Kichler Lighting FERRON Manuale utente
60" FERRONTM
INSTRUCTION MANUAL
Product images may vary slightly from actual product.
TABLE OF CONTENTS
SAFETY RULES...........................................................................4
5
5
6
7
10
11
12
13
TOOLS REQUIRED....................................................................
PACKAGE CONTENTS.............................................................
MOUNTING OPTIONS.............................................................
HANGING THE FAN..................................................................
INSTALLATION OF SAFETY SUPPORT...........................
ELECTRICAL CONNECTIONS..............................................
FINISHING THE INSTALLATION........................................
ATTACHING THE FAN BLADES...........................................
INSTALLING THE DECORATIVE
COVER AND DECORATIVE NUT.........................................
CONTROL SYSTEM SET-UP...................................................
13
14
16
17
18
19
20
INSTALLING THE COOLTOUCH™
CONTROL SYSTEM WALL PLATE.....................................
INSTALLING THE TRANSMITTER......................................
OPERATING INSTRUCTIONS...............................................
OPERATING INSTRUCTIONS...............................................
TROUBLESHOOTING..............................................................
60" FERRONTM | 3
4 | KICHLER.COM
SAFETY RULES
1. To reduce the risk of electric shock, insure electricity has been
turned o at the circuit breaker or fuse box before beginning.
2. All wiring must be in accordance with the National Electrical Code
and local electrical codes. Electrical installation should be
performed by a qualified licensed electrician.
3. WARNING: Not suitable for use with solid-state speed controls.
4. WARNING: To reduce the risk of fire, electric shock, or personal
injury, mount to outlet box marked "acceptable for fan support of
15.8 kg (35 lbs.) or less" and use mounting screws provided with
the outlet box. Most outlet boxes commonly used for the support
of light fixtures are not acceptable for fan support and may need
to be replaced. Due to the complexity of the installation of this fan,
a qualified licensed electrician is strongly recommended.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
OR PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED
"ACCEPTABLE FOR FAN SUPPORT".
5. The outlet box and support structure must be securely mounted
and capable of reliably supporting a minimum of 50 pounds. Use
only CUL Listed outlet boxes marked "FOR FAN SUPPORT".
6. The fan must be mounted with a minimum of 7 feet clearance
from the trailing edge of the blades to the floor.
7. To operate the reverse function on this fan, press the reverse
button while the fan is running.
8. Avoid placing objects in the path of the blades.
9. To avoid personal injury or damage to the fan and other items, be
cautious when working around or cleaning the fan.
10. Do not use water or detergents when cleaning the fan or fan
blades. A dry dust cloth or lightly dampened cloth will be suitable
for most cleaning.
11. After marking electrical connections, spliced conductors should
be turned upward and pushed carefully up into outlet box. The
wires should be spread apart with the grounded conductor and
the equipment-grounding conductor on one side of the outlet
box.
12. Electrical diagrams are reference only. Light kits that are not
packed with the fan must be CUL Listed and marked suitable for
use with the model fan you are installing. Switches must be CUL
General Use Switches. Refer to the Instructions packaged with
the light kits and switches for proper assembly.
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO
NOT BEND THE BLADE BRACKETS (ALSO REFERRED TO AS
FLANGES) DURING ASSEMBLY OR AFTER INSTALLATION. DO
NOT INSERT OBJECTS IN THE PATH OF THE BLADES.
TOOLS REQUIRED
Philips screw driver
Blade screw driver
11 mm wrench
Step ladder
Wire cutters
PACKAGE CONTENTS
i
j
f
e
g
h
a
b
c
d
Unpack your fan and check the
contents. You should have the following
items:
a. Fan blades (2)
b. Blade support plates (2)
c. Canopy & Ceiling mounting bracket
d. Ball/downrod assembly
e. Fan motor assembly
f. Decrotive cover
g. Decrotive nut
h. Allen wrench
i. Basic Function CoolTouch™ Control
System
j. Part bag contents
1) Mounting hardware:
star washers (2), wire nuts (3),
machine screws (2), washers (2),
screws (2)
2) Blade attachment hardware:
Allen screws (2), screws (8), fiber
washers (2)
3) Safety cable hardware:
wood screw, lock washer, flat
washer
4) Balance Kit
60" FERRONTM | 5
6 | KICHLER.COM
If there isn't an existing UL (cUL for Canadian Installation) listed
mounting box, then read the following instructions. Disconnect the
power by removing fuses or turning o circuit breakers.
Secure the outlet box directly to the building structure. Use
appropriate fasteners and building materials. The outlet box and its
support must be able to fully support the moving weight of the fan
(at least 50 lbs). Do not use plastic outlet boxes.
Figures 1, 2 and 3 are examples of dierent ways to mount the outlet
box.
NOTE: If you are installing the ceiling fan on a sloped (vaulted)
ceiling, you may need a longer downrod to maintain proper
clearance between the tip of the blade and the ceiling. A minimum
clearance of 12" is suggested for optimal operation.
NOTE: Depending on the location you have selected for installation,
you may need to purchase and install a "Joist Hanger" for the
support of the outlet box. Make sure the joist hanger you purchase
has been designed for use with ceiling fans. (Fig. 4)
MOUNTING OPTIONS
Fig. 1
Outlet box
Outlet box
Fig. 2
Provide strong
support
Recessed
outlet box Ceiling
mounting
plate
Fig. 3
ANGLED CEILING
MAXIMUM 20° ANGLE
Outlet box
Fig. 4
HANGING THE FAN
REMEMBER to turn o the power before you begin.
To properly install your ceiling fan, follow the steps below.
Step 1. Remove the decorative canopy bottom cover from the canopy
by turning the cover counter clockwise. (Fig. 5)
Step 2. Remove the ceiling mounting bracket from the canopy by
removing (and save one of the two screws. Loosen the remaining screw
by a half turn. (Fig. 5)
Step 3. Pass the 120 volt supply wires from the ceiling outlet box through
the center of the ceiling mounting bracket. (Fig. 6)
Step 4. Attach the ceiling mounting bracket to the outlet box using the
screws and washers included with the outlet box. (Fig.6)
Step 5. Step 5. Remove the coupling cover from the motor housing by
removing the two screws from the rim of coupling cover. (Fig. 7)
Fig. 5
Fig. 6
Fig. 7
Hanger bracket
Ceiling
canopy
Canopy
cover
Screws
Coupling
cover
Ceiling
hanger
bracket
Mounting screws (supplied
with electrical box)
UL Listed
electrial
box
120V Wires
Washers
60" FERRONTM | 7
8 | KICHLER.COM
Step 6. Remove the hanger ball from the downrod assembly by
loosening the set screw, unscrewing and removing removing the cross
pin and unscrewing the ball o the rod. (Fig. 8)
Step 7. Loosen the two set screws and remove the hitch pin and
retaining clip from the coupling on top of the motor assembly. (Fig. 9)
Step 8. Carefully feed the electrical lead wires from the fan up through
the downrod. Thread the downrod into the coupling until the Hitch pin
holes are aligned.
Next, replace the hitch pin and retaining clip. Tighten both set screws.
(Fig. 9)
HANGING THE FAN(continued)
Fig. 8
Fig. 9
Downrod
Cross pin
Hanger
ball Set screw
Supply wires
Downrod
Hitch pin
Retaining clip
Set screws
Set screws
Fig. 10
Fig. 11
HANGING THE FAN(continued)
Step 9. Slip the coupling cover, secure ring , canopy cover and canopy
onto the downrod. (Fig. 10)
Secure the coupling cover to the motor housing using the two screws
previously removed.
Thread the hanger ball onto the downrod, insert the cross pin through
the downrod and tighten. Now tighten the set screw. (Fig. 10)
Step 10. Lift the motor assembly into position and place the hanger ball
into the ceiling mounting bracket.
Rotate the entire assembly until the "Check Tab" has dropped into the
"Registration Slot" and seats firmly. (Fig. 11)
The entire motor assembly should not rotate (left or right) when seated
properly.
WARNING: Failure to reattach the cross pin and seat the "Check Tab"
can cause the fan to fall from the ceiling during operation. Take special
care to make sure this pin is reattached.
Registration slot
Downrod
Canopy
Canopy cover
Set screws
Hitch pin
Retaining clip
Coupling cover
Screws
60" FERRONTM | 9
10 | KICHLER.COM
A safety support cable is provided to help prevent the ceiling fan from
falling.
Step 1. Attach the provided wood screw and washers to the ceiling joist
next to the mounting bracket but do not tighten. (Fig. 12)
Step 2. Adjust the length of the safety cable to reach the screw and
washers by pulling the extra cable through the cable clamp until the
overall length is correct, put the end of the cable back through the cable
clamp, forming a loop at the end of the cable. Tighten the cable clamp
securely. Now, put the loop in the end of the safety cable over the wood
screw and under the washer. Tighten the wood screw securely.
NOTE: Although the safety support cable is required for Canadian
installations only. It's a good idea to make the attachment with any
installation.
INSTALLATION OF SAFETY SUPPORT
(required for Canadian installation ONLY)
Fig. 12
Ceiling mounting
bracket Attach
safety cable
to ceiling joist
with screw and
washer
Indice
Altri manuali Kichler Lighting Fan
Kichler Lighting
Kichler Lighting Arkwright Manuale utente
Kichler Lighting
Kichler Lighting Industrial Fan Manuale utente
Kichler Lighting
Kichler Lighting LYNDON Manuale utente
Kichler Lighting
Kichler Lighting 339211APP Manuale utente
Kichler Lighting
Kichler Lighting 300457 Manuale utente
Kichler Lighting
Kichler Lighting sterling manor select Manuale utente
Kichler Lighting
Kichler Lighting Cadence Manuale utente
Kichler Lighting
Kichler Lighting PINION 60 Manuale utente
Kichler Lighting
Kichler Lighting Sterling Manor Patio Manuale utente
Kichler Lighting
Kichler Lighting Humble 300415 Manuale utente
Kichler Lighting
Kichler Lighting Monarch II Manuale utente
Kichler Lighting
Kichler Lighting Decor Dorset Manuale utente
Kichler Lighting
Kichler Lighting Canfield Patio 310192 Manuale utente
Kichler Lighting
Kichler Lighting 52" RENEW DESIGNER Manuale utente
Kichler Lighting
Kichler Lighting Saxon Premier Manuale utente
Kichler Lighting
Kichler Lighting BISC 300710MWH Manuale utente
Kichler Lighting
Kichler Lighting Harbour Walk Patio Manuale utente
Kichler Lighting
Kichler Lighting Windham Manuale utente
Kichler Lighting
Kichler Lighting Rivetta Manuale utente
Kichler Lighting
Kichler Lighting Fit Manuale utente
