Kramer WP-871xr Manuale utente

WP-871xr Quick Start

P/N:

2900- 301061QS

Rev:

Scan for full manual

WP-871xr Quick Start Guide

This guide helps you install and use your WP-871xr for the first time.

Go to www.kramerav.com/downloads/WP-871xr to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

WP-871xr HDMI 4K Line Transmitter

1 Quick start guide

1 Power adapter (with open DC head) and cord

Frame (or frame set) and faceplate

Step 2: Get to know your WP-871xr

Feature

Function

HDMITM IN Connector

Connects to an HDMI source.

STATUS LED

Lights green when power is connected to the device.

Lights blue when powered and both active source and acceptor are detected.

Ring Tongue Terminal Grounding

Screw

Connect to grounding wire (optional).

Power Supply 2-pin Terminal Block

Connector

To Connect to a power supply (if required). Connect GND to GND, +12V to +12V.

DGKat-2.0 OUT RJ-45 Connector

Connect to the DGKat-2.0 IN connector on the using CAT 6A cable.

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Front Panel –Before assembly

Feature

Function

SETUP DIP-switches

Do not change the default DIP-switch settings (located on the front panel)

DIP-switch 1

Compression

ON (right) –High compression level for additional range extension

(default).

DIP-switch 2

Compression Setup

OFF (left) –Enable compression (default).

ON (right) –For future use.

Step 3: Install the WP-871xr

Insert the device into the in-wall box (note that first you need to connect the DGKAT 2.0 cable and power) and connect

the parts as shown in the illustrations below:

European Version

US Version

We recommend that you use any of the following standard 1 Gang in-wall junction boxes (or their equivalent):

US: 1 Gang US electrical junction boxes.

EU: 1 Gang in-wall junction box, with a cut-hole diameter of 68mm and depth that can fit in both the device and the

connected cables (DIN 49073).

UK: 1 Gang in-wall junction box, 75x75mm (W, H) and depth that can fit in both the device and the connected cables

(BS 4662).

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your WP-871xr. For best results, we recommend that

you always use Kramer high-performance cables to connect AV equipment to the WP-871xr.

We highly recommend using only Kramer UNIKAT cables with these products. If using 3rd party shielded CAT 6A

cables, both ends of the shield must be soldered to the connectors for the products to function properly. Do not use

any jumpers, unshielded wall plates or mid-span cable connections. These extenders are not compatible with

HDBaseT technologies. Prior to signal extension, ensure that the extension line cable is lying straight and not coiled.

Step 5: Connect the power

Connect the 12V power adapter to the remote device (for example, PT-872xr) or to WP-871xr if needed, and plug the power

supply into the mains electricity. This device provides power to its counterpart via DGKat 2.0. Each device can provide or

accept power over cable (PoC) via DGKat 2.0.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the Kramer Electronics power supply that is provided with the unit.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

Technical Specifications

Inputs

1 HDMI

On a female HDMI connector

Outputs

1 DGKAT 2.0

On a female RJ-45 connector

Video

Transmitted Data

Bandwidth

Up to 18Gbps (6Gbps per graphic channel)

Max Resolution

3840x2160@60Hz (4:4:4) 24bpp

Compliance

HDMI 2.0, HDCP 2.2, HDR 10

Reach Extension

We recommend that you use Kramer shielded cables to achieve optimum extension ranges.

High Compression Level

Up to 60m (200ft) at 4K@60Hz (4:4:4)

Up to 70m (230ft) at 4K@60Hz (4:2:0) or full HD (1080p

@60Hz 36bpp)

Control

Behind Frame

DIP-switches

Power

Consumption

12V DC, 600mA when coupled with a compatible receiver

Source

12V DC, 2A

Environmental Conditions

Operating Temperature

0° to +40°C (32° to 104°F)

Storage Temperature

-40° to +70°C (-40° to 158°F)

Humidity

10% to 90%, RHL non-condensing

Regulatory Compliance

Safety

CE, UL

Environmental

RoHs, WEEE

Enclosure

Net Dimensions (W, D, H)

US: 7cm x 3.1cm x 11.4cm (2.8" x 1.2" x 4.5)

EU: 8cm x 3.1cm x 8cm (3.1" x 1.2" x 3.1)

UK: 8.6cm x 3.1cm x 8.6cm (3.4" x 1.2" x 3.4")

Shipping Dimensions (W,

D, H)

23.2cm x 13.6cm x 10cm (9.1" x 5.4" x 3.9")

Net Weight

0.17 kg (0.4lbs)

Shipping Weight

0.56 kg (1.2lbs) approx.

Type

Aluminum

Cooling

Convection ventilation

Accessories

Included

1 Power adapter, 1 power cord

For the US version: 2 US Frame sets and faceplates (in black

and in white)

For the European version: 1 EU white frame, 1 UK white

frame, 1 EU/UK white faceplate

Specifications are subject to change without notice at www.kramerav.com

Altri manuali Kramer Trasmettitore

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente