Kurth Electronic KE7200 Manuale utente

Operating Manual

Ethernet Performance Tester

KE7200

LAN Cable Tester

KE7100

All reprints and electronic copies, including excerpts,

require prior written approval of

Operating Manual

KE7200 / KE7100

KURTH ELECTRONIC FERNMELDETECHNIK

www.kurthelectronic.de [email protected]

Kurth Electronic GmbH

All of the brand names and trademarks cited herein are the property of

their registered owners.

Introduction

The KE7200 / KE7100 you purchased is an easy-to-operate, intuitive

LAN tester.

Please read the entire instruction manual first to help you use the

KE7200 / KE7100 effectively.

The device was manufactured according to the following

guidelines:

73/23/EEC

DIN VDE 0800

DIN EN 61010

DIN EN 41003

DIN IEC 60068-2-1, 60068-2-2, 60068-2-3, 60068-2-14,

60068-2-27, 60068-2-6-fc, 60068-2-78, 60068-2-29

Should you have additional questions regarding the

operation and use of this device, please contact:

Kurth Electronic GmbH USA

Fernmeldetechnik KURTH ELECTRONIC Inc.

Mühleweg 11 PO Box 1377 - Sparta, NJ 07871

72800 Eningen u.A. email: sales@kurthelectronic.com

GERMANY www.kurthelectronic.com

Phone: +49-7121-9755-0

Fax: +49-7121-9755-56

email: sales@kurthelectronic.de

www.kurthelectronic.de

Operating Manual

KE7200 / KE7100

KURTH ELECTRONIC FERNMELDETECHNIK

www.kurthelectronic.de sales@kurthelectronic.de

ON-OFF

button

ESC

(back)

button

LEFT –RIGHT

controls

SEL (enter)

button

Ethernet comm

port

Test port

Display

UP –DOWN

controls

Operating Manual

KE7200 / KE7100

KURTH ELECTRONIC FERNMELDETECHNIK

www.kurthelectronic.de [email protected]

Safety Instructions

The KE7200 / KE7100 may only be operated with the accessories

originally provided. Using the device with accessories that are not original

or for applications for which it was not intended can lead to incorrect test

results and may damage the device.

The relevant safety regulations in VDE 0100, 0800 and 0805 must be

observed.

The use of cables other than those provided can damage the

device. The device should not be connected to high voltage

sources such as AC power circuits. Kurth Electronic assumes no

liability for damage resulting from improper use.

Never open the device. There are no parts in the device that need

to be serviced or calibrated. To change the battery, open the

battery compartment. See the instructions in Appendix A.

The tester is protected from splashing water and dust by the front

covering. It is not water-tight, however.

Never pull unnecessarily on the device’s cables. To hang it up, use

the eyelet in the device and the provided strap.

For end-to-end cable testing, only use the KE7010 test remote that

was supplied or which can be ordered.

Operating Manual

KE7200 / KE7100

KURTH ELECTRONIC FERNMELDETECHNIK

www.kurthelectronic.de sales@kurthelectronic.de

Table of contents

Introduction ______________________________ 2

Safety Instructions_________________________ 4

Applications:____________________________ 7

Using the KE7200 / KE7100 ________________10

Keypad __________________________________10

ESC ______________________________________ 10

ON/OFF___________________________________ 10

Four arrow buttons __________________________ 10

SEL button_________________________________ 10

Test settings______________________________10

Wiring (Main menu>Setup>Wiring)_____________ 10

Velocity (Main menu>Setup>Velocity) __________ 10

Cable Type (Main menu>Setup>Cable type) ______ 11

Device settings (Main menu>Setup>Device Setups) __11

Language __________________________________ 11

Units______________________________________ 11

Battery type ________________________________ 11

Back light__________________________________ 11

Auto Power off _____________________________ 12

Key beep __________________________________ 12

Sound_____________________________________ 12

Contrast ___________________________________ 12

Reset to factory setting _______________________ 12

Program update _____________________________ 12

Configurations___Fehler! Textmarke nicht definiert.

Test settings (Main Menu>Setup>Test Setups) ______12

Cable definition _____________________________ 12

Wiring definitions ___________________________ 12

Remote ID _________________________________ 13

MAC address_______________________________ 13

IP address (Main menu>Setup>IP address) _______ 13

Operating Manual

KE7200 / KE7100

KURTH ELECTRONIC FERNMELDETECHNIK

www.kurthelectronic.de [email protected]

Testing with the KE7200 / KE7100 ____________ 13

Cable test (Main menu)________________________13

Performing the test ___________________________14

Save the data ________________________________15

Cable/wire trace _____________________________15

PoE/PoE+ test per IEEE 802.3af/at ______________16

IP test______________________________________16

Transmit measurements _______________________17

Appendix A ______________________________ 18

Changing the battery__________________________18

Test settings _____________________________ 18

Cable definitions (Main menu>Setup>Test setups>Cable

definition) __________________________________18

Wiring definitions (Main menu>Setup>Test setups>Wiring

definition) __________________________________18

KE Manager ______________________________ 20

Installing the KE Manager _____________________20

Functions___________________________________20

PC setup ___________________________________20

Starting the KE Manager ______________________20

The following selection options are offered: _______21

Load data (PC) ______________________________21

Save data ___________________________________21

Save displayed data___________________________21

Delete selected line ___________________________21

Print data___________________________________21

Print options ________________________________21

Configuration table ___________________________21

Update_____________________________________21

Instructions _____ Fehler! Textmarke nicht definiert.

Manager function _________________________ 21

Selecting/sorting by customer___________________21

Customer address ____________________________22

Display results_______________________________22

Overview of technical data__________________ 23

KE7200 / KE7100 Ethernet Performance Tester ____23

Operating Manual

KE7200 / KE7100

KURTH ELECTRONIC FERNMELDETECHNIK

www.kurthelectronic.de sales@kurthelectronic.de

Applications:

Testing and starting up 10/100/1000 Mbit LAN networks,

Verifying new LAN installations

Troubleshooting existing LAN installations

Logging network tests

Cable mapping

Fault finding

Testing PoE/PoE+ performance

Measuring length, finding cables of all kinds, coaxial cables,

etc.

KE7200 only:

IP tests; static or with DHCP

Ping and stress tests

Storage of Measurements

Measurement and display of:

Cable test

- Mis-wiring

- Short circuit

- Open circuit

- Split pair

- Length of cables and wires with TDR up to 150 m

- External voltage

Power over Ethernet

- PoE Version A or B

- Available power in Watts according to IEEE 802.3af/at

Cable/port

- Link Light Blink with Normal Link Pulse

- Transmit 4 different trace tones

Operating Manual

KE7200 / KE7100

KURTH ELECTRONIC FERNMELDETECHNIK

www.kurthelectronic.de [email protected]

KE7200 only:

Test active 10/100/1000 Mbit network

- Information about service type

- Static IP or DHCP

- Network scan

- List all found subscribers

- Display name, IP address, MAC address

- Targeted ping of individual addresses

- Display lost responses, min/max/average response times

- Stress test devices by constant ping

- Ping frame size adjustable from 32 to 1024 bytes

Other

- 16 different predefined wiring versions

- Original predefined versions can be created

- Cable types with predefined VP value

- Original cable types can be created

- Illuminated graphical display

- Automatic shutoff time can be set

- Display illumination time can be set

KE7200 only:

- Save the results in the device and PC

- Printout using a PC with the KE Manager software

Remote KE7010 unit

- Active remote unit with microprocessor

- Display of pass/fail with green LED

- Remote ID programmable from 1–32

- Max. 32 remotes

Operating Manual

KE7200 / KE7100

KURTH ELECTRONIC FERNMELDETECHNIK

www.kurthelectronic.de sales@kurthelectronic.de

Power supply

4 x UM-3 / AA battery or 4 x rechargeable batteries of the

same size

Battery life with a good quality battery

(such as a GP Super Alkaline or Varta Industrial)

Measurement always with the illuminated display

- Powered on with no testing: approximately 40 hours

- Cable test without remote: approximately 35 hours

- Cable test with remote: approximately 18 hours

- IP test: approximately 15 hours

The available testing time can be extended by turning off

the device or limiting the display lighting time.

Note: Testing is continuous. Different durations may

result with batteries of different quality. Only use

batteries from the same manufacturer with the same

capacity. Remove the batteries if the device will not be

used for a long time. If the battery compartment is

damaged by leaking batteries, it can be exchanged.

Operating Manual

KE7200 / KE7100

KURTH ELECTRONIC FERNMELDETECHNIK

www.kurthelectronic.de [email protected]

Using the KE7200 / KE7100

Keypad

When the KE7200 / KE7100 was developed, emphasis was placed on

fast and easy operation. For this reason, the KE7200 / KE7100 has only

seven buttons despite its many test options.

ESC

Similar to a PC, the ESC button means “undo the last step.”

ON/OFF

Button for turning the device On and Off. This button has a delay of

approx. 1 sec. when turning off.

Four arrow buttons

The arrow buttons are for menu scrolling UP▲ /DOWN ▼and LEFT◄

/RIGHT►.

SEL button

The SELECT button. Press this button to select a function or start a test.

Similar to a PC Enter key.

Test settings

Wiring (Main menu>Setup>Wiring)

You can select from the list of different possible types of wiring (which pin

to which wire). This can even be changed during the cable test. It is

important to precisely specify the correct type of wiring because a

Pass/Fail result relies on it. The proper identification of errors in the case

of split pairs also requires a precise definition.

Sixteen popular versions are predefined. The following abbreviations are

used:

UTP = Unshielded Twisted Pair in a cable

STP = Shielded Twisted Pair in a cable

CR = cross connected cable

Velocity (Main menu>Setup>Velocity)

This is the propagation velocity (VP) of the signal in the cable expressed

as a fraction of the speed of light. This information is necessary to

Altri manuali per KE7200

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Kurth Electronic Apparecchiature di prova

Kurth Electronic

Kurth Electronic xDSL MultiTest KE3700 Manuale utente

Kurth Electronic

Kurth Electronic xDSL MultiTest KE3700 Manuale di istruzioni

Kurth Electronic

Kurth Electronic KE7200 Manuale utente

Kurth Electronic

Kurth Electronic KE7200 Manuale utente

Kurth Electronic

Kurth Electronic KE7100 Manuale utente

Kurth Electronic

Kurth Electronic CCTS-03 Manuale utente

Kurth Electronic

Kurth Electronic KE301 Manuale utente

Kurth Electronic

Kurth Electronic xDSL MultiTest KE3700 Manuale di istruzioni

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente