Jakka CONTROL KIT 5 Manuale utente

JAKKA CONTROL KIT 5

USER MANUAL

- 3.1” Screen

- 6 Steps control of exhaust and supply fans

- Working of the unit in Automatic/Manual Modes

- Heating/Cooling /Fan Modes

- Room Temperature Sensor

- User Friendly Design

- Minimum ve Maximum Set Temperature Limit

- Constant HVAC-R Images

- Weekly Programming

1. ROOM THERMOSTATE

2. CONTROL PANEL

Control Panel

Control Panel run the heat recovery units by controlling supply and exhaust fans seperately and controlling electrical heater in steps.. It is also possible

to control pre and after heater, fresh air damper, bypass damper, ,heating coil, cooling coil and also EC fans

Main Features:

-Filter Alarm According to Pre-set Time counter (Pre-set Service Time)

-Pre programmed scenario selection via room thermostate

-Adjustable Mode selection (Auto Heating, Auto Cooling, , Manual

Heating , Manual Cooling, Fan Mode)

-Restart with the last paremeters in case of power shortage

-Connection to building management system (Modbus-RTU)

-Weekly Programming

3. SPECIFICATIONS

Environmental Specs

Working and Storage Temperature: 0 ... +50°C

Protection Class: EN 60529 - IP00

Electrical Specs

Control : Room Thermostate/BMS

Relay Current Capacity: Resistive 5A (Heating Contactor)

Power Supply: 230V AC

PhaseShut Down : 10A (6 Steps)

Consumption: Max 5VA, Connection 1,5mm²clips

Functional Specs

On/ Off via BMs

Embedden temperature sensor to room thermostate

Control Of;

- Duct Type Temperature Sensor

-Fresh Air Damper

-Bypass Air Damper

- External Sensor Connection (NTC 10K)

- 6 Steps Manuael or Auto Speed Selection for Exhaust

and Supply Fans seperately

Unit On/Off info

Weekly Programming

Carbondioxide/Air Quality Sensor Control (0-10V)

Proportional Valve Control

EC Fan Control

FEATURES OF ROOM THERMOSTATE:

A. ) HOW TO MAKE WEEKLY PROGRAMMING:

•Press FAN button for two (2) seconds while the unit is on.

•You will see “00” at the upper-right part of the screen, then press Mode / OK button.

•You can select starting and stopping time for each day of the week with UP and DOWN buttons on

the weekly programming screen. Go on by pressing Mode/OK button.

•To go back to previous screen and/ or to exit , use ON/OFF button.

Note1 : Unit will not work if starting time is later than stopping time.

Note2 : Unit will not work if starting time is same with stopping time.

Note3 : There will be a clock symbol on the screen, if unit works in weekly programmed hours.

Note4 : There will be a clock deleting symbol on the screen, if unit works out of weekly programmed hours.

B.) SETTING DATE AND TIME:

•Press Fan button for two (2) seconds while the unit is on.

•You will see “00” at the upper-right part of the screen, then change it to“01” by using UP and DOWN buttons,

then press Mode/OK button.

•Set hour/minute by pressing UP and DOWN buttons then go on by pressing Mode/OK

•Set day/month by pressing UP and DOWN buttons then go on by pressing Mode/OK

•Set year by pressing UP and DOWN buttons then go on by pressing Mode/OK

•Set name of the day by pressing UP and DOWN buttons then go on by pressing Mode/OK

C.) CHANGING UNIT MODE:

•The mode can be selected by pressing Mode/OK button when the unit is on.

•When the unit is at manual heating, manual cooling or fan mode, by pressing Mode/OK button fan

speed and set temperature can be adjusted. You can go to next screen by pressing Mode/OK button

•When the unit is at auto mode, passing to the next mode is possible by pressing Mode/OK button

D.) CHANGING SET TEMPERATURE:

•When unit is on and in auto mode, using UP and DOWN buttons ,set temperature number will start

blinking. Set temperature can be selected by pressing UP and DOWN buttons.

•When unit is on and in manual mode, using UP and DOWN buttons ,set temperature number will start

blinking. Set temperature can be selected by pressing UP and DOWN buttons.

E.) HOW TO ACTIVATE KEYLOCK:

•Press FAN and DOWN buttons simultaneously when the unit is on.

There will be a lock symbol on screen after 2 seconds.

All of the buttons will be locked when keylock is on.

F.) HOW TO DEACTIVATE KEYLOCK:

•Press FAN and DOWN buttons simultaneously when the unit is on.

•Lock symbol on the screen will be deleted after 2 seconds. Then press any button.

•All buttons will be functional again.

G.) HOW TO RESET ALARM CODE:

•If “Err 0001” alarm (or any other alarm) code blinking on screen

•Press FAN and UP buttons simultaneously

H.) HOW TO RESET FILTER DIRTINESS COUNTER:

•When you got “0001” warning on the screen ,

•You can reset it by pressing FAN and Mode/OK buttons simultaneously.

Note: You can change filter dirtines alarm period on Parameter 177 . You can follow the remaining time from

Parameter 115 .

I.) ENTERING TO SERVICE MENU:

To Enter:

•Press UP and DOWN buttons simultaneously

•Enter service menu password by using UP and DOWN and press Mode/OK.

Note: The Service menu password is“58”

•Then go to Parameter you want to change by using UP and DOWN buttons then press Mode/OK button

•Change the parameter by using UP and DOWN buttons then press Mode/OK button.

•Get out of menu by pressing ON/OFF button

Caution : All the changes on the service menu should be done by authorized personnel.

The damage and problems causing by unauthorized changes on the service menu will be on

user’s responsibility.

J.) SELECTING TEMPERATURE CONTROL POINT

There are 4 options that unit can check the temperature;

-Room thermostate

-Return Air

-Supply Air

-Outside Air

To select one of these;

•Press UP and DOWN buttons simultaneously

•Enter service menu password by using UP and DOWN and press Mode/OK.

•

Note: Service menu password is “58”

•Then go to Parameter ‘’118’’ by using UP and DOWN buttons then press Mode/OK button

•Change the parameter by using UP and DOWN buttons then press Mode/OK button.

Parameter 118 could be one of below numbers

0-Room thermostate

1-Return Air

2-Supply Air

3-Outside Air

•Get out of menu by pressing ON/OFF button

Note: Selected sensor should be connected to the card . If not, there will be “- -“symbol on the screen.

K. SETTING FAN STEP PARAMETERS

STEPKADEME AYARI

Each 6 steps of supply and exhaust fans could be set seperately..

To set step value of the fans

•When the unit is connected to power supply , press UP and DOWN buttons simultaneously

•Enter service menu password by using UP and DOWN and press Mode/OK.

•Go to step needed to be changed by using UP and DOWN and press Mode/OK.

•Change the value according to table below by using UP and DOWN and press Mode/OK.

•Check out from the menu by using ON/OFF button

Fan Step Parameters

130

Exhaust Fan 0. Step Value

0-100

131

Exhaust Fan 1. Step Value

132

Exhaust Fan 2. Step Value

133

Exhaust Fan 3. Step Value

134

Exhaust Fan 4. Step Value

135

Exhaust Fan 5. Step Value

136

Exhaust Fan 6. Step Value

137

Supply Fan 0. Step Value

0-100

138

Supply Fan 1. Step Value

139

Supply Fan 2. Step Value

140

Supply Fan 3. Step Value

141

Supply Fan 4. Step Value

142

Supply Fan 5. Step Value

143

Supply Fan 6. Step Value

L. SETTING FRESH AIR DAMPER OPENING TIME

•When the unit is connected to power supply , press UP and DOWN buttons simultaneously

•Enter service menu password “58”by using UP and DOWN and press Mode/OK.

•Go to parameter ‘’199’’ by using UP and DOWN and press Mode/OK.

•Change the value by using UP and DOWN and press Mode/OK.

•Check out from the menu by using ON/OFF button

Note: Parameter 119 values as seconds

Caution;If the fans run before damper opens, fan motors could be broken..

M. ADDING PRE-HEATER

You can add preheater by configuring the below parameters ;

•When the unit is connected to power supply , press UP and DOWN buttons simultaneously

•Enter service menu password “58”by using UP and DOWN and press Mode/OK.

•Go and change to below parameter by using UP and DOWN and press Mode/OK.

•Change the value by using UP and DOWN and press Mode/OK.

•Check out from the menu by using ON/OFF button

PARAMETER

SET VALUE

EXPLANATION

423

After Heater Relay Selection

152

Hysterisis(1C=10)

154

PreHetaer Step Quantity

Altri manuali per CONTROL KIT 5

Indice

Altri manuali Jakka Unità di controllo

Jakka

Jakka CONTROL KIT 5 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente