IOGear M1161 Manuale utente
Installation
Installation Guide
Universal Wireless-n Adapter
GWU627
PART NO. M1161
3
Table of Contents
Package Contents 4
System Requirements 5
Product Overview 6
Installation 8
Installation without WPS - Windows XP 10
Installation without WPS - Windows Vista 16
Installation without WPS - Windows 7 24
Installation without WPS - Mac 32
Manual Set Up 37
Firmware Upgrade 41
Federal Communications Commission
(FCC) Statement
46
CE Compliance 47
SJ/T 11364-2006 48
Limited Warranty 49
Contact 50
4
Package Contents
1x GWU627 client adapter•
1x USB power cable•
1x Ethernet cable•
1x Power adapter with USB port•
1x User Manual•
1x Warranty Card•
5
System Requirements
Operating System•
Windows XP, Windows Vista, Windows 7-
Mac OS X v10.4 and above-
Wireless network with WPS setup•
Wireless network without WPS setup and computer•
6
Product Overview
1. Ethernet Port The Ethernet port allows a LAN connection through Cat 5 cables.
Supports auto-sensing at 10/100M speed, half/ full duplex.
2. Mini USB Power The Mini USB cable provides power.
3. WPS Button Push and hold the WPS button for 5~10 seconds to enable the
WPS feature.
4. Reset Button Push and hold the reset button for 5~10 seconds to reset the adapt-
er to factory default settings.
1 2
3 4
7
1. Power LED On - The WLAN Broadband Router is powered on.
Off - The WLAN Broadband Router is powered off.
2. WLAN LED Flashing - WLAN is transmitting or receiving data.
Off - WLAN is off
3. WPS LED Flashing - The WPS feature is enables and in use.
Off - The WPS feature is not in use.
4. LAN LED Flashing - Data is transmitting or receiving on the LAN interface.
On - Port linked.
Off – No link.
LED Indicator State Description
1 2 3 4
8
Installation
Wireless Setup with WPS
Step 1: Power on your Universal WiFi Adapter using either of these methods:
•Connectthemini-USBcabletoadevicethatprovidesTypeAUSBconnection.Makesurethatthedevice
where you connect the USB cable is powered on.
•ConnecttheWiFiadaptertoanelectricaloutletwiththeincludedpoweradapter.
Note: It will take about 50 seconds to complete the boot-up sequence. When complete, PWR (power) LED
will be active, and the WLAN Activity LED will be blinking to show the WLAN interface is enabled.
Step 2: Use the included RJ-45 Ethernet cable to connect the WiFi adapter with your device such as
Blu-ray player, HDTV, or game console.
Step 3: Refer to your wireless router’s user manual to enable the WPS function, then press “WPS” button
on the top of WiFi adapter.
Your installation is complete. If asked for the type of connection, make sure “WIRED” is selected on your
device.
9
or
orororor
Step 1
Step 3
Step 2
10
Installation without WPS - Windows XP
Step 1: Turn off your computer’s wireless
connection (if applicable) and disconnect the
Ethernet cable currently connect to your computer
(if applicable).
Step 2: Use both the included RJ-45 Ethernet
cable and the USB cable to connect the WiFi
adapter with your computer.
Step 3: Set your computer with a static IP address.
a. Right click on “My Network Places” and select
“Properties”.
Indice
Altri manuali IOGear Adattatore
IOGear
IOGear GUC100KM Manuale utente
IOGear
IOGear GBU221 Manuale utente
IOGear
IOGear GWU635 Manuale utente
IOGear
IOGear GWU625 Manuale utente
IOGear
IOGear GPU202 Manuale utente
IOGear
IOGear Q1257-d Manuale utente
IOGear
IOGear GBU301 Manuale utente
IOGear
IOGear GWU735 Manuale utente
IOGear
IOGear GBU301 Manuale utente
IOGear
IOGear UpStream GUV302P Manuale utente
IOGear
IOGear GBP302KIT Manuale utente
IOGear
IOGear GWAVR Manuale utente
IOGear
IOGear GBU211 Manuale utente
IOGear
IOGear GUC232A Manuale utente
IOGear
IOGear GBU201 Manuale utente
IOGear
IOGear GBU421 Manuale utente
IOGear
IOGear GBS301 Manuale utente
IOGear
IOGear GVC311 Manuale utente
IOGear
IOGear GBC201 Manuale utente
IOGear
IOGear GWAVR4K Manuale utente
