Kauber RC-02 Manuale utente
Radio Control RC-02 Installation Manual
RC-02 module was special desined for every kind of screen to make it wireless.
Works with iRemote and Classic Remote. You just plug one wire to the 2 0V socket and second to
the screen and it is ready.
Description:
The control is done via remote control or buttons on the module. When you bring up the voltage
plug 2 0V AC power to the module, LED is indicating that the module is in standby mode and
ready for operation.
The remote controller and the module are equipped with three buttons:
- UP (rolling up screen/lift)
- STOP
- DOWN (rolling down screen/lift)
After pressing the UP or DOWN button on the remote control/control module - the LED starts
blinking and on the cable supplying screen/lift appears 2 0V AC voltage (causing rolling up/rolling
down of the screen/lift).
After pressing the STOP button the LED lights permanently and on the power cord of
screen/lift disappears 2 0V AC voltage (causing stopping the screen).
Installation:
The installation of Radio Control RC-02 module starts with connecting the cable which is
responsible for steering the engine of screen/lift.
According to the colours of wires connect cables to the engine in the following order:
- BLACK cable (PHASE L1) – rolling down screen/lift
- BROWN cable (PHASE L2) – rolling up screen/lift
- BLUE cable (N) – zero cable (neutral)
- GREEN/YELLOW cable (PE) - ground
Then connect the module to 2 0V AC power accoring to the following cable order:
–BROWN cable – phase cable L
–BLUE cable – zero/neutral cable N
–GREEN/YELLOW cable – ground cable PE
WARNING!
Before starting the device please make sure that all cables were connected according to the
installation manual.
The connecting of the module should be done by a person with appropriate electrical powers.
Adding/Progra ing of re ote control:
RC-02 is ready to work with two kinds of remote controller – iClassic and iRemote (available
separately). There can be programmed up to 20 remote controllers to one module.
CLASSIC iREMOTE
To add a remote control to RC-02 unit please follow the instructions below:
1) Turn on the power module
2) Press “the Programming” on the module. Green LED starts flashing.
) While LED is flashing press the STOP button on the module (not on the remote controler!) STOP
(middle button). The green LED starts to light up permanently.
4) Press the "UP" on the remote controler. Green LED flashes to confirm programming of remote
controler to the module, simultaneously leaving the programming mode.
Too long pressing of the "UP" button during programming may also cause rolling up/ rolling down
of screen/lift. In this case please push "STOP" on remote control.
To remove the remote control of a RC-02 module please follow:
1) Perform steps 1- as for adding a remote control (see an instruction above)
2) Press the "DOWN" on the remote controler. The green LED will flash confirming the
disappearance of the remote control. of the module, simultaneously leaving the programming mode.
Changing directions:
In the module, we can replace the directions of work screen / lift without re-wiring.
To do this simply move the button "swap lines” on the module .
Specifications:
- supply voltage – 2 0V AC
- maximum power load - 10A
- power consumption in idle mode - 20mA
- power consumption during operation - 50mA
- time between changing direction - 1s
Thank you for choosing KAUBER Radio Control Module
We encourage you to purchase other devices from KAUBER
Manufactured by 1 /08/2005.
Do not throw used electrical and electronic devices together with domestic waste because of the presence of items of
environmentally hazardous substances. These devices should convey to the rebound point for recycling.
Information about rebound points is available in local government or commercial outlets.
Indice
Altri manuali Kauber Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
