Intermec EasyLAN 100I Manuale utente
EasyLAN 100i
Ethernet Interface Board
Installation Instructions
P/N 1-960475-00
Edition 1
May 2000
Intermec EasyLAN 100i – Installation Instructions Ed. 1
1
Chapter 1
1. Introduction
Contents
1. Introduction
Table of Contents....................................................................... 1
Copyright Information ............................................................... 2
Trademarks ................................................................................ 2
Description ................................................................................ 3
Printer Firmware ........................................................................3
Installation Kit ........................................................................... 3
2. Physical Installation
EasyCoder XP-Series................................................................. 4
EasyCoder F-Series.................................................................... 7
3. Connection
Connection Printer to Network................................................. 10
4. Communication Setup
Assigning an IP Address .......................................................... 11
- Setting the IP address manually from the Setup Mode .......... 11
- Setting the IP address automatically from the Setup Mode.... 13
- Reading an Assigned IP Address .......................................... 15
Setup Mode Overview ............................................................. 16
Printing Test Label #6.............................................................. 17
Checking the Communication .................................................. 18
Intermec EasyLAN 100i
Installation Instructions
Edition 1, May 2000
Part No. 1-960475-00
2
Intermec EasyLAN 100i – Installation Instructions Ed. 1
Chapter 1 Introduction
Information in this manual is subject to change without prior notice and does not represent a commit-
ment on the part of Intermec Printer AB.
© Copyright Intermec Printer AB, 2000. All rights reserved. Published in Sweden.
The word Intermec, the Intermec logo, EasyCoder, EasyLAN, and Fingerprint are either trademarks or
registered trademarks of Intermec Technologies Corp.
DOS, Ethernet, HP, JetAdmin, LAN Manager, LAN Server, NDPS, Novell NetWare, OS/2, Unix, Win-
dows, AXIS NetPilot, and AXIS ThinServer are registered trademarks of the respective holders.
Throughout this manual, trademarked names may be used. Rather than put a trademark (™or ®) symbol
in every occurrence of the trademarked name, we state that we are using the names only in an editorial
fashion, and to the benefit of the trademarked owner, with no intention of infringement.
Intermec EasyLAN 100i –Installation Instructions Ed. 1
3
Chapter 1 Introduction
Attaching your EasyCoder 501XP, 601XP, F2 & F4 label printers
to the network has just become easier with Intermec’s EasyLAN
100i Ethernet interface. In addition, the EasyLAN 100i interface
board provides you with the most advanced network management
capa-bilities ever offered. The EasyLAN 100i interface is designed
to accommodate your network. With the most robust network sys-
temssupporteverofferedyourlabelprinterswillbeupandrunning
on your network in minutes.
Save time, space and money by putting the printer where you need
it. No need for a dedicated PC work-station or long serial or paral-
lel cables. Simply locate your label printer in the most efficient
place for your business, connect your RJ-45 network cable to the
printer and begin printing. Now you can print from workstations or
servers anywhere across the LAN, WAN, Intranet, or Internet. In
addition, you can monitor the status of print jobs from your Intranet
or Internet, any place any time using your favorite web browser.
Now you can take full advantage of the incredible bandwidth of
your 100baseTX Fast Ethernet network infrastructure. When you
combine the EasyLAN ETRAX 100 network processor with the
EasyCoder 501XP, 601XP, F2, or F4’s 32 bit RISC processor, print
jobs, including complex labels with bar codes, text and graphics,
are sent to the printer at lightning speed providing you with full
rated printer performance.
When your business depends on your label printer, you can depend
onthe IntermecEasyLAN100i Ethernetnetworkinterface boardto
provide you with dependable service and advanced management
capabilities.
The printer must be fitted with Intermec Fingerprint v. 7.31 or later.
The Ethernet port is addressed as device "net1:" (communication
channel #5).
The EasyLAN 100i kit contains:
• One EasyLAN 100i Ethernet interface board.
• One cover plate (used in EasyCoder XP-series printers only).
• One flat cable (used in EasyCoder F-series printers only)
• One CD-ROM with software and manuals
• This Installation Instruction booklet
The only tools required for the installation are #T10 and #T20Torx
screwdrivers.
Description
Printer Firmware
Installation Kit
4
Intermec EasyLAN 100i –Installation Instructions Ed. 1
Chapter 2
If the EasyLAN 100i interface board alredy is installed in your
printer, please bypass this chapter and continue at chapter 3.
ThisdescriptionappliestoIntermecEasyCoder501XPandIntermec
EasyCoder 601 XP only.
•Important! Turn off the power and disconnect the power cord.
The electronics compartment contain high voltage components
and wires. Do not open the electronics compartment before the
printer is safely disconnected from any mains supply.
• Open the right-hand door.
• Remove the four #T10 Torx screws along the lower edge of the
cover over the electronics compartment.
• Remove the four #T10 Torx screws that hold the upper edge of
the same cover.
• Remove the cover and put it aside e.g. on a soft cloth to avoid
scratches.
EasyCoder
XP-Series
#T10 Torx screws (4x)
#T10 Torx screws (4x)
2. Physical Installation
Intermec EasyLAN 100i –Installation Instructions Ed. 1
5
Chapter 2 Physical Installation
• Remove the four #T10 Torx screws that hold the interface cover
plate above the Centronics connector on the printer's rear plate.
Remove the cover plate.
• Save the cover plate for possible later use. Keep the screws.
• Insert the EasyLAN 100i interface board with the components
side facing right, as seen from behind. Check that the board fits
into the two square cut-outs on the left side of the slot.
• Attach the EasyLAN 100i interface board to the printer's rear
plate by means of two of the screws left over when you removed
the original cover plate.
EasyCoder
XP-Series, cont’d.
#T10 Torx screws (4x)
Cover Plate
EasyLAN 100i Interface Board
6
Intermec EasyLAN 100i –Installation Instructions Ed. 1
Chapter 2 Physical Installation
• Using the remaining two screws, attach the narrow cover plate
included in the delivery so it covers the right side of the slot.
• Connect the cable running from P81 on the CPU board to con-
nector P31 on the Ethernet Interface Board.
• Putbackthecoveroverthe electronicscompartment.Press firmly
to compress the leaf springs along the front and rear edges of the
electronics compartment.
Now you have one physical network connection on the printer's
rearplatein addition to the standard serial interface "uart1:" and the
standardparallelinterface"centronics:". Please continue at chapter
3for instructionsonhow toestablish communicationwiththeTCP/
IP network.
EasyCoder
XP-Series, cont’d.
IC304
IC305
P32
P35
1-971600-01 P01
P81
C1
C2
C3
C4
C12
C13
C70
D10
D30
F1
IC1
IC2
IC3
IC4
IC5
IC6
IC7
IC8
IC30
IC31
IC32
IC33 IC34
IC35
IC36
IC37
IC50
IC51
P11
P12
P30 P31
P32 P33P34
P35
P36
P37
P50
R1
R4
R6 R7
R8
R9
R10
R11
R12
R14
R52
R53
R56
R62
R63
R70
R72R73
R75
R76
SW10
C
A
B = EEPROM LOAD
A = PROGRAM LOAD
FPGA START MODE STRAPS
B
B
B
A
A
A
BOOT STRAP
1-971614-00 P02
P31
Intermec EasyLAN 100i –Installation Instructions Ed. 1
7
Chapter 2 Physical Installation
EasyCoder
F-Series
This description applies to Intermec EasyCoder F2 and Intermec
EasyCoder F4 only.
• Opentheelectronicscompartmentbyremovingthefont/left-hand
cover, which is held by three (3) #T20 Torx screws from the
paper compartment side of the centre-line wall.
•Important!
Turn off the power and disconnect the power cord.
The electronics compartment contain high voltage components
and wires. Do not open the electronics compartment before the
printer is safely disconnected from any mains supply.
#T20 Torx screws (x3)
8
Intermec EasyLAN 100i –Installation Instructions Ed. 1
Chapter 2 Physical Installation
• Remove the two #T10 Torx screws that hold the interface cover
plate on the printer's rear plate. Remove the cover plate.
• Save the cover plate for possible later use. Keep the screws.
• Insert the EasyLAN 100i interface board with the components
side facing right, as seen from behind.
• Attach the EasyLAN 100i interface board to the printer's rear
plate by means of the two screws left over when you removed
the original cover plate.
EasyCoder
F-Series, cont’d.
#T10 Torx screw
Cover Plate
#T10 Torx screw
EasyLAN 100i
interface pcb.
Intermec EasyLAN 100i – Installation Instructions Ed. 1
9
Chapter 2 Physical Installation
• Connectthe flatcableincludedinthe kitbetween connector P81
on the CPU board and connector P31 on the interface board.
• Make sure the cable runs as illustrated below.
• Put back the cover over the electronics compartment.
Now you have one physical network connection on the printer's
rearplate inadditionto thestandard serial interface"uart1:". Please
continueatchapter3forinstructionson how to establish communi-
cation with the TCP/IP network.
EasyCoder
F-Series, cont’d.
P35
IC305
P32
IC304
P33
P81
C1
C2
C3
C4
C12
C13
C70
D10
D30
F1
IC1
IC2
IC3
IC4
IC5
IC6
IC7
IC8
IC30
IC31
IC32
IC33 IC34
IC35
IC36
IC37
IC50
IC51
P11
P12
P30 P31
P32 P33P34
P35
P36
P37
P50
R1
R4
R6 R7
R8
R9
R10
R11
R12
R14
R52
R53
R56
R62
R63
R70
R72R73
R75
R76
SW10
C
A
B = EEPROM LOAD
A = PROGRAM LOAD
FPGA START MODE STRAPS
B
B
B
A
A
A
BOOT STRAP
1-971614-00 P02
P31
CPU Board
Interface Board
Cable
Altri manuali per EasyLAN 100I
1
Indice
Altri manuali Intermec Scheda di rete
Manuali Scheda di rete popolari di altre marche
Buffalo
Buffalo AirStation WLI-PCM-L11GP Manuale utente
National Instruments
National Instruments NI 9234 Manuale utente
Hama
Hama 49276 Manuale utente
Linksys
Linksys WCF54G - Wireless-G Compact Flash Card Manuale operativo
Compaq
Compaq Wireless LAN 100 Manuale utente
Bose
Bose PowerMatch Dante Manuale utente