InWin IW-RS248-03 Manuale utente
IW-RS248-03
User Manual
Table of Contents
PREFACE ..................................................................................................................................... 1
SAFETY INFORMATION ............................................................................................................... 1
CAUTION .................................................................................................................................... 2
SPECIFICATIONS .......................................................................................................................... 3
1 Product Introduction ........................................................................................................... 4
1.1 Box Contents ............................................................................................................... 4
1.2 General Information .................................................................................................... 5
1.2.1 Front Panel Controls and Indicators ................................................................................. 6
1.2.2 Rear Panel Configuration ................................................................................................. 7
2 Hardwar Installation ......................................................................................................... 8
2.1 Remo ing and Installing a Hard Dri e ........................................................................... 8
2.1.1 Installing a Hard Drive ...................................................................................................... 8
2.1.2 Removing a Hard Drive..................................................................................................... 9
2.2 Remo ing and Inserting the Top Co er ....................................................................... 10
2.3 Remo ing and Installing the Fan Module ................................................................... 12
2. .1 Removing the Fan Module ............................................................................................. 12
2. .2 Installing the Fan Module............................................................................................... 12
2.4 Remo ing and Installing the PSU Module ................................................................... 13
2.4.1 Removing the PSU Module ............................................................................................ 1
2.4.2 Installing the PSU Module .............................................................................................. 1
2.5 Installing Slide Rail .................................................................................................... 14
2.5.1 Identifying the Slide Rail ................................................................................................ 14
2.5.2 Take out the Inner Rail and Slide the Intermediate Rail Back ........................................ 14
2.5. Attach the Inner Rail to the Chassis ............................................................................... 15
2.5.4 Mount the Rail Bracket to the Cabinet .......................................................................... 16
2.5.5 Insert the Chassis to the Cabinet ................................................................................... 17
2.6 Installing the Motherboard ........................................................................................ 18
2.7 Connecting Cables ..................................................................................................... 18
2.7.1 Connecting expander through SAS connectors.............................................................. 18
2.7.2 Connecting LED, front control panel and front USB ....................................................... 19
3 Backplan Introduction ..................................................................................................... 20
4 Expand r Board Introduction ............................................................................................ 22
5 Compatibility Lists ............................................................................................................ 23
6 Q&A ................................................................................................................................. 23
7 T chnical Support .............................................................................................................. 24
1
PREFACE
Thank you for choosing InWin IW-RS248-0 . This manual is written for system technicians who are
responsible for installation, troubleshooting, managing and repairing this server chassis. This
document provides an overview of all the features of the chassis, a list of accessories or other
components you may need to finish the installation, troubleshooting methods and instructions on
adding and removing components on the InWin IW-RS248-0 . For the latest version of this manual,
you may visit InWin’s server website to download the latest updated version.
SAFETY INFORMATION
To ensure a safe and smooth operation of your InWin IW-RS248-0 , it is essential that you choose
an appropriate location for the system, provide an appropriate operating environment and supply
an adequate amount power for all components of the system. As you plan for installation, follow
the guidelines below to ensure that the system and its environment are safely and appropriately
positioned for efficient operation and service. Your system should be installed and serviced only by
a qualified technician.
En ironment selection: The system is designed to operate in a typical office environment:
•The location should be clean, dry and free of airborne particles.
•It should be a well-ventilated room, and away from sources of heat including direct sunlight
and radiators.
•It should be kept away from sources of vibration or physical shock.
•The space should be accommodated with a properly grounded wall outlet, and with sufficient
space to access the power supply cords.
•The operating environment temperature should be around 0°C to 40°C ( 2°F to 104°F).
Heed safety instructions: Before working with InWin IPC/Storage server products, we strongly
recommend you use this guide as a reference and follow the safety instructions. The instructions in
this manual will help you ensure and maintain compliance with existing product certifications and
approvals. Follow the described, regulated components mentioned in this manual. Use of non-UL
listing products or other regulators may not comply with product regulations in the region(s) in
which the product is sold.
System power on/off: The power button DOES NOT totally turn off the system AC power. To
remove the power of the system, you must unplug the AC power cord from the outlet or the
system’s power supply units. Make sure the power cord is unplugged before you open the chassis,
add or remove any components.
Hazardous conditions, de ices and cables: Hazardous electrical conditions can be present on/in
power supply units and their cables. Disconnect the power cord and any other device attached to
the server before opening the case. Failing to follow safety procedures will increase the risk of
personal injury or equipment damage.
2
Electrostatic discharge (ESD) and ESD protection: In most cases, ESD may damage disk drives,
electronic boards and other parts. We recommend that you conduct installation only at an ESD
free space. If not possible, perform ESD protection protocol by wearing an anti-static wrist straps
attached to the ground on any unpainted metal surface on your server during operation.
Installing or remo ing jumpers: A jumper is a short length conductor used to close, open or bypass
part of an electronic circuit. Jumpers on InWin backplanes have a small tab on top that you can
pick up with your fingertips. Grip the jumper carefully, and plug the jumper to cover the jumper
pins on the backplane. Once you need to remove the jumper, grip the jumper and carefully pull
without squeezing.
CAUTION
To avoid damage and maintain your safety, please read the following terms listed below:
1. No to populate hard drives and turn on the power before the system is settles
down.
Make sure hard drives and other components are properly connected before
turning on the system.
2. Tighten or loosen all the screws with a screwdriver.
. Apply the correct screws packed in the accessory box.
4. For your safety, please have at least two people lift and place the unit.
5. Before mounting the unit to the cabinet, make sure the rail is installed correctly.
6. When installing and removing any module or part, please use the handles.
SPECIFICATIONS
Model Name RS248-0
Standard EIA-RS 10D
M/B Form Factor ATX (12“ x 9.6”), CEB(12” x10.5”), EEB(12” x 1 ”)
Dimensions (D x W x H)
w/o Front Door 660mm x 482.6mm x 87mm (26” x 19” x .5”)
Dri e Bay External : Hot-swap 2.5” SSD/HDD (7mm) x 48 (U.2 NVMe x 8)
Rear hot-swap 2.5”SSD/HDD (7mm) x 2
Power Supply
Supports
▪ Form Factor : Platinum CRPS redundant with PDB cable management
▪ Watt: 1200W
Indicator Power LED; LAN1/LAN2/LAN /LAN4 LED ; System LED ; ID LED
Front Control Panel Power on/off; Reset; NMI; ID SW,USB .0 x 1; Mute button
Backplane 1 2 pcs of Mini-SAS HD 12Gb/s with expander plus SlimLine x 8
Backplane 2 2 pcs of Mini-SAS HD 12Gb/s with expander plus OcuLink x 8
Cooling Fan 80 x 8 mm PWM Fan x 4
Expansion Slot Low-Profile PCI Slot x 7
SAS 12G Expander 2 pcs of Mini-SAS HD connector (SFF-864 ) x (Host x2, Cascade x1)
Material Material: SGCC
Thickness: 1.0 mm
Rail Kit Supports 28" tool-less & ball-bearing slide rail
Packaging Dimensions
(D x W x H)
900 x 610 x 242 mm
Shipping Information Net Weight: 16.77kg
Gross Weight: 20.56kg
Container Information Single Packing with pallets
20’: 120 pcs
40’: 294 pcs
40’HQ: 78 pcs
* The actual product is subject to change without prior notice. InWin Development Inc. reserves the
right to make any final modifications.
* Above image is for reference only. All hardware components and optional parts are not included.
4
1Product Introduction
1.1 Box Contents
When you open the carton box of IW-RS248-0 , the contents should include:
5
1.2 General Information
When you open the chassis, it should reflect the diagram’s image
.
Rear top cover
CRPS Redundant module
power supply
48 x 2.5” 7mm
tool-less HDD trays
Front Controls and indicators
ATX or CEB & EEB
Motherboard
PWM Fan (Max. 4pcs)
Middle top cover
6
1.2.1 Front Panel Controls and Indicators
IW-RS248-0 supports SAS/SATA 48 x 2.5”(7mm) disk bays, or SAS/SATA 40 x
2.5”(7mm) with NVMe 8 x 2.5”(7mm) disk bays in specific location, and the control
panel, USB IO ports and indicators on the handles.
No.
Name Color
Status
Description
1 Power On/Off Button with LED
Blue Solid
on
System is powered on
N/A Off System is off
2 NMI Button N/A Press the button to activate user-define
function
System Reset Button N/A Press the button to activate system reset
4 Chassis ID Button with LED Blue Solid
on
Press the button to activate system
identification
5 System Fail LED Red Solid
on System Fault (Beeper)
6 LAN LED (From top to bottom
ranked LAN1 - LAN4)
Amber
Blink Link between system and network
N/A Off No date transmission or receiving is
occurring
9
9
7
7 Mute Button N/A Press the button to activate beeper mute
8 USB .0 Connector N/A USB devices connection
9 NVMe 8 x 2.5” (7mm) disk bays for faster hybrid storage performance.
1.2.2 Rear Panel Configuration
No.
Name Description
1 Power Module 1 Default primary power supply module
2 Power Module 2 Backup power supply module
System I/O
(depends on M/B specifications)
The I/O shield should come with the motherboard or is
provided by motherboard vendors
4 7 Low Profile PCI-E Slot The slot supports low profile cards. The bracket should
be removed before using.
5 OS HDD
This slot is for In Win OS disk backup module (option),
which supports two 2.5” 7mm SSDs and features
hot-swap function.
6 Phone Jack for RS2 2 It connects to expander via RS2 2 port, which supports
monitor expander status.
❶
❷
❸
❹
❺
❻
Indice
Altri manuali InWin Server di archiviazione di rete
InWin
InWin Cobra IW-RS424-07 Manuale utente
InWin
InWin IW-RS104-02M Manuale utente
InWin
InWin IW-RS108-07 Manuale utente
InWin
InWin IW-RS118-03 Manuale utente
InWin
InWin IW-RN224-03 Manuale utente
InWin
InWin IW-RS424-02M Manuale utente
InWin
InWin IW-RS436-07 Manuale utente
InWin
InWin IW-RS224-07 Manuale utente
Manuali Server di archiviazione di rete popolari di altre marche
HP
HP NetStorage 6000 Manuale utente
Seagate
Seagate U10 ST320423A Manuale utente
Synology
Synology RackStation RS816 Manuale
D-Link
D-Link ShareCenter Pro DNS-1200-05 Manuale utente
Avid Technology
Avid Technology VideoRAID ST Guida di sicurezza
Western Digital
Western Digital My Cloud Home Duo Manuale utente
