iWave FIP-2420 Manuale utente
FIP-2420 User Manual
Thank you very much for your favor of our products! This manual describes the usage of the
FIP-2420 and amis to enable you quickly grasp the use of the product.
Version 2.0.1(4)
Date 6/24/2018
IWAVE COMMUNICATIONS Co.,Ltd
3F, 19th Bldg, No.1515 Gumei Road, Minhang District, Shanghai, China
To Costumers
添加标题
This document is copyright-protected by IWAVE COMMUNICATIONS co., ltd. Laws in China and/or other
countries or areas protect the exclusive rights of the Company. The Company endeavors to achieve the
accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All the
specifications and designs are subject to change without notice due to continuous technological
development. No part of this manual may be copied, modified, translated, or distributed in any manner
without the prior written consent of the Company.
If you have any suggestions or would like to receive more information, please visit our website at:
http://www.iwavecomms.com, or email us support@iwavecomms.com.
Copyright Information
1
www.iwavecomms.com
FIP-2420 User Manual
Contents
1. Introduction................................................................................................................................... 3
2. Package List................................................................................................................................... 3
3. Precautions...................................................................................................4
4. Interfaces and Indicators .................................................................................................5
5. Operating Instructions & Steps...................................................................................................7 6.
Antenna Installation.............................................................................................................8
7. Software Operation...............................................................................................................................10
2
FIP-2420 User Manual
1. Introduction
FIP-2420 is 2.4Ghz point-to-point drone digital Ethernet data downlink radio for 18km-22km range.
It supports two way TCPIP/UDP Ethernet data and duplex serial data transmission.
2.Package List
3
FIP-2420 User Manual
3. Precautions
4
1. Please use the parts provided by IWAVE.
2. Before powering on please make sure the antennas are in good connection and not
install or remove the antennas with power on.
3. Keep the antenna on board vertically downward.
4. Antennas on board should be kept away from other radio antennas to avoid
electromagnetic noise and interference.
5. Do not disassemble or modify IWAVE FIP-2420. Any problem occur during installation,
contact IWAVEor IWAVE local branch office.
6. Keep proper distances between different radio devices to minimize the electromagnetic
interference.
7. Before use, please make sure all cables are in good connection and all components can
work properly.
8. Check the surrounding environment to ensure there is no other 2.4GHz devices or they
will cause interference with FIP-2420.
9. After powering on FIP-2420, the self-test indicator will continuously blink for 30s and
then keep bright. After the camera's video shown on the display, which means the Tx
and Rx work properly now.
10.Before use, please check the power of RX and TX. If the Rx power off, Tx on board will
lose connection.
11.Please pay attention to the angle and direction of Rx antenna during flight. When the
signal is poor or the image quality is not good, adjusting Rx antenna's tilt will improve
the signal strength and image quality.
12.The camera onboard should be fully charged to ensure normal video output.
13.If the video stuck or stopped for more than 10s which means the radio signal is too
weak or radio channel is narrowing. In this case, the aircraft need to fly back to short
the distance between TX and RX. Otherwise, the connection will be lost.
FIP-2420 User Manual
4. Interfaces and Indicators
4.1. Interfaces
5
Power Input Interface and Power Cable
Power Input: Pull - type switch
Power Connector: XT30PW-F(Female)
Power Cable: One end XT30PW(Male), the other end DC(female)
S1 Serial Port: 5P GH with lock socket(GH 1.25mm, we only use 4P)
GH 5P
Signal Definition
1
TXD
2
RXD
3
3.3V
4
GND
FIP-2420 User Manual
6
RS232 Interface
RS232: 3p GH with lock socket(GH 1.25mm)
GH 3P
Signal Definition
1
TXD
2
GND
3
RXD
RF Interface
RF: Standard SMA to connect with antenna or feeder cable
ETH: EZH 4P 1.5mm
NO
Ethernet Signal Definition
1
TX+
2
TX
3
RX+
4
RX
FIP-2420 User Manual
7
5. Operating Instructions & Steps
5.1. Connection
Make the power cable, Ethernet cable, serial cable and antenna are in good connection.
The serial port(S1) and RS232 on Tx are used to connect with the fly control system such as Pixhawk or gimbal
control
Note: RS232 and S1 can not be used simultaneously.
The serial port(S1) and RS232 on Rx are used to connect your PC with GCS via the TTL-USB cable
Ethernet Port: Ethernet port on Tx and Rx is for Ethernet data input and output and connecting with PC via LAN
cable for parameters adjusting by IFLY software.
Power Input: DC7-18V(DC12V is advised)
5.2. Power On
After checking all the connections are in good condition, turn on the camera, display, Tx and Rx. Then PWR
indicator will bright and the whole system starts work.
5.3. Indicators
When the device begin to normally work, all indicators status are described as follow:
① After power on, light 1,2,3 turn green, light 6 turns blue.
② After few seconds, light 1,2,3,6 start flashing. And light 5 keep bright in green.
③ After the starting complete. Light 1(Green), 2(Green), 3(Green), 6(blue), 4(Red) keep bright. Light 5(Green)
will fast blink.
④ When data transmission goes well, WL green light will flicker.
5.3. Boot up successfully
After successfully connection, the display will smoothly show camera's video.
Remark: In UAV application, please make the connection successfully and the video show on ground station
smoothly then fly the UAV. About how to install the antenna on UAV please refer the following description.
FIP-2420 User Manual
8
6. Antenna Installation
6.1. Multi-rotor UAV
1)Using SMA cable provided by IFLY to connect the TX SMA port with antenna.
2)The antenna needs to be mounted vertically downwards.
3)The best installation location is UAV ground bracket and the bracket need to be fiberglass material.
4)If the ground bracket is automatically retracted, the antenna can be installed in the lower part of the aircraft.
5)If the antenna is intercepted by the camera or pod or the loudspeaker, the video on RX will appear image
stuck or mosaic.
FIP-2420 User Manual
9
6.1. Fixed Wing or VTOL Drone
1. The best installation position is center of UAV tail, prominent outside the body and vertical downward.
2. The second optional mounting position is located below the wing and body joints, vertical down, as far as
possible away from the wing but near the machine abdomen, protruding below the abdomen level.
FIP-2420 User Manual
10
7. Software Operation
Note: Because Tx and Rx are working in pairs, so their parameters need be consistent, which means when
one unit parameters are changed, the other unit parameters need to be change too. Or they will lose
connection.
The following show you two ways to do the parameters settings:
(1)Connect Tx or Rx with PC separately then change their parameters one by one.
(2)When the communication between Tx and Rx are working normally, you can change the remote unit
parameters through the local unit and then change the local unit parameters.
Note: If you find the devices cannot connect with PC, firstly wait for a moment for device finishing its
running process, then try again.
Secondly, check whether the distance between Tx and Rx is too close, increase their distance and try again.
If still failure, try another Ethernet cable.
Indice
Altri manuali iWave Hardware per computer
iWave
iWave iW-RainboW-G40D Manuale utente
iWave
iWave FIM-2450 Manuale utente
iWave
iWave FIM-1440 Manuale utente
iWave
iWave FIP-2410 Manuale utente
iWave
iWave iW-RainboW-G17D Manuale utente
iWave
iWave FMS-8480 Manuale utente
iWave
iWave iW-RainboW-G28M Zynq-7000 SoC SODIMM SOM Manuale di installazione
iWave
iWave i.MX6 Qseven PMIC SOM Manuale di installazione
iWave
iWave iW-RainboW-G37M Manuale di installazione
iWave
iWave FIM-2430 Manuale utente
iWave
iWave i.MX53 Manuale di installazione
iWave
iWave iW-RainboW-G25S Manuale utente
iWave
iWave FPS-8408 Manuale utente
iWave
iWave iW-RainboW-G35D Manuale di installazione
iWave
iWave FDM-615PTM Manuale utente
iWave
iWave FNM-8416 Manuale utente
iWave
iWave iW-RainboW-G47D Manuale utente
iWave
iWave FDM-6600 Manuale utente
iWave
iWave FIM-2410 Manuale utente
iWave
iWave FIP-2405 Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
