Kingfisher KI9800 Manuale utente

KI 9000 UM-10 45

QUICK REFERENCE GUIDE –KI 9800 Series Optical Light Source

To remove interchangeable connector adaptor, press

the button on the front of the instrument and pull off

adaptor.

To defeat auto power-off, press and hold [POWER] for

3 seconds during turn on. ‘Perm’ is displayed on the top

right of the LCD.

Low battery is indicated with a battery symbol.

During instrument turn on:

-to view all display segments, press and hold [].

-to display firmware version, press and hold

[LEVEL].

-to turn buzzer off, press and hold [].

To enable source emitter, press [] or [] after

turning on instrument. Operating wavelengths will be

shown in the top corner on the right hand side and

source power level on the left hand side. Do not enable

a laser when there is no fibre attached to the optical

output connector.

To scroll wavelength, press [] or [].

ToneMode:

Modulation is active only while the source emitter is

enabled. To select a modulation tone, press [MOD] to

scroll through available settings.

Press and hold [MOD], then press [] to step down

or [] to step up the modulation tone or fiber ID

number.

Press and hold [MOD], then press [] for 3 seconds

to turn off modulation.

Press and hold [MOD], then press [] for 3 seconds

to advance to ID12.

To exit, press [MOD] for 3 seconds. Alternatively, press

[POWER] while holding [MOD].

Laser Output Power Adjustment (not available on LED source)

To decrease the laser output power, turn the laser ‘on’,

then press [LEVEL].

Press and hold [LEVEL], then press [] to step down

or [] to step up the output power.

Press and hold [LEVEL], then press [] for 3

seconds to set output power to the lowest level.

KI 9000 UM-10 46

QUICK REFERENCE GUIDE –KI 9800 Series Optical Light Source

Press and hold [LEVEL], then press [] for 3

seconds to set output power to factory default.

Alternatively, press [POWER].

AutoTest:

To start AutoTest, press [POWER] then press [AUTO].

To end, press [AUTO] again or turn the instrument off.

TamperLock Mode:

While in TamperLock Mode, user is prevented from

changing wavelength or laser output power.

Press [POWER], turn the emitter on, then press and

hold [] while pressing [LEVEL] for 5 seconds.

Display will show “codE’.

Enter 6 key sequence using any keys except

[POWER]. Triple beep and “LOut” on display will

indicate completion. To cancel your entry before

completion, press [POWER].

While TamperLock is active, “<<<”and “>>>” symbols

will be displayed.

To clear TamperLock Mode, turn off instrument then

press [POWER] while holding down [] and

[LEVEL]. When display show “codE”, enter six key

sequence.

If the correct sequence had been entered, “PASS” will

be displayed indicating that TamperLock had been

cleared.

In case where entered sequence was not correct,

“FAIL x” will be displayed (where x is attempt count).

TamperLock will be cleared after three unsuccessful

attempts.

Altri manuali per KI9800

Questo manuale è adatto per i seguenti modelli

Altri manuali Kingfisher Apparecchiature di prova

Kingfisher

Kingfisher KI 2400 Series Manuale utente

Kingfisher

Kingfisher KI 7340 Series Manuale operativo

Kingfisher

Kingfisher KI2000 Series Manuale utente

Kingfisher

Kingfisher KI 2300 Series Manuale utente

Kingfisher

Kingfisher KI7300 Series Manuale di istruzioni

Kingfisher

Kingfisher KI7343C-InGaAs Manuale utente

Kingfisher

Kingfisher KI2000 Series Manuale operativo

Kingfisher

Kingfisher KI 2400 Series Guida all'installazione

Kingfisher

Kingfisher KI7343C-InGaAs Manuale utente

Kingfisher

Kingfisher KI23400 Series Manuale utente

Kingfisher

Kingfisher KI7400 Series Guida all'installazione

Kingfisher

Kingfisher KI021-1 Manuale utente

Kingfisher

Kingfisher KI7347C Series Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente