Kilotech KPOS 1530 Manuale utente

www.kilotech.com

KPOS 1530, 851508, Page 1 of 9

KPOS 1530

851508 POS Scale 15 kg

Pole with display (optional)

Version 1.0

Quick Start Manual

Contents subject to change without notice

KPOS 1530, 851508, Page 2 of 9

Introduction

Thank you for choosing a Kilotech Scale. We appreciate your business and hope that you will enjoy using your

scale. Should you require Technical Support, please contact your local dealer from whom you have purchased.

Our own Technical Service Department can be reached at 800-694-4445 ext.6023 (Canada) or 877-328-5988 ext

6023 (USA). Happy Weighing!

Avoid lengthy exposure to heat or cold. Allow the scale to acclimate to normal room temperature

before use.

Allow sucient warm up me. Turn the scale on and wait for a few minutes to allow the

internal components a chance to stabilize before weighing.

Do not leave a load or weight on a scale for a prolonged

period of me.

Do not tamper with the scale yourself. This will void the warranty. Contact your local distributor or

Kilotech directly to properly repair your scale.

Do not dissemble the scale yourself. This will void the warranty. Contact your local distributor or

Kilotech directly to properly repair your scale.

Do not overload beyond the maximum weight limit.

Do not pull the plug by its cord when unplugging.

Do not use the scale near re or corrosive gas.

Unless the scale is waterproof do not spill water or immerse

in water.

Avoid placing the scale near a heater. It could cause a uctuaon to the indicator reading.

Always make sure to use a Kilotech approved adapter.

Do not drop the scale or apply a sudden shock.

Do not drag the scale.

Avoid exposing to other electromagnec devices. These devices emit RF and can cause unstable readings. If

your scale should perform poorly, try moving the scale to a

dierent room or locaon.

Level the scale or make sure it is on an even surface. A scale used on an uneven surface may provide an unstable

reading.

Scale should be used within stated temperature

& humidity limits.

General Precautions

KPOS 1530, 851508, Page 3 of 9

Product Number 851508

Capacity 15 kg / 30 lb / 480 oz

Graduaon 0.005 kg / 0.01 lb / 0.2 oz

Weighing Modes kg, lb, oz

Display 5 ½ digits, 7 segment, 0.58"(15 mm) LCD

Back Light Blue backlight. Choice of a permanent backlight or you can

set it so it works when an item is placed on the plaer.

Auto Power O

Power Adapter AC, 7-9 V DC, ≥ 500mA or USB

Product Dimensions 355mm x 305mm x 88.5 mm / 14"x 12"x 3.5"

Plaer Size 355mm x 305mm / 14"x 12"

Operang Temperature / Humidity -10° C - 40° C / 14° F - 104° F / 10 -90% RH without

condensaon

Input Signal Range

Display Resoluon

RS232 Yes

Checkweighing Funcon

Counng Feature

Measurement Canada and NTEP approval number

Specifications

KPOS 1530, 851508, Page 4 of 9

General key description

Please note that this is a general funcon descripon. Some of the keys described below might not be available

on your scale. The key examples in this manual are included solely for illustrave purposes. Color or shape of

icon might be dierent.

On/Off Key

This key is used to power the scale on and o. With some scale models, this key is also used to exit from the

program menu. On some scales the on/o key is only present as the main switch located at the boom of the

scale and not as a buon.

Zero key

The zero key can be used to correct a deviaon from zero. Press the Zero key to return to a zero value.

The most common cause of a zero deviaon is debris on the plaer, leaving objects on the plaer for excessive

periods of me, or near empty baery.

Used to Scroll between values and enter in to menu step.

qBacklight

Specification

KPOS 1530, 851508, Page 5 of 9

Interface details

Keypad: 3 push buons

Load cell excitaon:

5Vdc,

Maximum current: 20mA

Communicaon:

Oponal serial port: USB (Virtual RS232), RS232

Baud rate: selectable: 1200-2400-4800-9600-19200-38400 bps

Data output format: 8N1, 7O1, 7E1

Protocol: Programmable

Faceplate

Illuminates when the scale is at zero and the gross weight is 0

lb Illuminates when the measure of unit is lb

oz Illuminates when the measure of unit is oz

kg Illuminates when the measure of unit is kg

KPOS 1530, 851508, Page 6 of 9

Normal weighing mode

Calibraon switch is o

Use the MENU key to toggle between AL.ON , WT.ON , or AL.OFF.

AL.ON = backlight on

WT.ON = backlight automacally is on during key operaon or when changing weight and will auto o aer 30

seconds have elapsed.

AL.OFF= backlight o

Press zero to conrm the seng. The scale will revert back to normal weighing mode.

Operation Menu Structure

Power on the scale: When the scale is o, press ON / OFF to turn it on;

Power o the scale: When the scale is on, press ON / OFF to turn it o;

ZERO: When the weight is stable and within the zero range (2% FS), press the ZERO key to set

the new zero point.

When the weight superceeds the zero range, press the ZERO key to tare the weight.

Symbol Denions and Troubleshong

0 The zero point is higher than the seng range.

0The zero point is lower than the seng range.

AD Signal to ADC is higher than the seng range.

AD Signal to ADC is lower than the seng range.

The weight is higher than the upper limitaon, or the

display data is over limitaon.

The weight is below the lower limitaon.

EEP.E1 The parameters CONFIG or CAL are not correctly set.

EEP.E2 USER parameter is not correctly set.

CAP.- - - Capacity will be the next displaying content.

CAP.ER Capacity parameters are not correct.

OFF Power OFF the indicator.

KPOS 1530, 851508, Page 7 of 9

Operation

KPOS 1530, 851508, Page 8 of 9

Troubleshoong

Symptom Possible Cause Soluon

Ad Load cell wires that are connected to the

indicator are:

a) incorrectly connected, b) shorted or c)

open; Another possibility is that the ADC,

load cell is damaged.

a) Make sure the wires are ok and that

they are correctly connected.

b) Replace the load.

0The zero point is higher than the seng

range.

a) Make sure the scale plaorm is empty.

b) Perform the zero calibraon.

0The zero point is lower than the seng

range.

a) Install plaorm on scale.

b) Perform the zero calibraon.

The weight reading exceeds the overload

limit or the weight value cannot be dis-

played in the current unit of measure as it

exceeds 6 digits.

a) Reduce the load on the scale unitl the

weight value can be dislayed.

b) Use a more appropriate weight

measure.

c) Reset some parameters in CONFG or

USER.

Weight reading is below the Under load

limit.

a) Install plaorm on scale.

b) Perform the zero calibraon.

EEP.E1 CONFIG or CAL parameters are

not correctly set.

Reset the items in CONFG and

recalibrate.

EEP.E2 USER parameter is not correctly set. Reset the items in USER.

CAP.ER Capacity parameters are not correctly set. Set PRIM.N / PRIM.d / SECD.N to the cor-

rect number and make sure the capacity

is not more than 6 digits.

The scale will not turn on a) The power cord is not plugged in.

b) The power cord is not properly

connected.

c) The Power outlet is not supplying

electricity.

a) Check the power cord connecons.

b) Make sure the power cord is plugged

into the power outlet.

c) Check power source.

The scale will either not zero when

turned on or it will not display zero

a) Load on scale may exceed allowable

limits.

b) The load on the scale may not be

stable.

c) The load cell may be damaged.

a) Remove the load from the scale.

b) Wait for the load to become stable.

KPOS 1530, 851508, Page 9 of 9

Packing List

No. Item Qty

1 Scale 1

2 Quick Start Guide 1

3 AC Adapter 1

4 RS232 cable 1

5 USB cable 1

6Post display opon Oponal

VERSION DESCRIPTION DATE

V1.0 Inial version 2014-4-22

Altri manuali per KPOS 1530

Indice

Altri manuali Kilotech Scala

Kilotech

Kilotech KPC 1500 SS Manuale utente

Kilotech

Kilotech KPS 60 Manuale utente

Kilotech

Kilotech KRS SWP Series Manuale utente

Kilotech

Kilotech CTR Series Manuale utente

Kilotech

Kilotech KSB series Manuale utente

Kilotech

Kilotech KBS Series Manuale utente

Kilotech

Kilotech Abacus AB30 Manuale utente

Kilotech

Kilotech KPC 2000 Manuale utente

Kilotech

Kilotech KPC 160 Manuale utente

Kilotech

Kilotech KPC 1500SS Manuale per l'uso e la cura

Kilotech

Kilotech KPS 60 SS Manuale per l'uso e la cura

Kilotech

Kilotech Integrator LE.3k Manuale utente

Kilotech

Kilotech 851340 Manuale di installazione

Kilotech

Kilotech KLE 200 Manuale utente

Kilotech

Kilotech KPC 5000 Manuale di istruzioni

Kilotech

Kilotech Integrator C30 Manuale utente

Kilotech

Kilotech KIN 500 Manuale utente

Kilotech

Kilotech MS-4202L Adult Manuale utente

Kilotech

Kilotech KPOS 1530 Manuale utente

Kilotech

Kilotech KHS 200-30 Manuale utente

Kilotech

Kilotech 851340 Manuale utente

Kilotech

Kilotech KPC 5000 Manuale utente

Kilotech

Kilotech KWD 750SS Manuale utente

Kilotech

Kilotech KWD 15K Manuale utente

Manuali Scala popolari di altre marche

AWS

AWS ZEO-50 Manuale utente

Gima

Gima Glass Body Fat Analyzer Manuale elenco delle parti

Seca

Seca 374 Manuale utente

TEC

TEC TEC SL59 SERIES Manuale utente

Axis

Axis B/E Series Manuale utente

Alecto

Alecto ACW-40 Manuale utente

Rice Lake

Rice Lake MSI-4260 IS Manuale utente

IKA

IKA RCT basic safety control Manuale utente

ADE

ADE M20011 Manuale utente

Duronic

Duronic KS3000 Manuale utente

Digi

Digi SM-720 Manuale utente

Cardinal

Cardinal CS Series Manuale utente

Korona

Korona Kastella Manuale utente

A&D

A&D FC-50Ki Manuale utente

BDA

BDA CAMARGUE Manuale utente

Tanita

Tanita HD-357 Manuale utente

Leifheit

Leifheit 03173 Manuale utente

Lumme

Lumme LU-1340 Manuale utente