iWave FD-6100 Manuale utente
1/16
www.iwavecomms.com
User Manual of FD-6100
2*2 MIMO Wireless MESH Ethernet & Full Duplex TTL Serial Data
Board
2/16
www.iwavecomms.com
Catalogue
1. Hardware ..........................................................................................................................................3
1.1. Interface ................................................................................................................................. 3
1.1.1.COMUART ..................................................................................................................... 3
1.1.2. RJ45 Port ...................................................................................................................... 6
2. Software ........................................................................................................................................... 8
2.1. WebUI Login ...........................................................................................................................8
2.1.1. Home Page Debugging Switch ..................................................................................... 9
2.1.2. Key Setting ................................................................................................................... 9
2.1.4. Wireless Setting......................................................................................................... 10
2.1.5.Network Parameter Setting ........................................................................................ 11
2.1.6.Uplink and Downlink Setting .......................................................................................11
2.1.7.VCOM .......................................................................................................................... 12
2.1.8.Debug Interface .......................................................................................................... 13
2.1.9.Device Information ..................................................................................................... 14
3. AT Commands Supported by WebUI ............................................................................................. 14
3.1.Command Set Supported by AT Debug Interface ..........................................................14
3.2.Explanation of AT Command in WebUI ......................................................................... 15
3/16
www.iwavecomms.com
1. Hardware
1.1. Interface
Note:
Using a 5V/2A adapter for power supply.
Before powering on, set the two DIP switches to the left side.
Please install the antennas firstly before powering on. Or the device will be burn out.
For short-distance test, distance between two units should be more than 10meters before
powering on. Otherwise, the equipment may be damaged.
We suggest to use IE browser (version 11) for Web login.
1.1.1.COMUART
COMUART is 2.85V voltage domain and compatible with 3V/3.3V level.
Control Data Transmission: TTL mode.
Baud rate: 115200bps, full-duplex communication
Transmission Mode: Pass-through mode
4/16
www.iwavecomms.com
The data transmitting and receiving is broadcast in the network. After successful networking, each
FD-6100 node can receive serial data.
Note: If you want to distinguish between sending, receiving and control, you need to define the
format yourself
Baud Rate: The max baud rate is 115200bps(The total rate of unidirectional receiving or
unidirectional sending)
Baud rate 115200 = 115200 (bits/second)
If there is no check digit, it should be divided by 10 to get the bytes per second:
Baud rate 115200 = 115200 (bits/second) = 11520 (bytes/second)
Then divided by 1024, it is KB per second:
Baud rate 115200 = 115200 (bits/sec) = 11.25 (KB/sec)
＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝
If there is a parity bit, it should be divided by 11 to get the number of bytes per second.
Baud rate 115200 = 115200 (bits/sec) = 10.27 (KB/sec)
How to test if the COMUART works normally?
Item
Qty
Computer
(with software sscom42 or other serial software such as putty, Serial Port Tester,
CommMonitor3.0, Serial Interface, etc.)
1
FD-6100
2
Antenna
4
TTL-USB Cable
2
Power Adapter(5V/2A)
2
TTL-USB Module
5/16
www.iwavecomms.com
Connect TTL-USB cable with FD-6100
Connect FD-6100 with Computer
Connect the antennas with FD-6100
Power the board using the adapter we supplied(DC5V/2A)
Connect the board with your computer by TTL-USB Cable.
FD-6100
USB Module
RXD
TXD
TXD
RXD
GND
GND
6/16
www.iwavecomms.com
After the driver is installed correctly, the computer will display the following COM port
information
Sending and Receiving Serial data through the COMUART
Computer Settings:
Then you can send and receive serial data via both FD-6100 COMUART
1.1.2. RJ45 Port
Item
Qty
Computer
1
7/16
www.iwavecomms.com
IP Camera
1
FD-6100
2
Antenna
4
RJ45 Cable
2
Power Adapter(5V/2A)
2
Connect FD-6100 with Computer and Camera
1. Set computer IP: 192.168.1.99/255.255.255.0
2. Set the IP Camera IP: 192.168.1.21
3. Conenct the antennas with FD-6100
4. Power FD-6100 via the adapter we supplied(DC5V/2A)
5. Connect one FD-6100 with IP Camera
6. Connect the other FD-6100 with computer
FD-6100(1) Connect with Camera FD-6100(2) Connect with Computer
7. Using the computre visit http://192.168.1.21
8. Enter into IP Camera's user name and password, then you will get the IP Camera's video on the
computer.
How to use NVR to get the camera's video
Connect IP Camera with FD-6100 as to below settings:
8/16
www.iwavecomms.com
IP
Subnet Mask
Gateway
Camera 2
170.218.2.21
255.0.0.0
170.18.15.6
(IP address of NVR)
Camera 3
170.218.2.22
255.0.0.0
170.18.15.6
(IP address of NVR)
Camera 4
170.218.2.23
255.0.0.0
170.18.15.6
(IP address of NVR)
Camera 5
170.218.2.24
255.0.0.0
170.18.15.6
(IP address of NVR)
NVR
170.18.15.6
255.0.0.0
170.18.15.1
Note: Since NVR can automatically send ARP packets, so it can be set with different subnet
network with FD-6100
2. Software
2.1. WebUI Login
WebUI interface operation is mainly to manually select the corresponding parameters or input
relevant parameters, configure the nodes, and return the configuration status displayed on the
UI interface.
The initial IP address is: http://192.168.1.12
The initial user name and password are
User name: admin123
Password: admin123
Administrator login user name and password(password and user name changing is not
supported)
Administrator username: admin123
Administrator password: admin123
After registering and changing the password, it will automatically log in and jump to the index
page.
Registration function: directly enter the user name and password, the original account will be
overwritten.
After the factory settings are restored, the account and password are restored to their initial
values.
"Login", "Registration", "Modify Password" need to configure the IE browser,
tools-options-Internet options-security settings-enable ActiveX controls and plug-ins.
Note: Administrator login does not require the above steps.
Add the local and remote IP addresses of WebUI as trusted sites.
The user name is 6-20 characters composed of letters and numbers, and the first character
must be a letter. The password is also 6-20characters.
9/16
www.iwavecomms.com
2.2.Home Page Debugging Switch
Modem switch setting: open/close
Modem Restart Setting
2.3.Key Setting
Before networking, each node need to enter into the key
2.4.Master-slave Setting
Select the AUTO and no need to modify it.
10 /16
www.iwavecomms.com
2.5. Wireless Setting
Set the frequency band
Frequency Hopping Management
Bandwidth
Indice
Altri manuali iWave Hardware per computer
iWave
iWave iW-RainboW-G40D Manuale utente
iWave
iWave FIM-1440 Manuale utente
iWave
iWave iW-RainboW-G24M Arria10 SoC FPGA SOM Manuale utente
iWave
iWave iW-RainboW-G30D Manuale utente
iWave
iWave FIP-2410 Manuale utente
iWave
iWave FIM-2450 Manuale utente
iWave
iWave iW-RainboW-G57M Manuale di installazione
iWave
iWave iW-RainboW-G37M Manuale di installazione
iWave
iWave iW-RainboW-G28M Zynq-7000 SoC SODIMM SOM Manuale di installazione
iWave
iWave FIP-2405 Manuale utente
iWave
iWave FNM-8416 Manuale utente
iWave
iWave FIM-2405 Manuale utente
iWave
iWave i.MX 8M Mini Manuale utente
iWave
iWave FDM-6600 Manuale utente
iWave
iWave FMS-8480 Manuale utente
iWave
iWave iW-RainboW-G35D Manuale di installazione
iWave
iWave FIM-2410 Manuale utente
iWave
iWave FDM-615PTM Manuale utente
iWave
iWave FPM-8416 Manuale utente
iWave
iWave i.MX6 Qseven PMIC SOM Manuale di installazione
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
