Intermec EasyCoder PF2i Manuale utente

Installation

Instructions

Label Taken

Sensor Kit

(for EasyCoder PF2i,

PF4i, and PF4i Com-

pact Industrial)

Intermec Printer AB

Idrottsvägen 10

P.O. Box 123

S-431 22 Mölndal

Sweden

Service support: +46 31 869500

The information contained herein is proprietary and is provided solely

for the purpose of allowing customers to operate and/or service Intermec

manufactured equipment and is not to be released, reproduced, or used

for any other purpose without written permission of Intermec.

Information and speciﬁcations in this manual are subject to change

without notice.

EasyCoder and Fingerprint are registered trademarks of Intermec Tech-

nologies Corp. The word Intermec and the Intermec logo are trademarks

of Intermec Technologies Corp.

Torx is a registered trademark of Camcar Division of Textron Inc.

Throughout this manual, trademarked names may be used. Rather than

put a trademark (™) symbol in every occurrence of a trademarked name,

we state that we are using the names only in an editorial fashion, and to

the beneﬁt of the trademark owner, with no intention of infringement.

Preface

Contents

Introduction ................................................................................. iv

Printer Firmware........................................................................... iv

Installation Kit.............................................................................. iv

1 Physical Installation

Installation Instructions .................................................................2

2 Controlling and Adjusting the LTS

Intermec Fingerprint v8.xx.............................................................6

IPL v2.xx .......................................................................................7

Label Taken Sensor Kit Installation Instructions iii

Preface

iv Label Taken Sensor Kit – Installation Instructions

Introduction

This Installation Instructions booklet describes how to install a label

taken sensor (LTS) in an EasyCoder PF2i, PF4i, or PF4i Compact Indus-

trial printer, how to adjust the sensitivity, and how to control it in either

Intermec Fingerprint or IPL.

The label taken sensor enables the printer’s ﬁrmware to detect if the

latest printed label (or similar) has been removed before starting to print

next label. It consists of a light-emitting diode (LED) and a photoelec-

tric sensor. The LED emits a narrow beam of light upwards towards the

media outfeed area. If the light is reﬂected back by a label, that has not

yet been removed, it will be detected by the sensor and a label-not-taken

condition is assumed. The theoretical point of detection is 20.7 mm

(0.81 in) outside the inner edge of the media path and immediately in

front of the tear bar.

This interface kit must only be physically installed by an

authorized service technician. Intermec assumes no respon-

sibility for personal injury or damage to the equipment if

the installation in performed by an unauthorized person.

Take precautions against electrostatic discharges, for

example by wearing grounded bracelets.

Printer Firmware

Intermec Fingerprint v8.00 (or later) or IPL v2.00 (or later).

Installation Kit

The Label Taken Sensor Kit contains:

•One sensor with cable and connector

•One bracket

•One #T10 Torx screw

•One Installation Instruction booklet

Tool requirements: #T10 and #T20 Torx screwdrivers.

Label Taken Sensor Kit Installation Instructions 1

1 Physical Installation

This chapter describes how to physically install the

Label Taken Sensor (LTS) kit in a PF2/4i-series

printer.

2 Label Taken Sensor Kit – Installation Instructions

Chapter 1 — Physical Installation

Installation Instructions

•Switch off the printer and disconnect the power cord.

•Disconnect all communication cables.

•Remove the bottom plate as follows.

The electronic compartment contains wires and compo-

nents with dangerous voltage (up to 380V). Make sure that

the printer is switched off and the power cord is discon-

nected before bottom plate is removed.

•Turn the printer upside down on a soft cloth or similar to avoid

scratches.

•Using a #T20 Torx screwdriver, remove the six screws indicated below

and lift away the bottom plate and right-hand door assembly.

Label Taken Sensor Kit Installation Instructions 3

Chapter 1 — Physical Installation

•Fit the sensor and bracket to the lug at the printer’s front while rout-

ing the cable between the two rails on the center section and through

the slot in the center section as illustrated below.

•Connect the LTS cable to J53 at the lower edge of the CPU board.

The connector is marked “LTS.”

•Put back the bottom plate.

•Put the printer back on its feet and connect the power cord and all

communication cables.

Mounting lug

Sensor

Bracket

#T10 Torx screw

Cable to J53

on CPU board

Center section

Label Taken Sensor Kit – Installation Instructions

Chapter 1 — Physical Installation

Label Taken Sensor Kit Installation Instructions 5

2 Control and Adjustment

This chapter describes how to control and adjust the

label taken sensor in printers running either Intermec

Fingerprint v8.00 (or later) or IPL v2.00 (or later).

6 Label Taken Sensor Kit – Installation Instructions

Chapter 2 — Control and Adjustment

Intermec Fingerprint

Controlling the LTS

The label taken sensor can be enabled using the instructions LTS& ON

and LTS&OFF respectively. The status of the LTS can be polled using

the function PRSTAT. See Intermec Fingerprint v8.00, Programmer’s

Reference Manual.

Adjusting the LTS

The sensitivity of the Label Taken Sensor (LTS) may need to be adjusted

according to the ambient light conditions and the reﬂective character-

istics of the back side of the media. The sensitivity can be adjusted in

the Setup Mode or by using setup ﬁles or setup strings (see Intermec

Fingerprint v8.xx, Programmer’s Reference Manual). There are no straps or

potentiometers for adjusting the LTS.

In the Setup Mode, the LTS setup options are only displayed if an

optional label taken sensor is installed in the printer. Also refer to the

User’s Guide, chapters “Setting Up the Printer”and “Setup Mode”for

instructions how to adjust the LTS.

•LTS Adjust:

Press <Enter>. A label is fed out. Remove the label and press <Enter>

again. A menu shows the sensitivity automatically selected by the ﬁrm-

ware and the range in which the LTS will work. Press <Enter> again

and you will proceed to the LTS Test menu.

•LTS Test:

Press <Enter>. A label is fed out. Remove the label and a new label

should be fed out automatically. Repeat until you are sure the LTS

works properly. Then press <Enter> to stop and exit.

•LTS Value:

Press <Enter>. You can enter a new value in the range indicated in the

LTS Adjust menu (see above). Min/max values are in the range 0-10.

Altri manuali per EasyCoder PF2i

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Intermec Accessori per stampanti

Intermec

Intermec EasyCoder 3400e Manuale utente

Intermec

Intermec EasyCoder PC4 Manuale utente

Intermec

Intermec EasyCoder 501 SA Manuale utente

Intermec

Intermec PM4I Manuale utente

Intermec

Intermec Font Card Manuale utente

Intermec

Intermec EasyCoder 501 SA Manuale utente

Intermec

Intermec 3240 Manuale utente

Intermec

Intermec EasyCoder PF2i Manuale utente

Intermec

Intermec PM4I Manuale utente

Intermec

Intermec EasyCoder PF8 Manuale utente

Intermec

Intermec 3600 Manuale utente

Intermec

Intermec EasyCoder F4 Manuale utente

Intermec

Intermec EasyCoder PF2i Manuale utente

Intermec

Intermec ESim v4.20 Manuale utente

Intermec

Intermec UBI EasyCoder 601 E Guida

Intermec

Intermec EasyCoder 3400d Manuale utente

Intermec

Intermec EasyCoder PF4i Manuale utente

Intermec

Intermec 869 RFID Reader Istruzioni operative

Intermec

Intermec 825-192-001 Manuale utente

Intermec

Intermec 4630 Manuale utente

Intermec

Intermec 3400 Manuale utente

Intermec

Intermec EasyCoder PF2i Manuale utente

Intermec

Intermec EasyCoder 601XP Manuale utente

Intermec

Intermec EasyCoder 501XP Manuale utente

Manuali Accessori per stampanti popolari di altre marche

Star Micronics

Star Micronics TSP800 Series Manuale utente

REA

REA JET HR pro 2K Manuale utente

HP Laserjet,Color Laserjet 4si Manuale utente

oliser

oliser MS 45 Manuale utente

Roland

Roland DU2-64 Istruzioni e ricette

Xerox

Xerox EFI EXP6000 Manuale utente

Canon

Canon Finisher-T1 Manuale utente

Sharp

Sharp FO-1MK Manuale utente

Labelmate

Labelmate PM-300 Manuale utente

Epson

Epson T6248 Manuale operativo

Epson

Epson OT-BZ20 Manuale utente

Canon

Canon TonerRobot EP-27 Manuale utente

Ricoh

Ricoh LCIT RT5100 Guida rapida

GBC

GBC 16 Series Manuale utente

Canon

Canon INNER 2-WAY TRAY-E1 Manuale operativo e di manutenzione

Develop

Develop SD-509 Manuale utente

Kyocera

Kyocera KM-6230 Manuale

Triumph Adler

Triumph Adler DF-710 Manuale