Jolly Mec Control Display Manuale utente

SM096 EN REV03 2016_05

CONTROL

DISPLAY

USER MANUAL

To be kept by the purchaser

Control display for water heating products

Dear Customer,

thank you for having chosen to heat and save with a Jolly Mec product. Please carefully read and keep this sheet

before using the equipment.

The manual provides information and suggestions necessary for correct product use. Knowing and observing these

instructions will allow you to fully and safely enjoy the potential your equipment can offer you.

SM096 EN REV03 2016_05 3

ENGLISH

TABLE OF CONTENTS

CHAP.01 PREMISES...................................................................................................................................4

01.1 WARNINGS .................................................................................................................................................. 4

01.2 SYMBOLOGY............................................................................................................................................... 4

CHAP.02 USER INTERFACE...................................................................................................................... 5

02.1 CONTROL DISPLAY DESCRIPTION........................................................................................................... 5

02.2 KEY FUNCTIONS......................................................................................................................................... 5

02.3 ICON MEANINGS......................................................................................................................................... 6

CAP.03 OPERATING MODE ....................................................................................................................6

03.1 APPLIANCE OPERATIONS ......................................................................................................................... 6

03.2 MAIN STATUS MESSAGE MEANINGS ....................................................................................................... 7

03.3 MAIN SETTINGS.......................................................................................................................................... 8

CHAP.04 USER MENU................................................................................................................................9

04.1 FUNCTIONS................................................................................................................................................. 9

04.2 STRUCTURE.............................................................................................................................................. 10

CHAP.05 FAULT DIAGNOSIS AND TROUBLESHOOTING ....................................................................23

05.1 ALARM MESSAGES .................................................................................................................................. 23

CHAP.01 PREMISES

01.1 WARNINGS

• Werecommendyoucarefullyreadandfollowtheinstructionsinthismanualforcorrectuse.

• Itshouldbekeptwithcareandattentivelyconsultedsinceallthewarningsprovideimportantsafetyinstructions.

• Incorrectusecouldcausedamageandinjurytopeople,animalsorproperty,forwhichthemanufacturercannotnotbeheldliable.

• Theappliancemustbeusedonlyforitsintendedpurpose.Anyotheruseisdeemedimproperandthereforedangerous.

• Themanufacturerdeclinesanycontractualornon-contractualliabilityfordamagescausedbyerrorsininstallationoruseofthe

applianceorfailuretofollowtheinstructionscontainedinthismanual.

• AllrightsonthereproductionofthistechnicalmanualareownedbyJollyMecCaminettiS.p.A.

• Thedescriptionsandillustrationsprovidedinthefollowingpublicationarenotbinding.

• JollyMecCaminettiS.p.Areservestherighttomakeanymodicationsthatmaybedeemedappropriate.

• ThismanualcannotbegiventothirdpartiesforperusalwithoutthewrittenpermissionofJollyMecCaminettiS.p.A.

• Donotmakeanyunauthorisedmodicationtotheappliance.Anyunauthorisedmodicationwillautomaticallyinvalidatethewarranty

andreleasethemanufacturefromallliability.

• Useonlyoriginalsparepartsrecommendedbythemanufacturer.Originalsparepartsareavailablethroughretailers,specialised

TecnicalServiceCenters,ordirectlyattheheadofceofJollyMecCaminettiS.p.A.

01.2 SYMBOLOGY

In this manual, points of considerable importance are marked with the following symbology:

INSTRUCTION: Instructions regarding the correct use of the appliance.

WARNING: This point is particularly important.

ENGLISH

CHAP.02 USER INTERFACE

02.1 CONTROL DISPLAY DESCRIPTION

The control display lets you communicate with the control unit. The keys are used to transmit commands to the control unit while the

display informs the user on stove operating status. Programming mode displays the various settings that can be edited using the keys.

02.2 KEY FUNCTIONS

Key Description Mode Action

1Temperature selection

QUICK ACCESS Rapid access to adjust Set ambient temperature

Increase

EDIT VALUE Increases the selected setting value

Chronothermostat

ACTIVATE CRONO Pressed together with button 2 activates the Timer function.

2Temperature selection

QUICK ACCESS Rapid access to adjust Set Water temperature in the appliance

Decrease

EDIT VALUE Decreases the selected setting value

Chronothermostat

ACTIVATE CRONO Pressed together with button 2 activates the Timer function

3On/Off - Esc - REsEt

OFF Turns on

WORK Turns off

ALARM Resets the alarm

MENU Returns to the previous level

4Access Menu/Conrm

OFF Opens the menu

WORK Opens the menu

MENU Conrms changed settings and moves to the next Menu page

5Output selection

QUICK ACCESS Rapid access to set the power

Increase

EDIT VALUE Increases output value

Decrease page

MENU Change page within the Menu

6Temperature selection

QUICK ACCESS Rapid inlet to regulate Set Temperature Puffer and Boiler

Decrease

EDIT VALUE Decreases output value

Increase page

MENU Changes page within the menu

Display

IR receiver

Component reference icons

02.3 ICON MEANINGS

A segment may or may not be found next to each icon on the display to indicate whether or not the relevant component and/or function

is enabled. The functions or components associated with the various icons are:

The image below depicts an example of a display screen which indicates that the chronothermostat function is running and the auger

gear motor and electrical resistance are running.

The rst row on the display shows the current time, the second row shows, from the left, room temperature and water temperature, whilst

the third and fourth rows show, respectively, the device status and operating output.

Room probe request Auger gear motor

Chronothermostat Fume fan

Electrical resistance Water circulator

Auxiliary circulator Alarm

CAP.03 OPERATING MODE

03.1 APPLIANCE OPERATIONS

When the appliance is OFF, press and hold down Key 3 on the display for several seconds to turn it on. Next, the start-up message will

appear on the display indicating that the switch-on procedure is made up of various phases dened in technical parameter settings and

to be set by a specialised Technical Service Center. After the normal switch-on time, the device normally reaches the RUNNING condition

at the set output unless fume temperature reaches the minimum admitted value and the relevant alarm message is displayed. In normal

conditions the device maintains work status, running the BASKET CLEANING mode at set intervals until the set room temperature is

reached (or other temperature according to the probe or set system conguration). Afterwards, it switches to ECO MODULAT- mode

running at reduced regime. If STAND-BY mode is on, the device turns off after a period of time in economy mode or after this condition

led to a certain increase in the reference temperature. The length of this period and the temperature increase can be set in MENU 5 –

STAND BY. In STAND-BY mode, the stove automatically turns back on when the reference temperature drops under the set value. To

manually turn off the stove, simply press and hold down Key 3 for several seconds. Next, FINAL CLEANING is run.

ENGLISH

03.2 MAIN STATUS MESSAGE MEANINGS

During normal operations, the screen displays the time, room temperature, water temperature and a message that indicates device status

when the message is displayed. An illustration of the main display screen appears below.

The main messages that can appear on the display and their meanings are summarised in the following table:

MESS-

TEXT Description

OFF

Message displayed when the appliance is off. It can be switched on in manual mode, using a

GPRS system or chronothermostat settings.

INITIAL

ventil-

Message displayed during the initial ventilation phase during the rst start-up phase.

PRELOAD

PELLET

Message displayed during the initial pellet preload phase.

WAIT

FLAME

Message is displayed during the stand-by time before the pellets are ignited. The fumes

temperature must reach a set value for the device to be considered ON.

fLAME

Message displayed when the device is on. This message remains on the screen for a short

period of time while the ame stabilises and pellet ignition in the brazier is completed.

RUNNING

Message displayed during device operations in work mode, meaning until the temperature read by

the room probe or water probe reaches the set value.

The number indicated next to the letter P indicates the output level at which the device is running.

If the number ashes, the device is increasing or decreasing output.

BASKET

CLEANING

Message displayed during the clean brazier automatic cycle that is run at regular intervals

while the stove is running. A forced ventilation cycle of the fumes extractor removes any excess

unburned materials from the brazier.

final

CLEANING

Message displayed during the shutdown phase.

eco

modulaT-

Message displayed when the room and/or water temperature value is reached. The appliance

automatically switches to economy mode.

STAND-BY

The previous screen is alternated when, after a period of running in ECONOMY mode, the

device enters STAND-BY and shutdown conditions are met.

OFF

WAITING

Message displayed when, during the start phase, the switch off button is pressed. Device

shutdown during the switch-on phase is not permitted. Therefore, the command is saved and

will be run at the end of the stabilisation phase.

WAITING

COOLING

Message displayed during the shutdown phase for STAND-BY mode

WAIT

RESTART

Message displayed when, during the shutdown phase, the switch on button is pressed. Device

start during the shutdown phase is not permitted. Therefore, the command is saved and run

when the fume temperature drops under 80°C.

STAND-BY The device is OFF, waiting to be automatically restarted by a probe signal that requests heat.

The device is not completely switched off in STAND-BY status, but is OFF waiting to restart.

ORDINARY

SERVICE

The device has reached the periodic servicing warning signal, to be reset with the heating stove

OFF by pressing Key 3 on the home page.

Output settings

03.3 MAIN SETTINGS

Use the specic keys on the control display to directly access from the main page the room, stove and, according to the adopted system

conguration, the puffer and/or boiler output and temperature settings pages.

Temperature settings

To change the operating output, press Key 5on the main page to immediately open the

screen where you can use the Keys 5 or 6 to select from the ve settable output settings.

After selecting the required output level, press Key 3to return to the main page.

To change the required temperatures, press Key 1,2 or 6 on the main page to immediately open the relevant section. The set values

can be changed using keys 1 and 2 in each screen. If diagram 7 is set, press key 6 once to access the set Puffer settings, press key 6

twice to access the set Boiler settings.

After selecting the required output level, press Key 3to return to the main page.

Key 1

For all Conguration

Key 2

For all Conguration

Key 6

With Conguration 5 or 7 set.

The second row represents the temperature read by

the probe.

Key 6

With Conguration 6 or 7 set.

The second row represents the temperature read by

the probe.

ENGLISH

CHAP.04 USER MENU

04.1 FUNCTIONS

The display is divided into menus and sub-menus that can be scrolled using the control display keys. In short, main menus and their

functions are:

MENU Description

1 - SET CLOCK

Lets you set the current date and time, required for correct chronothermostat operations

2 - SET CHRONO

Lets you turn the chronothermostat and its programs on or off. The delay programme is enabled on

crono page, that independently from the crono, can be used to delay start-ups and switch-offs.

3 - SET LANGUAGE

Lets you set the menu language

4 - SET PROBE

Lets you set the type of room probe to be used.

• Set THERMOSTAT probe type to use a thermostat to control the appliance. If a retail thermostat

is used, the device must be used with clean contacts to the appliance. The Jolly Mec thermostat

module is also considered a thermostat. Therefore, if an original Jolly Mec device is used, set

THERMOSTAT as probe type.

• Set PROBE type to use the probe installed on the stove or a remote same type of probe in another

room. In the latter case, the probe installed on the stove must be disconnected from the electronic

card (to be done by a specialised Technical Service Center).

5 - SET STAND-BY

STAND-BY mode lets you turn off the appliance when room or water temperature requests, according

to the set conguration, are met. In STAND-BY (display message) the appliance is awaiting room or

accumulation tank thermostat requests to restart a switch-on cycle. The delay time delays shutdown

from the moment when the requests are met. If PROBE type was set in MENU 4, the appliance will

only shutdown after running in ECONOMY mode for a period of time equal to DELAY OFF time after

requests are met while if THERMOSTAT type is set, the appliance will run in ECONOMY mode for twice

as long as the set DELAY OFF time.

6 - SET DISPLAY

Allows you to change the device acoustic signals settings and delay the switch-off of the back-lighting.

7 - PELLET LOAD

Lets you start manual pellet load. It can be used after the completely empty tank was lled with fuel,

to ll the burner.

8 - STATE STOVE

Allows you to check the actual operating status scrolling through the various pages using Keys 5 or 6.

9 - TECHNIC SETTINGS

This menu contains the appliance settingspages that only the specialised Technical Service Center can

access using a specic password.

A - REGULATE SETTING

Lets you change pellet loading and fume exhaust settings

B - COUNTER MEMORY

Lets you read some data stored in the control unit memory

C - SEASON

Lets you set either winter or summer operating mode

04.2 STRUCTURE

To open the various menus, press Key 4when the main page is displayed on the remote control. To scroll the various menu pages, use

Keys 5and 6.

M1-001 DAY

To select the current day of the week, use Keys 1and

2and press Key 4to set the displayed value and move

to the next page.

M1-002 HOUR CLOCK

To set the hour, use Keys 1and 2and press Key 4to set

the displayed value and move to the next page.

M1-003 MINUTES CLOCK

To set the minutes, use Keys 1and 2and press Key 4

to set the displayed value and move to the next page.

M1-004 DAY CLOCK

To select the current day, use Keys 1and 2and press

Key 4 to set the displayed value and move to the next

page.

M1-005 MONTH CLOCK

To select the current month, use Keys 1and 2 and press

Key 4 to set the displayed value and move to the next

page.

M1-006 YEAR CLOCK

To select the current year, use Keys 1and 2 and press

Key 4 to set the displayed value and move to the next

page.

When nished, the message DONE will be displayed

to conrm correct data entry. Next, the level page

automatically returns to the Menu Page.

MENU 1 - SET CLOCK

4 5

Indice

Altri manuali Jolly Mec Unità di controllo

Jolly Mec

Jolly Mec QUA/ARIA/6 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente