Kichler Lighting Windham Manuale utente
1
1. SAFETY RULES
1. To reduce the risk of electric shock, insure
electricity has been turned off at the circuit
breaker or fuse box before beginning.
2. All wiring must be in accordance with the
National Electrical Code and local electrical
codes. Electrical installation should be
performed by a qualified licensed
electrician.
3. WARNING: Suitable for use with solid-
state speed controls.
4. WARNING: To reduce the risk of personal
injury, use only the two steel screws (and
lock washers) provided with the outlet box
for mounting to the outlet box. Most outlet
boxes commonly used for the support of
lighting fixtures are not acceptable for fan
support and may need to be replaced,
consult a qualified electrician if in doubt.
5. The outlet box and support structure must
be securely mounted and capable of
reliably supporting a minimum of 50
pounds. Use only CUL Listed outlet boxes
marked "FOR FAN SUPPORT".
6. The fan must be mounted with a minimum
of 7 feet clearance from the trailing edge of
the blades to the floor.
7. To operate the reverse function on this fan,
press the reverse button while the fan is
running.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT FAN TO
OUTLET BOX MARKED "ACCEPTABLE FOR FAN
SUPPORT".
8. WARNING: Use only with light kit marked
"Suitable for Use in Damp Locations".
9. Avoid placing objects in the path of the
blades.
10. To avoid personal injury or damage to the
fan and other items, be cautious when
working around or cleaning the fan.
11. Do not use water or detergents when
cleaning the fan or fan blades. A dry dust
cloth or lightly dampened cloth will be
suitable for most cleaning.
12. After marking electrical connections,
spliced conductors should be turned
upward and pushed carefully up into outlet
box. The wires should be spread apart with
the grounded conductor and the
equipment-grounding conductor on one
side of the outlet box.
13. Electrical diagrams are reference only.
Light kits that are not packed with the fan
must be CUL Listed and marked suitable
for use with the model fan you are
installing. Switches must be CUL General
Use Switches. Refer to the Instructions
packaged with the light kits and switches
for proper assembly.
WARNING
TO REDUCE THE RISK OF PERSONAL INJURY,
DO NOT BEND THE BLADE BRACKETS (ALSO
REFERRED TO AS FLANGES) DURING
ASSEMBLY OR AFTER INSTALLATION. DO NOT
INSERT OBJECTS IN THE PATH OF THE BLADES.
2
3. PACKAGE CONTENTS
Unpack your fan and check the contents. You
should have the following items:
a. Fan blades (5)
b. Mounting plate
c. Fan motor assembly
d. Motor housing
e. Set of blades brackets (5)
f. Mounting plate
g. Light kit
h. Glass shade
i. Part bag contents
1) Mounting hardware :
wood screws (2), flat washers (2),
star washers (2), wire nuts (3)
2) Blade attachment hardware:
screws (17), washers (17),
rubber washers (17)
3) Blade brackets hardware:
screws (10)
4) Safety cable hardware:
wood screw, lock washer, flat washer
5) Close mount hardware:
screw with lock washers (3)
6) Pull chain and fobs (2)
7) Balance Kit
Philips screw driver
Blade screw driver
11 mm wrench
Step ladder
Wire cutters
2. TOOLS AND MATERIALS REQUIRED
a
b
c
d
e
f
g
h
i
WindhamTM
3
4. MOUNTING OPTIONS
If there isn't an existing UL (CUL for Canadian
Installation) listed mounting box, then read the
following instructions. Disconnect the power
by removing fuses or turning off circuit
breakers
Secure the outlet box directly to the building
structure. Use appropriate fasteners and
building materials. The outlet box and its
support must be able to fully support the
moving weight of the fan (at least 50 lbs). Do
not use plastic outlet boxes.
Figures 1 and 2 are examples of different ways
to mount the outlet box.
NOTE: You may need a longer downrod to
maintain proper blade clearance when
installing on a steep, sloped ceiling. (Fig. 3)
To hang your fan where there is an existing
fixture but no ceiling joist, you may need an
installation hanger bar as shown in Fig 3.
Outlet box
Outlet box
Fig. 1
Fig. 3
Outlet box
Fig. 2
4
WindhamTM
Fig. 5
REMEMBER to turn off the power. Follow the
steps below to hang your fan properly:
Step 1. Attach the mounting plate to the outlet
box with two screws and washers provided
with the outlet box. Make sure the mounting
plate is tight and secured. (Fig. 4)
Step 2. Lift fan into position by hanging the
motor assembly onto the hook from the ceiling
mounting plate allowing it to hang freely. (Fig. 5)
Fig. 4
5. HANGING THE FAN
CUL Listed
electrial
box
Mounting plate
Motor
Fig. 6
6. INSTALLATION OF SAFETY SUPPORT
(for Canadian Installation ONLY)
Outlet box
An additional safety support is provided to
prevent the fan from falling fan). Place the end
of cable through the loop of ceiling support
cable. Pull as much cable through loop as
possible. Feed end of cable into clamp hole
and fi rmly tighten screw (Fig. 6). Cut off
excess safety cable. Secure the safety cable
to the ceiling joist with screw and washer.
Attach safety cable
to ceiling joist with
screw and washer
5
Fig. 7
Fig. 8
Fig. 9
7. MAKE THE ELECTRIC CONNECTIONS
Remember to disconnect the power.
Follow the steps below to connect the fan to
your household wiring. Use the wire
connecting nuts supplied with your fan.
Secure the connectors with electrical tape.
Make sure there are no loose strands or
connections.
Step 1 Connect the fan supply (black) wire and
light supply (blue) wire to the black household
supply wire as shown in Figure 7.
Step 2. Connect the neutral fan (white) wire to
the white neutral household wire.
Step 3 Connect the fan ground wire (green) to
the household ground wire.
Step 4 After connecting the wires, spread
them apart so that the green and white wires
are on one side of the outlet box and the black
and the blue wires are on the other side.
Step 5 Turn the connecting nuts upward and
push the wiring into the outlet box.
Wiring
box
Ground to
mounting
bracket
or downrod
Power lines 120v
WH
BLUE
BLK BLK
WH
FAN
LIGHT
BLK
BLUE WH
WH
Light
switch
Green ground
WH
BLUE
BLK BLK
WH
GRN
Wiring
box
Ground to
mounting
bracket
or downrod
BLUE
BLK WH
WH
FAN
LIGHT
Power lines 120v
Green ground
Figures 8 and 9 illustrate the wiring
connections for optional wall control (The wire
color out of wall control may vary, see wall
control's installation manual for correct wire
connections.)
WARNING: TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR OTHER PERSONAL
INJURY. MOUNT FAN ONLY ON AN
OUTLET BOX OR SUPPORTING SYSTEM
MARKED ACCEPTABLE FOR FAN
SUPPORT.
GROUND TO
MOUNTING
BRACKET
OR DOWNROD
POWER LINES 120V
GREEN
GROUND
WIRING
BOX
WH
BLUE
BLK BLK
WH
FAN
LIGHT
WH
WH
BLUE
BLK
LIGHT FAN
6
Fig. 10
Fig. 11
WindhamTM
8. FINISHING THE INSTALLATION
Step 1. Move fan into position over the four
mounting studs and secure with the provided
washers and nuts. (Fig. 10)
Step 2. Raise the motor housing up against
the mounting plate, the four supports inside
the housing should be placed against the four
studs on mounting plate, twist the housing
clockwise until snug. (Fig. 11)
Washers
Studs
Motor
housing
Nuts
Screws
7
Fig. 12
Fig. 13
9. ATTACHING THE FAN BLADES
Step 1 Attach the blade to the blade bracket
using the screws, washers and rubber
washers as shown in Figure 12. Start screw
into bracket. Repeat for the two remaining
screws.
Step 2 Make sure the blade is straight and
tighten each screw.
Step 3 Fasten blade assembly to motor using
"Pre-Installed" mounting screws in the blade
bracket.
Screws Blade
Blades bracket
Screws
Washers
Rubber
washers
10. INSTALLING THE MOUNTING PLATE
1. Remove 1 of the 3 screws from the
mounting ring and loosen the other 2 screws.
(Do not remove)
2. Place the key holes on the mounting plate
over the 2 screws previously loosened from
the mounting ring, turn mounting plate until it
locks in place at the narrow section of the key
holes. Secure by tightening the 2 screws
previously loosened and the one previously
removed. (Fig. 13)
Mounting
plate
Mounting ring
Screws
8
WindhamTM
11. INSTALLING THE LIGHT KIT
Fig. 14
Fig. 15
NOTE: Before starting installation, disconnect
the power by turning off the circuit breaker or
removing the fuse at fuse box. Turning power
off using the fan switch is not sufficient to
prevent electric shock.
1. While holding the light kit under your fan,
snap together the wire connection plugs .
2. Carefully push all wires back into the
mounting plate, then install the light kit onto
the mounting plate with 3 screws provided. Be
sure to tighten all screws. (Fig. 14)
12. NSTALLING THE LIGHT BULBS &
GLASS SHADE
Light kit
Mounting plate
Screws
Wire connector
1. Install 3, 40W candelabra bulbs (not
included).
2. Remove the decorative nut, glass cap and
metal nut from the light kit. Place glass shade
over the light kit stem, secure with the metal
nut (rubber side on the top), glass cap and
decorative nut. Do not overtighten. (Fig. 15)
3. insert 3 pull chains through the eyelets in
the shade and cap. Secure the glass cap and
decorative nut provided. (Fig. 15)
4. Restore power and your light kit is ready for
operation.
Note: Make sure to leave enough space
between the fan pull chain and the bulbs so
the chain doesn't rub against any of the bulbs.
Light kit
Bulbs
Glass shade
Glass cap
Decorative nut
Metal nut
9
Fig. 16
Fig. 17
13. OPERATING INSTRUCTIONS
Turn on the power and check the operation of
your fan. The pull chain controls the fan speed
as follows:
1. 3-speed pull chain- it controls the fan speed
as follows: 1 pull- High, 2 pulls- Medium,
3 pulls- Low, and 4 pulls- Off.
Speed settings for warm or cool weather
depend on factors such as the room size,
ceiling height, number of fans, and so on.
2. Light kit pull chain- it controls the light kit in
"ON" or "OFF".
The pull chain controls directions: it controls
the forward or reverse.
NOTE: Tthis ceiling fan has a "REVERSE
PULL CHAIN".
NOTE: Wait for fan to stop before changing
the setting of the slide switch.
Warm weather - (Forward) A downward airflow
creates a cooling effect as shown in Fig. 16.
This allows you to set your air conditioner on a
warmer setting without affecting your comfort.
Cool weather - (Reverse) An upward airflow
moves warm air off the ceiling area as shown
in Fig.17. This allows you to set your heating
unit on a cooler setting without affecting your
comfort.
Indice
Altri manuali Kichler Lighting Fan
Kichler Lighting
Kichler Lighting Sterling Manor Manuale utente
Kichler Lighting
Kichler Lighting Cottage Grove Manuale utente
Kichler Lighting
Kichler Lighting Golden Iridescence Manuale utente
Kichler Lighting
Kichler Lighting Golden Iridescence Manuale utente
Kichler Lighting
Kichler Lighting Emerson HIGH COUNTRY Manuale utente
Kichler Lighting
Kichler Lighting FERRON Manuale utente
Kichler Lighting
Kichler Lighting 35166 Manuale utente
Kichler Lighting
Kichler Lighting Tranquil Manuale utente
Kichler Lighting
Kichler Lighting Bead Manuale utente
Kichler Lighting
Kichler Lighting Rana 310155 Manuale utente
Kichler Lighting
Kichler Lighting Arkwright Manuale utente
Kichler Lighting
Kichler Lighting 52" RENEW ENERGY STAR Manuale utente
Kichler Lighting
Kichler Lighting FRYST Manuale utente
Kichler Lighting
Kichler Lighting IMARI 300365SBK Manuale utente
Kichler Lighting
Kichler Lighting Ridley 300027OBB Manuale utente
Kichler Lighting
Kichler Lighting Hatteras Bay Patio Manuale utente
Kichler Lighting
Kichler Lighting ELLYS Manuale utente
Kichler Lighting
Kichler Lighting Verdi Manuale utente
Kichler Lighting
Kichler Lighting KAPONO Manuale utente
Kichler Lighting
Kichler Lighting HATTERAS BAY PATIOLED 60" Manuale utente
