Kramer TP-583T Manuale utente
TP-583T/TP-583R Quick Start (P/N: 2900-300962QS REV 1)
P/N:
2900- 300962QS
Rev:
1
Scan for full manual
TP-583T/TP-583R Quick Start Guide
This guide helps you install and use your TP-583T/TP-583R for the first time.
Go to www.kramerav.com/downloads/TP-583T, TP-583R to download the latest user manual and check if
firmware upgrades are available.
Step 1: Check what’s in the box
TP-583T HDMI Line Transmitter or
1 Power adapter and cord
1 Quick start guide
TP-583R HDMI Line Receiver
4 Rubber feet
1 Bracket set
Step 2: Get to know your TP-583T and TP-583R
TP-583T
#
Feature
Function
1
IN LED
Lights green when an active source device input signal is detected.
2
OUT LED
Lights green when an active, far-end sink (acceptor) connection is
detected via the HDBT link.
3
LINK LED
Lights green when an HDBT link is established with the HDBaseT
receiver.
4
ON LED
Lights green when the device receives power.
5
LINE RJ-45 Connector
Connect to the RJ-45 HDBT LINE connector on a receiver (for
example, TP-583R, TP-780R and so on).
6
HDMI™IN Connector
Connect to an HDMI source.
7
SETUP DIP-switches
Set the operation DIP-switches.
8
RS-232 (G, Rx, Tx) 3-pin Terminal Block Connector
Connect to a laptop to control the receiver or perform firmware
upgrade.
Connect to a controller device (for example, SL-240C) to serially
control a remote device (for example, the HDMI OUT acceptor) that
is connected to TP-583R.
9
IR 3.5mm Mini Jack Connector
Connect to an external infrared emitter / sensor.
10
12V DC Power Connector
12V DC connector for powering the unit.
TP-583R
#
Feature
Function
1
IN LED
Lights green when an active, far-end source device input signal is
detected via the HDBT link.
2
OUT LED
Lights green when an active sink (acceptor) connection is detected.
3
LINK LED
Lights green when an HDBT link is established with the HDBaseT
transmitter.
4
ON LED
Lights green when the device receives power.
5
LINE RJ-45 Connector
Connect to the RJ-45 HDBT LINE connector on a transmitter (for
example, TP-583T, TP-780Tand so on).
6
HDMI® OUT Connector
Connect to an HDMI acceptor.
7
SETUP DIP-switches
Set the operation DIP-switches.
8
RS-232 (G, Rx, Tx) 3-pin Terminal Block Connector
Connect to a laptop to control the receiver or perform firmware
upgrade.
Connect to a serially controlled device (for example, the HDMI OUT
acceptor) to enable its control by a remote controller device (for
example, SL-240C) that is connected to TP-583T.
9
IR 3.5mm Mini Jack Connector
Connect to an external infrared emitter / sensor.
10
12V DC Power Connector
12V DC connector for powering the unit.
Step 3: Install TP-583T/TP-583R
Install TP-583T/TP-583R using one of the following methods:
•Attach the rubber feet and place the unit on a flat surface.
•Fasten a bracket (included) on each side of the unit and attach it to a flat surface.
For more information go to
www.kramerav.com/downloads/TP-583T, TP-583R.
•Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/TP-583T, TP-583R).
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your TP-583T/TP-583R. For best results, we recommend that
you always use Kramer high-performance cables to connect AV equipment to TP-583T/TP-583R.
RJ-45 Pinout:
DIP-Switch Settings
For the Ethernet connector, see the wiring diagram
below:
All DIP-switches are set to Off (up) by default.
Changes to DIP-switches 4 and 5, only take
effect after power cycling the device.
PIN EIA /TIA 568B
PIN
Wire Color
#
Feature
Dip-switch Settings
1
Orange / White
1
Reserved
Set to OFF.
2
Orange
2
Compression
Level
OFF –Low compression level is applied.
ON –High compression level is applied to
gain better extension reach performance.
3
Green / White
4
Blue
5
Blue / White
3
Compressed
Signals
OFF –Compression is applied only to signal
resolutions higher than 1080p.
ON –Compression is applied to all signal
resolutions.
6
Green
7
Brown / White
8
Brown
Compression can be applied for a
TP-583T/TP-583R
paired-connection only, thus
preserving backward compatibility
with standard-HDBT extenders.
4, 5
FW Upgrade
OFF, OFF –Normal operation mode.
ON, OFF –HDBT FW upgrade mode.
ON, ON –Compression FW upgrade mode.
When either DIP-switch is set to
ON, the device extension operation
is disabled.
6
IR Frequency
Mode
OFF (up) –Frequency is 38kHz.
ON (down) –Wide-range modulated IR
frequency.
For optimum range and performance use the
recommended Kramer cables available at
www.kramerav.com/product/TP-583T, TP-583R.
Step 5: Connect the power
Connect the 12V DC power adapter to TP-583T/TP-583R and plug it into the mains electricity.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the Kramer Electronics power adapter that is provided with the unit.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information.
Step 6: Operate TP-583T/TP-583R
Operate TP-583T/TP-583R
remotely, by RS-232 serial
commands transmitted by a touch
screen system, PC, or other serial
controller
RS-232 Control
Baud Rate:
57,600
Data Bits:
8
Stop Bits:
1
Parity:
None
Command Format:
ASCII
Technical Specifications
TP-583T
Input
1 HDMI
On a female HDMI connector
Output
HDBT
On an RJ-45 connector
Port
RS-232
On a 3-pin terminal block connector for serial link extension
IR
On a 3.5mm mini jack connector
TP-583R
Input
HDBT
On an RJ-45 connector
Output
1 HDMI
On a female HDMI connector
Port
RS-232
On a 3-pin terminal block connector for serial link extension
IR
On a 3.5mm mini jack connector
General
Video
Transmitted Data Bandwidth
Up to 18Gbps (6Gbps per graphic channel)
Max Resolution
Standard compression level
4096x2160@60Hz (4:4:4) 24bpp
High compression level
3840x2160@60Hz (4:4:4) 24bpp
Compliance
HDMI 2.0, HDCP 2.2, HDR 10
Reach Extension
We recommend that you use Kramer shielded cables to achieve optimum extension ranges.
Standard Compression Level
Up to 40m (130ft) at 4K@60Hz (4:4:4)
Up to 70m (230ft) at 4K@60Hz (4:2:0) or full HD (1080p @60Hz 36bpp)
High Compression Level
Up to 70m (230ft) at 4K@60Hz (4:4:4), 4K@60Hz (4:2:0) and full HD
(1080p @60Hz 36bpp)
Extended RS-232
Baud Rate
300 to 115200
Controls
Front Panel
IN, OUT, LINK and ON LED indicators
Rear Panel
DIP-switches
Power
Consumption
12V DC, TP-583T 480mA; TP-583R 680mA
Source
12V DC, 2A
Environmental
Conditions
Operating Temperature
0° to +40°C (32° to 104°F)
Storage Temperature
-40° to +70°C (-40° to 158°F)
Humidity
10% to 90%, RHL non-condensing
Regulatory Compliance
Safety
CE, UL
Environmental
RoHs, WEEE
Enclosure
Size
Tool
Type
Aluminum
Cooling
Convection ventilation
General
Net Dimensions (W, D, H), each
12cm x 7.2cm x 2.4cm
(4.7" x 2.8" x 0.94")
Shipping Dimensions (W, D, H)
15.7cm x 12cm x 8.7cm
(6.2" x 4.7" x 3.4")
Net Weight, each
0.2kg (0.44bs) approx.
Shipping Weight
0.72kg (1.6lbs) approx.
Accessories
Included
1 Power adapter, 1 power cord and 1bracket set per device
Specifications are subject to change without notice at www.kramerav.com
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Altri manuali per TP-583T
1
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Kramer Trasmettitore
Kramer
Kramer TP-114 Manuale utente
Kramer
Kramer SID-X1N Manuale utente
Kramer
Kramer PT-571 Manuale utente
Kramer
Kramer 675T Manuale utente
Kramer
Kramer TP-590Txr Manuale utente
Kramer
Kramer Cobra TS2 Manuale utente
Kramer
Kramer TP-551N Manuale utente
Kramer
Kramer VP-300THD Manuale utente
Kramer
Kramer 671T Manuale utente
Kramer
Kramer TP-185 Manuale utente
Kramer
Kramer 650T Manuale utente
Kramer
Kramer TP-410 Manuale utente
Kramer
Kramer 610R Manuale utente
Kramer
Kramer PT-2UT/R-KIT Manuale utente
Kramer
Kramer VP-428H2 Manuale utente
Kramer
Kramer VP-5R Manuale utente
Kramer
Kramer VP-300THD Manuale utente
Kramer
Kramer DigiTOOLS KW-11T Manuale utente
Kramer
Kramer F-110 Manuale utente
Kramer
Kramer 617T Manuale utente
