Intermec 681 Manuale utente
681/682/781T/782
40-Column
Printers
Quick Start Guide
681/682 and 781T/782 Printer Quick Start Guide
2
Packing List
Check to ensure that you receive these items:
IntermecR681 Printer
p/n 320-082-00x
Product Warranty Card
IntermecR682 Printer
p/n 320-083-00x
OR
Com
p
liance Statement
OR
IntermecR782 Printer
p/n 320-084-00x
with card reader p/n 320-084-003
IntermecR781T Printer
p/n 320-085-00x
681/682 and 781T/782 Printer Quick Start Guide
3
AC Wall Charger
p/n 851-060-002
Order power cord under
separate part number
Common Accessories Sold Separately
Mobile Computer to PrinterCable
p/n 226-469-001 (RJ-45 connector
on the printer end)
Cigarette Lighter Charger
p/n 852-043-001
p/n 321-578-001 (RJ-11 connector
on the printer end)
681/682 and 781T/782 Printer Quick Start Guide
4
Getting Started
Here are the main components of the IntermecR681 and 682
printers.
Cover Latch
Belt Clip (681)
Computer to Printer Jack
681/781T Printer Components
Paper Advance
Charger Jack
Printer Case Open
Printer Case Closed
Charge LED (red charging;
green complete)
Charge LED (red charging;
green complete)
Ribbon (Dot Matrix)
682/782 Printer Components
Paper Advance
Charger Jack
Terminal Holder
Computer Securing Tab
681/682 and 781T/782 Printer Quick Start Guide
5
Charging the Lithium Ion Batteries
"The printer battery charges in about 3 hours.
"You can charge both the Mobile Computer and the Printer
battery at the same time using the AC or Cigarette Light-
er Charger. The time to charge both batteries is about 8
hours.
Connecting Charger to Printers
Charger Jack
LED Battery Indicators
LED State of Charge Action
Solid Red In progress Waiting for green LED
Green Complete Remove charger
Red Flash slow Low temperature or
battery is
disconnected
Change environment or
connect battery
Red Flash fast High temperature Change environment
Red/Orange
slow
Low voltage Wait for solid red
Red/Orange
fast
High voltage Wait for solid red
Orange flash
slow
Timeout Restart charge
681/682 and 781T/782 Printer Quick Start Guide
6
Beep Indicators
Number of Beeps Indicates
One A) Printer has come out of sleep mode.
B) Using the 781T with wireless printing,
the radio when enabled but not put in use
for a while beeps every five minutes to let
you know it is enabled and also using
battery life.
Two Printer is out of paper.
Three Battery is low.
One long beep No program in printer, only boot code.
681/682 and 781T/782 Printer Quick Start Guide
7
Using Your Printer
Intermec
R
681 or 781T Printer
1. Attach the Mobile Computer to Printer cable. RJ-11 cable
p/n 321-578-001, RJ-45 cable p/n 226-469-001 .
2. As you use the printer the power comes from the battery
in the printer. When the printer battery runs down the
printer will not operate until the battery is recharged.
Attachin
g
Com
p
uter to Printer Cable
Computer to Printer Jack
Mobile Computer to Printer Cable
Intermec
R
682 or 782 Printer
1. Slide the mobile computer into the computer holder on
your printer.
2. To remove computer from the printer, lift the computer up
slightly to clear the computer securing tab and pull out.
Inserting and Removing Computer
681/682 and 781T/782 Printer Quick Start Guide
8
Using the Card Reader
Slide the card down into the reader with the magnetic tape to
the right side. The magnetic card must meet the following ISO
standards: 7810 (physical characteristics) 7811 (recording tech-
niques) and 7816 (smart card standards)
Using the Card Reader
Paper Changing
Installing new paper roll
681/682 and 781T/782 Printer Quick Start Guide
9
781T Printer using Wireless Printing
IrDA/Wireless Mode
Your printer comes to you as an IrDA mode printer. To switch
the mode to Wireless Printing it is necessary to toggle the mode
via the self-test function of the printer.
Performing the self-test indicates the current mode of the
printer. The mode displays on the ticket and an audible indica-
tion sounds. Each time the self-test function is performed the
mode will toggle between wireless printing and IrDA modes.
781T Preparation
1. Prepare the 781T by holding down the red button for about
two seconds until you hear a short beep. This means the
printer is ready to go and will be discoverable.
Any time you press and hold the button until it beeps, you
will dump any active wireless printing sessions.
2. You are ready to print wireless transactions.
Printer Self-Test
1. Press the Paper Advance (red) button for at least five sec-
onds to run a Self-Test. This means you will be holding it
long enough to hear the beep and complete a paper advance.
The self-test indicates the current state of your printer.
Verify the current mode by reading the Power status line
from the printout. When your printer is turned off, the ra-
dio is undiscoverable and unconnectable.
2. When shipping your printer via air freight, turn the wire-
less printing mode off and set to IRDA so that the radio is
not powered
Why Printer Beeps Every 5 Minutes When Unconnected
As part of the implementation of the serial port service, this
service refreshes itself every five minutes. That refresh sends a
message to the printer, which then wakes up and causes the
beep while resynchronizing with the serial port service. The
printer then goes back to sleep based on its timeout. The beep
can be turned off within the ’printer configuration utility’.
681/682 and 781T/782 Printer Quick Start Guide
10
700 Mobile Computer Preparation
1. On your mobile computer, tap the Bluetoothticon located
in the System tray on the Today screen.
2. Select Advanced Features>Bluetooth Devices.
3. From the Tools menu, select Device Discovery. You are
presented with a couple of screens detailing the device dis-
covery process.
4. You are now presented with a screen allowing you to modify
the selection parameters. The default should work for your
needs.
5. Click Next to proceed. A search for Bluetooth devices is per-
formed followed by a look-up of discovered device names.
The progress bars indicate the inquiry status.
6. A list of discovered devices displays.
If your remote wireless printer is discovered and presented in
the list, select the appropriate check box and click Next.
If your remote device is not displayed, ensure that the device
and its radio are switched ON. Click Next, then select Finish.
7. A progress bar appears indicating Service Directory is being
performed.
If the discovery is successful a screen with Successful discovery
displays. Click Finish. The remote device icon appears in the
Bluetooth Devices Folder. Verify that this device was discov-
ered by looking at the properties (Device>Properties).
If the Services tab lists Portable Printer, the service was discov-
ered correctly.
If it doesn’t, select the Update button on the Services tab to try
to rediscover the services available (sometimes it will take a
couple tries to correctly discover the services).
8. Click Next twice, all Wireless Printing devices within range
will be discovered and displayed. You may have to repeat
this step from time-to-time.
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Intermec Stampante
Intermec
Intermec PW50 Manuale utente
Intermec
Intermec EasyCoder 201II Manuale
Intermec
Intermec EasyCoder F2 Manuale utente
Intermec
Intermec EasyCoder 101 Manuale
Intermec
Intermec EasyCoder 4420 Manuale utente
Intermec
Intermec PB50 Manuale utente
Intermec
Intermec 3240 Manuale di istruzioni
Intermec
Intermec EasyCoder 401 Manuale utente
Intermec
Intermec EasyCoder 501 SA Manuale utente
Intermec
Intermec EasyCoder E4 Manuale utente
Intermec
Intermec PR2 Manuale utente
Intermec
Intermec PW40A Manuale utente
Intermec
Intermec EasyCoder 4100 Manuale utente
Intermec
Intermec PF8D Manuale utente
Intermec
Intermec EasyCoder PL3 Manuale utente
Intermec
Intermec PR2 Manuale utente
Intermec
Intermec EasyCoder 101 Manuale utente
Intermec
Intermec EasyCoder 7421 Manuale
Intermec
Intermec 6822P Manuale utente
Intermec
Intermec PW50 Manuale utente
