Kicker KSMT25 Manuale utente

Altri manuali per KSMT25

1

Questo manuale è adatto per i seguenti modelli

1

Indice

Altri manuali Kicker Altoparlanti

Manuali Altoparlanti popolari di altre marche

argon audio

argon audio IE20 Manuale utente

Denon

Denon SC-N7 Manuale utente

Gemline

Gemline Ace 3952 Manuale utente

Focal

Focal ON WALL 300 Manuale di istruzioni

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuale utente

SoundLogic

SoundLogic BCCS-6/6395 Manuale utente

Peavey

Peavey DTH 218 Manuale utente

Avantree

Avantree Pluto Air Manuale utente

Morel

Morel Integra Series INTEGRA OVATION 4 Manuale utente

Oppo

Oppo SONICA Manuale utente

Bose

Bose SoundLink Wireless Music System Manuale utente

Rocksteady

Rocksteady Stadium Manuale utente

Bowers & Wilkins

Bowers & Wilkins 4 Manuale utente

Sonance

Sonance SONOS OUTDOOR Series Manuale utente

Electro-Voice

Electro-Voice EVID FM4.2 Manuale utente

Pioneer

Pioneer XW-HTD630 Manuale utente

Onn

Onn BWA16AA002 Manuale utente

HP

HP GL313AA - USB Speakers PC Multimedia Manuale utente

EOP2021-CS4

5/26/2021

REV-A.1

49KSMT25 Installation Guide

Page 1of 6

The Kicker KSMT25 pod provides a mid and tweeter with optimized adjustability. The

pod can be mounted to almost any surface where a hole can be drilled. Not only does the entire

pod assembly pivot, lean, and rotate on the ball and socket mounting stud - the tweeter also has

approximately 260 degrees of planetary rotation around the mid to provide desired orientation.

This document demonstrates adjusting, mounting, and wiring of the KSMT25 pod assembly for

the following Kicker models:

•47KSMT2504

PARTS IDENTIFICATION

Below is a list describing part names used in these instructions.

(1) KSMT25 pod assembly

(2) Tweeter

(3) Mid

(4) Mounting Stud

(5) Decorative Plug

(6) Washer

(7) Wing Nut

READ AND UNDERSTAND ALL OF THESE INSTRUTIONS BEFORE

INSTALLATION!

(1)

(2)

(3)

(4)

(5)

(6)

(7)

EOP2021-CS4

5/26/2021

REV-A.1

49KSMT25 Installation Guide

Page 2of 6

ADJUSTABILITY OF THE KSMT25 POD

The KSMT25 tweeter pod assembly pivots and rotates on its mounting stud. This can be

accomplished any time before or after installation.

1. To adjust the rotation of the tweeter around the mid, remove the decorative plug at the

back of the pod assembly. Using a 2.5mm allen wrench, loosen (do not remove) the bolt

retaining the tweeter to the mid.

2. Rotate the tweeter to the desired location and retighten the bolt. Replace the decorative

plug.

EOP2021-CS4

5/26/2021

REV-A.1

49KSMT25 Installation Guide

Page 3of 6

TIGHTENING THE BALL AND SOCKET MOUNT

If the pod assembly will not remain stationary on the stud, the ball and socket clamp can

be tightened to prevent pod movement.

1. Remove the nut and washer from the stud.

2. Using a 2mm allen wrench, tighten the three bolts on the bottom of the pod to increase

clamping force on the ball and socket.

MOUNTING THE KSMT25 TWEETER POD

Choose a mounting surface that can be accessed from both side as a wing nut must be

installed on the mounting stud to retain the pod in its location.

1. Drill a 5/8” in the desired mounting location.

EOP2021-CS4

5/26/2021

REV-A.1

49KSMT25 Installation Guide

Page 4of 6

2. Place the washer on the mounting stud then insert the mounting stud into the drilled hole

Secure the pod assembly to the mounting surface with the wing nut.

CONNECTING THE CROSSOVERS TO THE PODS

DANGER! Electrical hazard. Burns, electric shock, or damage to equipment

may occur during connection of electrical wires. Always disconnect the vehicle’s

power source before making wire connections.

Kicker supplies crossovers with KSMT25 to optimize the sound of the pod’s speakers.

The KSMT25 crossover is terminated so that it will only connect to the KSMT25 assembly.

EOP2021-CS4

5/26/2021

REV-A.1

49KSMT25 Installation Guide

Page 5of 6

NOTE: The KSMT25 crossover is labeled with the part number 47KSMT25-XO.

1. Connect the crossover terminals and receptacles to their respective mating connector on

the KSMT25 pod assembly. The terminals on the 47KSMT25 crossover are all different

sizes and types to prevent incorrect connection. Also, the crossover wire colors match the

pod assembly wire colors.

EOP2021-CS4

5/26/2021

REV-A.1

49KSMT25 Installation Guide

Page 6of 6

2. Slide the clear cover over the terminals to prevent a short circuit.

3. Connect the crossover input to the outputs of the head unit or amplifier using the supplied

butt connectors. The positive lead is the wire with gray insulation labeled with a “plus”

symbol. The negative lead has gray insulation with a black stripe on it.