Kichler Lighting LYNDON Manuale utente

52" Lyndon Patio LED

TABLE OF CONTENTS

SAFETY RULES ………………………………………………………. 4

TOOLS REQUIRED ……………………………………………… 5

PACKAGE CONTENTS …………………………………………. 5

MOUNTING OPTIONS ………………………………………… 6

HANGING THE FAN ………………………………………....... 7

INSTALLATION OF SAFETY SUPPORT ……………… 9

CONTROL SYSTEM SET-UP ……………………………… 10

ELECTRICAL CONNECTIONS …………………………… 10

FINISHING THE INSTALLATION ………………………... 12

ATTACHING THE FAN BLADES …………………………… 13

INSTALLING THE MOUNTING PLATE …………………14

INSTALLING THE LIGHT KIT ………………………………… 14

INSTALLING THE BULB AND GLASS SHADE …… 15

INSTALLING THE WALL CONTROL …………………… 16

OPERATING INSTRUCTIONS ……………………………… 17

TROUBLESHOOTING …………………………………………… 18

52" Lyndon Patio LED

8. Make sure the installation site you choose allows a minimum

clearance of 7 feet from the blades to the floor and at least 30 inch

from the ends of the blades to any obstruction.

9. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be suitable

for most cleaning.

10. After making the electrical connections, spliced conductors

should be turned upward and pushed carefully up into outlet box.

The wires should be spread apart with the ground wire and white

(common) wire to one side with the black (load) wire to the other

side of the outlet box.

11. Electrical diagrams are reference only.Light kits that are not

packed with the fan must be ETL Listed and marked suitable

for use with the model fan you are installing. Switches must

be ETL General Use Switches. Refer to the Instructions

packaged with the light kits and switches for proper assembly.

SAFETY RULES

READ AND SAVE THESE INSTRUCTIONS

1. To reduce the risk of electric shock, insure electricity has

been turned o at the circuit breaker or fuse box before

beginning.

2. All wiring must be in accordance with the National

Electrical Code and local electrical codes. Electrical

installation should be performed by a qualified licensed

electrician.

3. WARNING: To reduce the risk of fire or electric shock, use

only the control provided with the fan.

4. WARNING: To reduce the risk of fire, electric shock, or

Personal Injury, mount directly to a structural framing

member or to an outlet box marked ‘Acceptable for Fan

Support of 15.9kg(35 lbs)or less’. For outlet box mounting,

use mounting screws provided with the outlet box.

5. To operate the reverse function on this fan, slide the reverse

switch to the opposite position.

6. Avoid placing objects in the path of the blades.

7. To avoid personal injury or damage to the fan and other

items, be cautious when working around or cleaning the

fan.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT

BEND THE BLADE BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR AFTER INSTALLATION.

DO NOT INSERT OBJECTS IN THE PATH OF THE BLADES.

PACKAGE CONTENTS

Unpack your fan and check the contents . You should have the following items:

A. Mounting bracket

B. Ball / downrod assembly (1)

C. Canopy

D. Canopy Trim Ring

E. Coupling Cover

F. Motor Body

G. Mounting Plate

H .Light Kit

I. Fan Blades (5)

J. Set of 5 blades arm and pre-installed

mounting screws

K. 4-watt B10 LED Bulb (3)

Phillips screwdriver

Blade screwdriver

11 mm wrench

Step ladder

Wire cutters

TOOLS REQUIRED

L. Glass Shade

M. Control Kit

N. Package Hardware

1) Mounting Hardware:

wire connectors (3)

2) Blade Attachment Hardware:

screws (15)

3) Safety Cable Hardware:

wood screw (1), spring washer (1),

flat washer (1)

4) Slip Resistant Sleeve Hardware:

slip resistant sleeve (3)

52" Lyndon Patio LED

MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian Installation) listed

mounting box, then read the following instructions. Disconnect the

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box and its

support must be able to fully support the moving weight of the fan

(at least 50 lbs). Do not use plastic outlet boxes.

box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted)

ceiling, you may need a longer downrod to maintain proper

clearance between the tip of the blade and the ceiling. A minimum

clearance of 12” is suggested for optimal operation.

NOTE: Depending on the location you have selected for installation,

NOTE: : You must use 12” or longer downrod for 30° slope (max

angle 30°). (Fig. 3)

you may need to purchase and install a “Joist Hanger” for the

support of the outlet box. Make sure the joist hanger you purchase

has been designed for use with ceiling fans. (Fig. 4)

Fig. 1

Outlet box

Fig. 2

Provide strong

support

Recessed

outlet box Ceiling

mounting

plane

Fig. 3

ANGLED CEILING

MAXIMUM 30° ANGLE

Outlet box

Fig. 4

HANGING THE FAN

REMEMBER to turn o the power before you begin installation. This is necessary

for your safety and also the proper programming of the control system.

To properly install your ceiling fan, follow the steps below.

Step 1 . Before attaching fan to outlet box (not included), ensure the outlet box is

securely fastened to at least two points to a structural ceiling member (a loose box

will cause the fan to wobble). Pass the 120 volt supply wires from the ceiling outlet

box through the center of the ceiling mounting bracket. Install mounting bracket to

outlet box in ceiling using the screws and washers included with the outlet box.

( Fig. 5)

Step 3. Remove the hanger ball from downrod assembly by loosening set screws ,

removing the cross pin, and twisting ball o the rod.( Fig. 7)

Fig. 5

Fig. 6

Outlet Box

Flat Washer

Screw

Mounting

Bracket

Fig. 7

Downrod

Cross Pin Set Screw

Hanger Ball

52" Lyndon Patio LED

Step 2.Remove one of the two shoulder screws in the mounting bracket and save it

for later use. Loosen the second shoulder screw without fully removing it. (Fig. 6)

Mounting Bracket

Shoulder Screw

Fig. 8

Fig. 9

Fig. 10

HANGING THE FAN(continued)

Step 4. Loosen the two set screws and remove the clip and cross pin from the top

coupling of the motor body.Carefully feed the fan wires up through the downrod.

Thread the downrod onto the motor coupling until the cross pin holes are aligned.

Next, replace the cross pin and clip, and tighten both set screws. (Fig.8)

Step 5. Slip the coupling cover, canopy trim ring and canopy onto the downrod.

Carefully reinstall the hanger ball onto the downrod. Make sure the cross pin is in

the correct position and the set screws are tight and the wires are not twisted.

(Fig.9)

Step 6. Now lift the motor body into position and place the hanger ball into the

hanger bracket. Rotate until the “Check Tab” has dropped into the “Registration

WARNING: Failure to properly seat the “Check Tab” can damage the ceiling fan

during operation.

Slot” and seats firmly. (Fig.10) The entire motor body should not rotate if this is

done correctly.

Clip

Cross Pin

Set Screw Motor Body

Cross Pin

Canopy

Hanger Ball

Canopy Trim Ring

Coupling Cover

Motor Body

Registration Slot

Check Tab

Set Screw

52" Lyndon Patio LED

Step 1.

NOTE:

INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan from faIling, please

install it as follows.

Drive a wood screw and washers into the side of the brace that holds the outlet

box. Leave 3mm (1/8") of space between the support brace and the washer. (Fig. 11)

Insert the safety cable through the mounting bracket and one of the holes in the

outlet box into the ceiling. Adjust the length of the safety cable to reach the screw and

washers by pulling the extra cable through the cable clamp until the overall length is

correct, put the end of the cable back through the cable clamp, forming a loop at the

end of the cable. Tighten the cable clamp securely. Now, put the loop in the end of the

safety cable over the wood screw and under the washer. Tighten the wood screw

securely. (Fig. 12)

Although the safety support cable is required for Canadian installations only.

It’s a good idea to make the attachment with any installation.

Step 2.

Fig. 11

Flat Washer

Wood Screw

Spring Washer

Outlet Box

Support Brace

Ceiling

Fig. 12

Safety Cable Bolt Wood Screw

CONTROL SYSTEM SET-UP

NOTE: The wall control and receiver have 16 dierent code combinations. To prevent possible

interference from or to other remote units, simply change the combination code on the receiver

and wall control as below.

Step 1. Slide the code switches on the receiver to your choice of either up or down using a small

ballpoint pen (not included). (Fig. 13)

Step 2. To set the code on the wall control, use a small flat screwdriver and gently pry it apart

from the top or bottom of the switch plate. Slip the code switches to the same positions as set

on the receiver. (Fig.13)

NOTE: Factory setting is all up. Do not use this position.

NOTE: If you are using more than one fan in the same area and want to control them separately,

change code switches on receiver and wall control to a new setting.

Step 3. Install the 23A 12V battery (included) with wall control system and make sure it is seated

correctly. Replace the switch plate. (Fig. 14)

NOTE: Remove battery if remote has not been used for a long period of time in order to avoid

damage. Store wall control away from excessive heat or humidity.

ELECTRICAL CONNECTIONS

WARNING: To avoid possible electrical shock, be sure you have turned o the power at the main

circuit panel before wiring.

Follow the steps below to connect the fan to your household wiring. Use the wire connectors

supplied with your fan. Secure the connector with electrical tape. Make sure there are no loose

wire stands or connections.

WARNING: If your house wires are dierent colors than referenced in this manual, stop

immediately. A professional electrician is recommended to determine proper wiring.

Step 1. Insert the receiver into the mounting bracket, and keep flat in opposition of ceiling. (Fig. 15)

Fig. 13

Fig. 14

Fig. 15

Code Switch

Receiver

Switch Plate

Wall Control

Battery

Receiver

Mounting Bracket

Switch Plate

Altri manuali per LYNDON

Indice

Lingue:

Altri manuali Kichler Lighting Fan

Kichler Lighting

Kichler Lighting Monarch II Patio Manuale utente

Kichler Lighting

Kichler Lighting Select Dorset Manuale utente

Kichler Lighting

Kichler Lighting PINION 60 Manuale utente

Kichler Lighting

Kichler Lighting Cameron 310204WH Manuale utente

Kichler Lighting

Kichler Lighting Ried 300356 Manuale utente

Kichler Lighting

Kichler Lighting Ample Manuale utente

Kichler Lighting

Kichler Lighting Pacific Edge 300157 Manuale utente

Kichler Lighting

Kichler Lighting Harbour Walk Patio Manuale utente

Kichler Lighting

Kichler Lighting HATTERAS BAY PATIOLED 60" Manuale utente

Kichler Lighting

Kichler Lighting 300370 Manuale utente

Kichler Lighting

Kichler Lighting Humble 300415 Manuale utente

Kichler Lighting

Kichler Lighting Cottage Grove Manuale utente

Kichler Lighting

Kichler Lighting 52" Chiara LED Manuale utente

Kichler Lighting

Kichler Lighting True Manuale utente

Kichler Lighting

Kichler Lighting Kyte 50 Manuale utente

Kichler Lighting

Kichler Lighting Renew Select Patio Manuale utente

Kichler Lighting

Kichler Lighting 35166 Manuale utente

Kichler Lighting

Kichler Lighting Deckard Manuale utente

Kichler Lighting

Kichler Lighting Tide Weather+ Manuale utente

Kichler Lighting

Kichler Lighting Rana 310155 Manuale utente

Kichler Lighting

Kichler Lighting Hatteras Bay Patio Manuale utente

Kichler Lighting

Kichler Lighting Tranquil Manuale utente

Kichler Lighting

Kichler Lighting Lija Manuale utente

Kichler Lighting

Kichler Lighting Cadence Manuale utente

Manuali Fan popolari di altre marche

ELTA FANS

ELTA FANS H03VV-F Manuale utente

Hunter

Hunter 20714 Manuale di istruzioni

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuale utente

Hunter

Hunter Caraway Manuale di istruzioni

Panasonic

Panasonic FV-15NLFS1 Manuale utente

Kompernass

Kompernass KH 1150 Manuale utente

VES

VES FALA100/12V/TR Manuale utente

Vertiv

Vertiv Liebert DCD Manuale utente

Westinghouse

Westinghouse GFP Series Manuale utente

Venmar

Venmar KUBIX HRV PLUS Series Manuale utente

Maico

Maico ECR 31 Manuale utente

Sonnenkonig

Sonnenkonig Dinky Manuale utente

S&P

S&P ECOWATT HXBR Manuale utente

Wider

Wider IMP03369BH Manuale utente

Panasonic

Panasonic F-60DHN Manuale utente

Hinkley

Hinkley HIGHLAND Manuale utente

Broan

Broan 766BN Manuale utente

Premium

Premium PFS16022 Istruzioni per il montaggio