Lantech IPGS-0016 Manuale utente
Lantech
IPGS-0016
16 10/100/1000T Industrial Unmanaged PoE
Ethernet Switch
IPES-0016
16 10/100TX Industrial Unmanaged PoE
Ethernet Switch
User Manual
V1.01
Mar. 2022
Recommendation for Shielded network cables
STP cables have additional shielding material that is used to reduce external interference. The
shield also reduces the emission at any point in the path of the cable. Our recommendation is
to deploy an STP network cable in demanding electrical environments. Examples of
demanding indoor environments are where the network cable is located in parallel with
electrical mains supply cables or where large inductive loads such as motors or contactors are
in close vicinity to the camera or its cable. It is also mandatory to use an STP cable where the
power device (like IP camera) is used outdoors or where the network cable is routed outdoors.
Content
Overview............................................................1
Introduction .............................................................. 1
Model Lists...............................................................1
Packing List.............................................................. 2
Safety Precaution.....................................................2
Hardware Description.........................................3
Front Panel...............................................................3
Top View .................................................................. 4
Dimensions .............................................................. 4
Wiring the Power Inputs...........................................6
Wiring the Fault Alarm Contact ................................6
LED Indicators..........................................................8
RJ-45 Pin Assignments............................................9
Cabling...................................................................11
Mounting Installation........................................12
DIN-Rail Mounting.................................................. 12
Wall-Mount Plate Mounting....................................14
1
Overview
Introduction
The unmanaged industrial switch is a cost-effective solution and meets
the high reliability requirements demanded by industrial applications.
Model Lists
Model name
10/100/1000T
ports
10/100TX
ports
PoE ports
IPGS-0016-24V
IPGS-0016-24V-E
16
-
16
IPES-0016-24V
IPES-0016-24V-E
-
16
16
For latest product specifications, please refer to Lantech official site.
2
Packing List
1 x 16-port Industrial Ethernet Switch
1 x Terminal Block
Safety Precaution
Attention
If DC voltage is supplied by an external circuit, please use a
protection device on the power supply input.
3
Hardware Description
For POE models: Do not use units POE ports to uplink to another unit. (May Cause
Damage) Lantech strongly advise the installation of a Galvanic isolated DC/DC
converter between the power supply and the Ethernet switch on all Non-Isolated
units. Please contact the sales team for advice on which units support isolated
power supply.
In this paragraph, we will introduce the Industrial switch’s dimensions,
port, cabling information, and wiring installation.
Front Panel
The Front Panel of the IPGS-0016/ IPES-0016 are shown as below.
4
Front Panel of the Industrial Switch
Top View
The top panel of the Industrial Switch is equipped one terminal block
connector of two DC power inputs.
Top panel of the Industrial Switch Converter
Dimensions
5
. The dimensions of IPGS-0016/IPES-0016 are 74 x 152 x 105 mm (W x
H x D). The figure below gives the dimensions and views of each side of
the 16-port Industrial Ethernet Switch.
6
Wiring the Power Inputs
Please follow the steps below to insert the power wire.
1. Insert the positive and negative wires into the V+ and V- contacts on the
terminal block connector.
2. To tighten the wire-clamp screws for preventing the DC wires to loose.
Wiring the Fault Alarm Contact
The fault alarm contact is in the middle of terminal block connector as the
picture shows below. Inserting the wires, it will detect the fault status
which the power is failure or port link failure (for managed model) and form
an open circuit.
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali Lantech Interruttore
Lantech
Lantech IES-2208CA Manuale utente
Lantech
Lantech IPES-5416T Series Manuale utente
Lantech
Lantech TGS-R6616XFT Manuale utente
Lantech
Lantech LGS-2424C Manuale utente
Lantech
Lantech TPGS-L6216XT Manuale utente
Lantech
Lantech IPGS-0204DSFP-12V Manuale utente
Lantech
Lantech IPES-5408T-X-IGN Series Manuale utente
Lantech
Lantech IPES/IES-0008B Series Manuale utente
Lantech
Lantech TPGS-L6208XT Manuale utente
Lantech
Lantech LPGS-2424C Series Manuale utente
Lantech
Lantech LPES-2208CA Manuale utente
Lantech
Lantech IPES-0005B Series Manuale utente
Lantech
Lantech IES-0008B Series Manuale utente
Lantech
Lantech IPWMR-3204DF Manuale utente
Lantech
Lantech IPGS-0005T-4-12V Manuale utente
Lantech
Lantech IGS-3208MGSFP Manuale utente
Lantech
Lantech IPES-0008B Series Manuale utente
Lantech
Lantech IPES-0008A Series Manuale utente
Lantech
Lantech IPES-5408T-43 Manuale utente
Lantech
Lantech IPGS-0005T-4 Manuale utente
