Kramer 691 Manuale utente

691 Quick Start (P/N: 2900-300523QS REV 2)

P/N:

2900- 300523QS

Rev:

Scan for full manual

691 Quick Start Guide

This guide helps you install and use your 691 for the first time.

Go to www.kramerav.com/downloads/691 to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

691 HDBT 2.0 Optical Transmitter

4 Rubber feet

1 Power adapter (12V DC)

1 Quick start guide

Step 2: Get to know your 691

Feature

Function

USB Connector

Connect to the USB host for traffic extension, (for example, a laptop)

LINK LED

Lights green when the HDBT link is valid

IN LED

Lights green when an HDMI active signal device is connected

ON LED

Lights green when the device receives power

Feature

Function

HDMI IN Connector

Connect to the HDMI source

IR 3.5mm Mini Jack Connector

Connect to an external infrared transmitter or sensor for traffic extension

RS-232 3-pin Terminal Block

Connect to an RS-232 transmitter for traffic extension (for example, a PC to control the

projector)

AUDIO IN 3.5mm Mini Jack

Connect to the stereo, analog audio source for traffic extension

OUT IN SFP+ Connector

Connect the fiber optic cable to the OUT IN SFP+ LC connector

SETUP 4-way DIP-switch

Sets the device behavior

CONTROL

RS-232 3-pin

Terminal Block

Connect to the serial controller to control this device

ETHERNET RJ-45

Connector

Connect to the Ethernet controller to control this device or to a LAN to extend network traffic to

the receiver

RESET Switch

Press and hold while power-cycling the device to reset to factory default parameters

PROG Mini USB Connector

Connect to a PC to perform firmware upgrades

12V DC Power Connector

Connect to the supplied power adapter

Step 3: Install the 691

To mount the 691 in a rack, use an RK-1 rack adapter. Alternatively, attach the rubber feet to the underside of the 691 and place it

on a table.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your 691. For best results, we recommend that you always use Kramer high-

performance cables to connect AV equipment to the 691.

To install the OSP SFP+ transceiver:

1. Make sure the bail is pushed up, in the closed position.

2. Insert the OSP SFP+ transceiver into the relevant optical device SFP+

slot and push it in until it clicks.

Remove the protective cap and store it in a safe place for future use.

Warning: Connecting the OSP SFP+ connector to an LC(APC) fiber

connector may cause poor performance and damage the connector!

Refer to www.kramerav.com/downloads/OSP-MM1 for more information.

Warning: Class 1 Laser Product

Invisible laser radiation present.

Avoid long-term viewing of laser.

Avoid the use of magnifying viewing aids or instruments (such as binoculars, telescopes, microscopes and magnifying

lenses, but not spectacles or contact lenses).

Avoid placing optical devices in the emitted beam that could cause the concentration of the laser radiation to be

increased.

RJ-45 Pinout:

SETUP DIP-Switches

For the Ethernet connectors, see the proper

wiring diagram

A DIP-switch that is down is on, up is off. Changes to the DIP-switches only take

effect on power-up. After changing a switch, reboot the device.

PIN EIA /TIA 568B

Wire Color

Function

Status

Orange / White

For future use

Orange

Audio source priority

Off—Embedded audio (factory default)

On—Analog audio

Green / White

Blue

EDID lock

Off—Automatic EDID acquisition (factory default)

On—Lock (locks the current EDID so that changes

on the output do not result in changes to the EDID)

Blue / White

Green

Brown / White

Audio mode selection

Off—Auto (factory default)

On—Manual

Brown

Step 5: Connect the power

Connect the power adapter to the 691 and plug the adapter into the mains electricity.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit

Warning:

Use only the Kramer Electronics power supply that is provided with the unit

Warning:

Disconnect the power and unplug the unit from the wall before installing

See www.KramerAV.com for updated safety information.

Step 6: Control the 691 via the:

Embedded Web pages:

RS-232 and Ethernet:

RS-232

Protocol 3000

Baud Rate:

115,200

Stop Bits:

Data Bits:

Parity:

None

Command format:

ASCII

Example (get device model name):

#model?<cr>

TCP/IP Parameters

IP Address:

192.168.1.39

UDP Port #:

50000

Subnet mask:

255.255.000.000

TCP Port #:

5000

Default gateway:

192.168.0.1

Full Factory Reset

Rear panel button:

Press and hold to reset to factory default parameters

P3K command:

#factory<cr>

Embedded Web pages:

Select Device Settings page and click Factory reset

Default Parameters

Value

Name:

KRAMER_

Model:

691

Audio delay input switching on newsignal:

Immediate

Audio delay input switching on signal loss (leave 5V on):

5 seconds

Audio delay input switching on cable unplug:

Immediate

Video delay power off 5V on signal loss:

15 minutes

HDCP:

Follow output

Web Logon credentials:

Name: Admin; Password: Admin

Technical Specifications

Inputs:

1 HDMI on a female HDMI connector

1 Stereo analog unbalanced audio on a 3.5mm mini jack

Outputs:

1 Fiber Optic on an 10Gbps SFP+ LC connector complying with IEEE 802.3ae

Ports:

1 IR on a 3.5mm mini jack forIR link extension

1 USB on a female USB-B connector for USB link extension

1 Mini-USB connector for device Firmware upgrade

1 RS-232 on a 3-pin terminal block for serial link extension

1 RS-232 on a 3-pin terminal block for device control

1 10Base-T/100BaseTx Ethernet on an RJ-45 female connector for device control and

network traffic transfer

Fiber Extension Line:

HDBaseT 2.0 compliant

For optimum performance use the recommended multimode or singlemode Kramer SFP+

transceivers available at www.kramerav.com/product/691

Video:

Up to 10.2Gbps bandwidth (3.4Gbps per graphic channel); Up to 4K UHD @60Hz (4:2:0)

24bpp resolution; HDMI 2.0 and HDCP 1.4 signal compliance

Analog Audio:

Up to 1 Vrms level, 0.03% THD + NOISE @ 1kHz at nominal level

Extended USB:

1.1 and 2.0 Host compliance; Up to 127Mbps (out of max 480 USB) extended line rate

bandwidth; Up to 7 devices; Up to 2 hubs; Up to 8 ports per hub

Extended RS-232:

300 to 115200 baud rate

Control RS-232:

115200 baud rate

Cooling:

Convection ventilation

Operating Temperature:

0° to +40°C (32° to 104°F)

Storage Temperature:

-40° to +70°C (-40° to 158°F)

Humidity:

10% to 90%, RHL non-condensing

Power Consumption:

12V DC, 1300mA

Dimensions:

21.46cm x 16.3cm x4.36cm (8.45" x6.42" x 1.7") W, D, H

Shipping Dimensions:

35.1cm x 21.2cm x 7.2cm (13.82" x 8.35" x 2.8") W, D, H

Weight:

0.95 kg (2.1lbs)

Shipping weight:

1.45 kg (3.2lbs) approx.

Included Accessories:

Power supply (12V, 2A)

Options:

For optimum range and performance use the recommended USB, Ethernet, serial and IR

Kramer cables available at www.kramerav.com/product/691

Specifications are subject to change without notice at www.kramerav.com

Altri manuali per 691

Questo manuale è adatto per i seguenti modelli

Altri manuali Kramer Trasmettitore

Kramer

Kramer 650T Manuale utente

Kramer

Kramer SID-X1 Manuale utente

Kramer

Kramer PT-2UT/R-KIT Manuale utente

Kramer

Kramer WP-110xl Manuale utente

Kramer

Kramer TP-15 Manuale utente

Kramer

Kramer TP-202 Manuale utente

Kramer

Kramer WP-580Txr Manuale utente

Kramer

Kramer TP-205A Manuale utente

Kramer

Kramer PT-572HDCP+ Manuale utente

Kramer

Kramer WP-789T Manuale utente

Kramer

Kramer TP-583Txr Manuale utente

Kramer

Kramer TP-114 Manuale utente

Kramer

Kramer RC-116 Manuale utente

Kramer

Kramer VP-428H2 Manuale utente

Kramer

Kramer TP-581T Manuale utente

Kramer

Kramer 617T Manuale utente

Kramer

Kramer VP-300THD Manuale utente

Kramer

Kramer TP-185 Manuale utente

Kramer

Kramer PT-571HDCP Manuale utente

Kramer

Kramer WP-871xr Manuale utente

Kramer

Kramer 610T Manuale utente

Kramer

Kramer 622T Manuale utente

Kramer

Kramer TP-210 Manuale utente

Kramer

Kramer TP-551N Manuale utente

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente