Johnson 40-6164 Manuale utente
©2015 Johnson Level & Tool - Rev. 2 1
Magnetic Torpedo Laser Le el
Model No. 40-6164
Instruction Manual
Congratulations on your choice of this Magnetic Torpedo Laser Level.
We suggest you read this instruction manual thoroughly before using
the instrument. Save this instruction manual for future use.
This tool emits one laser beam that is selectable as a point, vertical
line, or horizontal line. Visibility of the beam depends upon lighting
conditions in the work area.
This is a Class IIIa laser tool and is manufactured to comply
with CFR 21, parts 1040.10 and 1040.11 as well as international
safety rule IEC 285.
8726H-All_Manuals 1/5/15 8:18 AM Page 1
2©2015 Johnson Level & Tool - Rev. 2
Table of Contents
1. Kit Contents
2. Features and Functions
3. Safety Instructions
4. Location/Content
of Warning Labels
5. Location of Parts/Components
6. Operating Instructions
7. Using the Product
8. Self-Check & Fine Calibration
9. Technical Specifications
10 Application Demonstrations
11. Care and Handling
12. Product Warranty
13. Warranty Registration
14. Accessories
15. Trouble Shooting
1. Kit Contents
Model No. 40-6164 Qty.
Magnetic Torpedo Laser Level 1
“AAA” Alkaline Batteries 2
Instruction Manual with Warranty Card 1
Soft-sided Pouch 1
2. Features and Functions
• Aluminum frame for superior accuracy and durability
• Four vials read plumb, level, 45º and cross check
• Built-in rotating head swivels to project laser dot, horizontal or
vertical line
• Magnetic bottom allows unit to be attached to metal
• Available for operation by mounting on tripod
8726H-All_Manuals 1/5/15 8:18 AM Page 2
©2015 Johnson Level & Tool - Rev. 2 3
3. Safety Instructions
Please read and understand all of the following instructions, prior
to using this tool. Failure to do so, may void the warranty.
DANGER!
Class IIIa Laser Product
Max. Power Output: ≤5mW
Wavelength: 640-660nm
THIS T L EMITS LASER RADIATI N.
D N T STARE INT BEAM.
AV ID DIRECT EYE EXP SURE.
ATTENTION IMPORTANT
• Read all instructions prior to operating this laser tool. Do not remove any labels from tool.
• Do not stare directly at the laser beam.
• Do not project the laser beam directly into the eyes of others.
• Do not set up laser tool at eye level or operate the tool near a reflective surface as
the laser beam could be projected into your eyes or into the eyes of others.
• Do not place the laser tool in a manner that may cause someone to unintentionally
look into the laser beam. Serious eye injury may result.
• Do not operate the tool in explosive environments, i.e. in the presence of gases or
flammable liquids.
• Keep the laser tool out of the reach of children and other untrained persons.
• Do not attempt to view the laser beam through optical tools such as telescopes as
serious eye injury may result.
• Always turn the laser tool off when not in use or left unattended for a period of time.
• Remove the batteries when storing the tool for an extended time (more than 3 months)
to avoid damage to the tool should the batteries deteriorate.
• Do not attempt to repair or disassemble the laser tool. If unqualified persons attempt
to repair this tool, warranty will be void.
• Use only original ohnson®parts and accessories purchased from your ohnson®
authorized dealer. Use of non- ohnson®parts and accessories will void warranty.
8726H-All_Manuals 1/5/15 8:18 AM Page 3
4©2010 Johnson Level & Tool - Rev. 1
4. Location/Content of Warning Labels
8726H-All_Manuals 1/5/15 8:18 AM Page 4
©2015 Johnson Level & Tool - Rev. 2 5
5. Location of Part/Components
Bubble Adjusting Screw
Power
Button
45° Vial
Mode
Conversion
Head
Rotating Head
Horizontal VialBattery Door
Vertical Vial
Magnets
1/4" Screw
Thread hole
Magnets
Cross Check Vial
8726H-All_Manuals 1/5/15 8:18 AM Page 5
6©2015 Johnson Level & Tool - Rev. 2
IMP RTANT: It is the responsibility of the user to verify the
calibration of the instrument before each use.
6. perating Instructions
Battery Installation
Remove battery door by rotating it counter-
clockwise, put in two alkaline “AAA”
batteries according to the illustrated polarity
requirements, then install the battery door by
rotating it clockwise.
Note: Used (discharged) batteries are hazardous waste and should be
disposed of properly.
7. Using the Product
Power n/ ff
1. Press power switch to project laser line or point.
2. Press power switch again to shut off laser output.
Switch Between Laser Point
and Laser Line
1. Turn the mode conversion knob to switch
between laser line and laser point. Rotating
the lens up or down converts laser from a dot
to a line, or line to a dot. Rotating the lens
counter-clockwise, while in line
mode, rotates line from horizontal to vertical.
Battery
Battery Door
Power Switch
Rotate to switch
between point
and line
8726H-All_Manuals 1/5/15 8:18 AM Page 6
©2015 Johnson Level & Tool - Rev. 2 7
Note: The rotating head can be turned
only in the direction indicated by
arrowhead sign.
Rotating Direction
Indication
Lens
Rotatable Line Status
8. Self-Check & Fine Calibration
IMP RTANT: It is the responsibility of the user to verify the
calibration of the instrument before each use.
Checking Vials
Start by making sure that the vials are accurate. This is done by
placing the level on a flat surface and noting the position of the vial.
Rotate the level by 180 degrees (on the same gauging edge) and
observe that the bubble is in the same position.
8726H-All_Manuals 1/5/15 8:18 AM Page 7
8©2015 Johnson Level & Tool - Rev. 2
Calibrating Vials
To access the calibration screws remove the stickers located to the
right and left of the vial at the top of the unit. First, adjust the
calibration screws to move the bubble back to center taking out half
of the error in the vial. Rotate the level 180° on the same gauging
edge and move the bubble to center. Repeat this process until the
error is entirely removed and the bubble stays in the center. Plumb
vial, cross check vial and 45° vial cannot be calibrated.
Checking Laser
Once the vials are accurate, laser accuracy can be verified (near tar-
get, far target method). Start by placing the unit on a flat surface and
aim the laser at a stationary target. Position the unit/target at close
range and note a reference point on the target. As the unit is moved
away from the target, such that alignment of the laser to the target is
fixed, and the only variable is distance, the accuracy of the laser can
be verified/calibrated.
Calibrating Laser
There are set screws on the side and bottom of the unit that provide
calibration for the laser. One screw will need to be loosened before
the opposite screw can be tightened.
For vertical calibration, use underside screws, tightening the front
screw to adjust up and tighten the rear to adjust down.
For horizontal calibration, use two screws on either side of the unit.
Tighten the right screw to adjust right. Tighten the left screw to
adjust left.
8726H-All_Manuals 1/5/15 8:18 AM Page 8
©2015 Johnson Level & Tool - Rev. 2 9
9. Technical Specifications
Laser Wavelength 650nm ± 10
Laser Classification Class IIIa
Maximum Power Output ≤5mW
Accuracy ± 1/8"/50 ft. (±1mm/5m)
Interior Range Up to 100 ft. (30m)
depending upon light conditions
Power Supply 2 “AAA” alkaline batteries
Battery Life Approx. 30 hours continuous use
Dimensions 7-1/2" x 2-1/8" x 3/4"
(190 x 55 x 20mm)
Weight 0.7 lbs. (0.3 Kg)
Working Temperature 14°F to 113°F (-10°C to +45°C)
Center Screw Thread 1/4" – 20
8726H-All_Manuals 1/5/15 8:18 AM Page 9
10 ©2015 Johnson Level & Tool - Rev. 2
10. Application Demonstrations
Projects one laser point
Projects one horizontal laser line
Projects one vertical laser line
8726H-All_Manuals 1/5/15 8:18 AM Page 10
Indice
Lingue:
Altri manuali Johnson Livello laser
Johnson
Johnson 40-6692 Manuale utente
Johnson
Johnson 40-0612 Manuale utente
Johnson
Johnson 40-6060 Manuale utente
Johnson
Johnson 5700-0800LZR Manuale utente
Johnson
Johnson JLX LEVEL UP 40-6681 Manuale utente
Johnson
Johnson 40-6174 Manuale utente
Johnson
Johnson 40-6515 Manuale utente
Johnson
Johnson 40-6250 Manuale utente
Johnson
Johnson 1876-2400 Manuale utente
Johnson
Johnson 40-6650 Manuale utente
Johnson
Johnson 40-6060 Manuale utente
Johnson
Johnson 40-6646 Manuale utente
Johnson
Johnson 40-6690 Manuale utente
Johnson
Johnson 40-6936 Manuale utente
Johnson
Johnson 40-6602 Manuale utente
Johnson
Johnson 40-6636 Manuale utente
Johnson
Johnson 40-6926 Manuale utente
Johnson
Johnson 40-6685 Manuale utente
Johnson
Johnson 40-6647 Manuale utente
Johnson
Johnson 40-6551 Manuale utente
