipped with this manual for the address and telephone number of

your Intermec sales organization.

Safety Summary

Your safety is extremely important. Read and follow all warnings and cautions

in this book before handling and operating Intermec equipment. You can be

seriously injured, and equipment and data can be damaged if you do not follow

the safety warnings and cautions.

Do not repair or adjust alone Do not repair or adjust energized equipment alone

under any circumstances. Someone capable of providing first aid must always

be present for your safety.

First aid Always obtain first aid or medical attention immediately after an

injury. Never neglect an injury, no matter how slight it seems.

Resuscitation Begin resuscitation immediately if someone is injured and stops

breathing. Any delay could result in death. To work on or near high voltage,

you should be familiar with approved industrial first aid methods.

Energized equipment Never work on energized equipment unless authorized

by a responsible authority. Energized electrical equipment is dangerous.

Electrical shock from energized equipment can cause death. If you must

perform authorized emergency work on energized equipment, be sure that you

comply strictly with approved safety regulations.

3400, 3440, and 3600 Bar Code Label Printer User’s Manual

HelvC

NugFont

Code39

viii

Warnings and Cautions

The warnings and cautions in this manual use the following format.

Warning

A warning warns you of an operating procedure, practice, condition, or

statement that must be strictly observed to avoid death or serious injury to

the persons working on the equipment.

Avertissement

Un avertissement vous alerte d’une procédure de fonctionnement, d’une

méthode, d’un état ou d’un rapport qui doit être strictement respecté pour

éviter l’occurrence de mort ou de blessures graves aux personnes manupulant

l’équipement.

Caution

A caution alerts you to an operating procedure, practice, condition, or

statement that must be strictly observed to prevent equipment damage or

destruction, or corruption, or loss of data.

Conseil

Une précaution vous avertit d’une procédure de fonctionnement, d’une

méthode, d’un état ou d’un rapport qui doit être strictement respecté pour

empêcher l’endommagement ou la destruction de l’équipement, ou l’altération

ou la perte de données.

HelvC

NugFont

Code39

Before You Begin

About This Manual

Analysts and programmers should use this manual to learn how to operate,

program, and connect the 3400, 3440, or 3600 printer to a network or system.

The first part of this manual tells you how to install, operate, maintain, and

troubleshoot your printer. The last part of the manual covers advanced features

of the 3400, 3440, and 3600 printers. A basic understanding of DOS,

programming, and data communications is necessary.

What You Will Find in This Manual

This table summarizes the information in each chapter of this manual:

For Information On Refer To

Installing the printer Chapter 1, “Getting Started.” Tells you how to plug in the

printer, load fanfold media, configure the serial port, and

print a configuration test label.

Operating the printer Chapter 2, “Operating the Printer.” Explains the printer front

panel, tells you how to load roll media, load ribbon, test for

communications, and download fonts.

Routine maintenance Chapter 3, “Maintaining the Printer.” Shows how to maintain

the printer.

Troubleshooting Chapter 4, “Troubleshooting.” Instructs how to clear error

messages and troubleshoot programming or configuration

problems.

Improving printer

performance Chapter 5, “Optimizing Printer Performance.” Tells you how

to fine-tune the printer to increase processing time.

Test and Service

features Chapter 6, “Using Test and Service Mode.” Provides

information on using Test and Service mode to print test

labels, perform Test and Service mode procedures, and

configure DIP switch settings.

Specifications Appendix A.

Character sets Appendix B.

Communications Appendix C.

Full ASCII chart Appendix D.

3400, 3440, and 3600 Bar Code Label Printer User’s Manual

HelvC

NugFont

Code39

Terms and Conventions

Listed below are special terms and conventions used throughout the manual.

Refer to the glossary for a complete list of terms found in this manual.

Terms

“Printer” refers to a 3400, 3440, or 3600 bar code label printer.

“Media” is the label stock on which the printer prints labels.

“Host” refers to a personal computer or other computer that communicates

with the printer.

A “symbol” or “bar code symbol” consists of alphanumeric characters encoded

in a bar code format.

Conventions

The following conventions are used throughout this manual for operating

procedures and descriptions of the printer.

• Feed/Pause refers to the Feed/Pause button on the printer front panel.

• Downloaded commands appear in the order that you enter them into the

printer with the following conventions:

Convention Description

< > Angle brackets < > enclose mnemonic representations of ASCII control

characters. For example, <ETX> represents the ASCII “End of Text”

control character.

data Italic text represents variable data, which you must replace with a real

value. For example, nsignifies a variable for which you must designate a

constant value.

[data] Italic text within brackets represents optional data.

Ctrl Bold text represents a key on your keypad. For example, Tab represents

the Tab key and Mrepresents the letter M key.

Ctrl-ZWhen two keys are joined with a dash, press them simultaneously. For

example, if you see the command Ctrl-C, press the two keys at the same

time.

E3;F3 Type all characters that appear in the Courier font by pressing an

individual key on the keypad.

Altri manuali per 3400

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Intermec Etichettatrice

Intermec

Intermec EasyCoder 501XP Manuale utente

Intermec

Intermec EasyCoder PX6i Manuale utente

Intermec

Intermec 3600 Manuale utente

Intermec

Intermec PC23 Manuale utente

Intermec

Intermec 4400 Manuale utente

Intermec

Intermec PB50 Manuale utente

Intermec

Intermec PB22 Manuale utente

Intermec

Intermec EasyCoder PC41 Manuale utente

Intermec

Intermec PB22 Manuale utente

Intermec

Intermec EasyCoder PD41 Manuale utente

Intermec

Intermec PM43 Manuale utente

Intermec

Intermec EasyCoder 201II Manuale utente

Intermec

Intermec PB50 Manuale utente

Intermec

Intermec EasyCoder PC4 Manuale utente

Intermec

Intermec PC23 Manuale utente

Intermec

Intermec EasyCoder 4420 Manuale utente

Intermec

Intermec PB22 Manuale utente

Intermec

Intermec EasyCoder 501XP Manuale utente

Intermec

Intermec EasyCoder PX6i Manuale utente

Intermec

Intermec EasyCoder 3400e Manuale utente

Intermec

Intermec EasyCoder E4 Manuale utente

Intermec

Intermec EasyCoder PD4 Manuale utente

Intermec

Intermec 3240 Manuale utente

Intermec

Intermec EasyCoder E4 Manuale utente

Manuali Etichettatrice popolari di altre marche

Brother

Brother P-Touch 2420PC Manuale utente

newell

newell Dymo LabelManager 210D Manuale utente

Brother

Brother TD-4000 Manuale utente

U-Line

U-Line BROTHER H-8754 Manuale utente

Tharo Systems

Tharo Systems H-435+ Manuale utente

Brother

Brother E300 Manuale utente

Godex

Godex RT700 SERIES Manuale utente

ID Technology

ID Technology 252 Manuale utente

Labelmate

Labelmate MC-11 Manuale utente

CAB

CAB XD4M/300 Manuale utente

Avery Dennison

Avery Dennison Pathfinder 6057 Manuale di servizio

Brother

Brother P-touch PT-9700PC Manuale utente

TSC

TSC PEX1000 Series Manuale utente

Adkins

Adkins Label Master Manuale utente

Epson

Epson LabelWorks LW-400 Manuale utente

Primera

Primera 510212 Manuale utente

Brady

Brady BradyPrinter S3100 Manuale utente

DuraLabel

DuraLabel LabPRO Manuale utente