Keithley 1600A Manuale utente

Model 1600A High Voltage Probe

User’s Guide

PA-148 Rev. A / 09-05

Keithley Instruments, Inc.

28775 Aurora Road

Cleveland, Ohio 44139

(440) 248-0400

www.keithley.com

INC CROUND I ND MUSI DI

COMMCND ID SANIN

WARNING

This high voltage probe is designed to prevent accidental shock to

the operator when properly used. This operating note must be read

and fully understood prior to using the probe.

Speciﬁcations

Input resistance: Approx. 1000m

Ω

Division ratio: 1000:1

Maximum working voltage: 40KV DC or Peak AC, 28KV RMS AC

Accuracy: DC volts: ±1%(1KV to 20KV), ±2%(20KV to 40KV)

AC volts: Typically 5% at 60Hz

Temperature Coefﬁcient: Less than 200ppm/ºC

Operating temperature: 0ºC to +50ºC

Storage temperature: -20ºC to -70ºC

Cable length: 1 meter

Safety precautions

This high voltage probe must only be used by personnel who are trained, experienced, or otherwise

qualiﬁed to recognize hazardous situations and who are trained in the safety precautions that are

necessary to avoid possible injury when using such a device.

Do not work alone when working with high voltage circuits.

For your own safety, inspect the probes for cracks and frayed or broken leads before each use. If defects

are noted, DO NOT use the probe.

Hands, shoes, ﬂoor, and work bench must be dry. Avoid making measurements under humid, damp, or

other environmental conditions that might affect the safety of the measurement situation.

If possible, always turn the high voltage source off before connecting or disconnecting the probe.

The probe body should be kept clean and free of any conductive contamination. Refer to the section on

cleaning.

Operation

1. Connect the plugs to the volts (HI) and corn (LO) input terminals of your voltmeter.

2. Select the desired voltmeter function and range: do not use autoranging.

3. Whenever possible, turn the high voltage source off before making any connections.

4. Connect the divider probe common lead (alligator clip) to a good earth ground or reliable chassis

ground.

WARNING

Do not attempt to take measurements from sources where the

chassis or return lead is not grounded.

WARNING

This ground connection is critical to the safe operation of the probe.

Failure to make this connection when making high voltage

measurements may result in personal injury or damage to the probe

or voltmeter. This connection must always be made BEFORE the

probe tip comes into contact with the high voltage and must not be

removed until after the probe tip has been removed from the high

voltage source.

WARNING

Do not connect the ground clip lead to the high voltage source or the

probe lip to ground for any reason.

WARNING

Before turning the high voltage on, make sure that no part of your

body is in contact with the device under test.

5. Measure the voltage remembering that the voltage being measured is 1000 times greater then the

voltmeter reading.

6. Turn the high voltage off.

7. Disconnect the probe tip from the high voltage source BEFORE removing the ground clip lead.

Cleaning

Clean only the exterior probe body and cables. Use a soft cotton cloth lightly moistened with a mild

solution of detergent and water. Do not allow any portion of the probe to submerge at any time.

Dry the probe thoroughly before attempting to make voltage measurement.

Do not subject the probe to solvent fumes as these can cause deterioration of the probe body and cables.

Indice

Altri manuali Keithley Apparecchiature di prova

Keithley

Keithley 2520 Manuale utente

Keithley

Keithley 261 Manuale utente

Keithley

Keithley 7012-S Manuale utente

Keithley

Keithley System SourceMeter 2602B Manuale utente

Keithley

Keithley Interactive SourceMeter 2450 Istruzioni di installazione e manutenzione

Keithley

Keithley 263 Manuale utente

Keithley

Keithley 8009 Manuale utente

Keithley

Keithley 8010 Manuale utente

Keithley

Keithley SourceMeter 2425 Manuale utente

Keithley

Keithley S530 Manuale utente

Keithley

Keithley 263 Manuale utente

Keithley

Keithley S530 Manuale utente

Keithley

Keithley Interactive SourceMeter 2450 Manuale utente

Keithley

Keithley 2520INT Manuale utente

Keithley

Keithley S530 Manuale utente

Keithley

Keithley 7158 Manuale utente

Keithley

Keithley S530 Manuale utente

Keithley

Keithley 8009 Manuale utente

Keithley

Keithley 6521 Manuale utente

Keithley

Keithley 7071 Manuale utente

Keithley

Keithley 2657A Manuale utente

Keithley

Keithley 2520 Manuale utente

Keithley

Keithley S500 Manuale utente

Keithley

Keithley 3330 Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente