Larin METS-1 Manuale utente

Model# METS-1 Mobile Engine Testing Station

Owner’s Manual

any shape or form without the express written consent of Larin Corp. Diagrams within this manual may not be drawn proportionally.

Due to continuing improvements, actual product may di󰀨er slightly from the product described herein. Tools required for assembly

and service may not be included.

IMPORTANT: Please keep your receipt in a safe, easy to nd location, as you will need it for any warranty/repair issues that may

arise.

Read all instructions and safety warnings before using this product. Failure to follow the instructions and safety warnings

may result in personal injury or property damage.

For Customer Service please email to serv[email protected] or call 1-800-87-LARIN (1-800-875-2746)

Monday – Friday 8:00am to 4:30pm PST

WARNING

Engine Not Included

Page 2

WARNING

GENERAL SAFETY RULES

CAUTION: Do not allow persons to operate or assemble this product until they have read this manual and have devel-

oped a thorough understanding of how it works.

WARNING: e warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible

conditions or situations that could occur. It must be understood by the operator/user that common sense and caution

are factors which cannot be built into this product, but must be supplied by the operator/user.

SPECIFICATIONS

Max. Load Capacity: 1000 lb

Dimensions: 46”L x 32.5”W x 37”H

Fuel Tank Size: 1 gallon

1. Study, understand, and follow all instructions before operating this device.

2. Use only on hard, level surface.

3. Do NOT exceed the rated capacity of 1,000lbs for this product.

4. Any Engine Station that appears to be damaged in any way, is found to be worn, or operates abnormally shall be

removed from service immediately until repaired.

5. If it is believed that the Engine has been subjected to abnormal load, or shock, it shall be removed from service

immediately until fully inspected.

6. Assure load is centered and secured to mounting attachments before moving or testing. O-center loads may make

the load unstable.

7. Because of potential hazards associated with this type of product,

NO alterations shall be made to the product.

8. Following safety rules of gasoline use.

8. Only attachments and/or adapters supplied by the manufacturer shall be used.

9. Use caution when making all of the connections.

10. Follow engine testing procedures and precautions as specied by the engine manufacturer’s owner’s/repair manual.

11.Failure to heed these markings/warnings may result in personal injury and/or property damage.

ASSEMBLED

Page 3

PARTS LIST AND DIAGRAM

Note: Some parts listed and shown are

for illustration purposes only, may not be

available as replacement parts.

Part # Description Qty Part # Description Qty

1 Le Side Frame Tube (B) 1 19 Fuel Tank Strap 2

2 Right Side Frame Tube (C) 1 20 Fuel Tank 1

3 Rear End Frame Tube 1 21 Support Strap 2

4 Cross Member Frame Tube 2 22 Nut M12 2

5 Front End Frame Tube (E) 1 23 Flat Washer d12 4

6 Swivel Caster 2 24 Spring Washer d12 2

7 Rigid Caster 2 25 Nut M8 8

8Sleeve 2 26 Flat Washer d 8 28

9 Black Sleeve with Post 4 27 Spring Washer d 8 8

10 readed Rod 2 28 Bolt M8 X 20 8

11 Tray 1 29 Bolt M8 X 65 10

12 Tray Support 1 30 Locknut M8 20

13 Long Vertical Post 2 31 Bolt M8 X 50 10

14 Dash Panel/Gauges 1 32 Bolt M10 X 65 2

15 Short Vertical Post 2 33 Flat Washer D10 2

16 Horizontal Bar 1 34 Locknut M10 2

17 Engine Support Strap 2 35 Inlet Water Adapter 1

18 Engine Support 2 36 Outlet Water Adapter 1

1 ignition key switch , 4 position, 12v

Gauges: size 52mm, 12v

1 oil pressure

1 oil/water temperature

1 tachometer

Page 4

ASSEMBLY INSTRUCTIONS

Tools Needed for Assembly:

Crescent Wrench, Phillips Screwdriver, 13mm Wrench, 14mm Wrench, 17mm Wrench, 19mm Wrench

For all of the following steps, please refer to Parts Diagram, Parts List and Illustrations.

STEP 1 Unpack Testing Station and verify that you have received all of the parts as indicated on the parts list.

STEP 2 Place Le Side Frame Tube B Part # 1 and Right

Side Frame C Part# 2 on the oor with the 6 holes on the

top. Make sure that the holes are closer to the outer edge

of the metal parts and that the two holes on the sides are

closer to the top than to the bottom. See Illustration A.

STEP 3 Attach Swivel Casters (#6) to Front

End Frame Tube E (#5) using four of the

M8x20 bolts (#28),Flat washers(#26),Spring

washers(#27), and M8 nut(#25). two for each

caster. See Illustration 1.

STEP 4 Attach Rigid Casters (#7) to Rear

End Frame Tube (#3) using four of the M8x20

bolts (#28),Flat washers (#26),Spring wash-

ers(#27), and M8 nuts(#25). two for each

caster. See Illustration 2.

Page 5

STEP 5 Place Cross Member Frame Tube

(#4) on the oor. Slide the Black Sleeve with

Post (#9) onto the Cross Member Frame Tube

(#4). Next slide another Black Sleeve with Post

(#9) onto the Cross Member Frame Tube (#4).

Next insert the Sleeve (#8) into the end of

Cross Member Frame Tube (#4) as shown in

Illustration 3.

STEP 6 Slide Cross Member Frame Tube

(#4) onto Le and Right Side Frame Tubes

B,C (#1 and #2). Next slide the other

Cross Member Frame Tube (#4) onto the

Le and Right Side Frame Tubes B, C (#1

and #2) as shown in Illustration 4.

STEP 7 Slide the readed Rods ( #10 ) through D12 Flat Washer (#23), Front End Frame Tube E (#5) into the ends of Le and

Right Side Frame Tubes (#1 and #2). Make sure it is the side that has three holes and all holes are on top area of the tubes.

See Illustration 5.

Make sure marker B on Le Side Frame Part# 1 meets with marker B on the Front End

Frame Tube (E) Part # 5, marker C on Right Side Frame Part# 2 meets with C on Part 5. See

Illustration 5.1 below.

STEP 8 Place Rear End Frame Tube (#3) onto the

ends of the readed Rods (#10) at the opposite

end of Le and Right Side Frame Tubes (#1 and

#2). Fasten with M12 nut D12 Flat Washer (#23)

and D12 Spring washer (#24). See Illustration 5.

STEP 9 Using M8x65 bolt (#29), attach Swivel

Casters (#6) to Le and Right Side Frame Tubes

(#1 and #2). Fasten with M8 Locknut (#30) , and

D8 Flat Washer (#26). Next, also using the long

bolt (#29), attach Rigid Casters (#7) to Le and

Right Side Frame Tubes (#1 and #2) on opposite

end. Fasten with M8 Locknut (#30) , and D8 Flat

Washer (#26) . See Illustration 5.

Illustration 5

Illustration 5.1

Page 6

STEP 10 Place the Long Vertical Posts (#13) onto the vertical posts on the Front End Frame Tube (#5). Attach the Support Straps

(#21) to the Le and Right Side Frame Tubes (#1 and #2) using the M8x65 bolts (#29) , D8 Flat Washers (#26) and M8 Locknut

(#30) . See Illustration 6.

STEP 11 Place the remaining Short Vertical Posts (#15) over the vertical posts of the attached Black Sleeves with Posts (#9). Attach

with M8x50 bolts (#31) , D8 Flat Washers (#26) and M8 Locknut (#30). See Illustration 6.

STEP 12 Place two of the Engine Support (#18) onto vertical posts of the attached Black Sleeves with Posts (#9). Attach with

M8x50 bolts (#31) , D8 Flat Washers(#26) and M8 Locknut (#30). See Illustration 6.

STEP 13 Attach Tray Support (#12) to Le and Right Side Frame Tube (#1 and #2) using long bolts (#35). Place Tray (#11) on top

of Tray Support (#12) and Front End Frame Tube (#5). See Illustration 6.

STEP 15 Place Dash Panel (#14) on top

of Long Vertical Posts (#13). Attach with

M8x65 bolts (#29) , D8 Flat Washers (#26)

and M8 Locknut (#30) . See Illustration 7

STEP 14 Place Horizontal Bar (#16) on top

of Short Vertical Posts (#15). Attach with

M8x65 bolts (#29) ,D8 Flat Washers (#26)

and M8 Locknut (#30) . See Illustration 7.

Page 7

STEP 16 Place Engine Support

Strap (#17) onto Horizontal Bar

(#16). Attach with M10x65 bolt

(#32) , D10 Flat Washer (#33) ,

M10 Locknut (#34) .

See Illustration 8.

STEP 17 Slide Fuel Tank (#20)

into Fuel Tank Straps (#19).

Attach Fuel Tank Straps (#19) and

Dash Panel (#14) using M8x65

bolts (#29), D8 Flat Washer (#26)

and M8 Locknut .

See Illustration 8.

DIRECTIONS FOR USE

Use Precautions

Failure to heed these instructions may result in personal injury and/or property damage:

1. Study, understand, and follow all instructions before operating this device. Use as intended only.

2. Do not exceed rated capacity. Be aware of dynamic loading! Sudden load movement may briey create excess load causing

Product failure.

3. Use only on hard, level surfaces. Surfaces must be dry, clean and free from oil or grease.

4. Lock and chock wheels before applying a load.

5. Assure load is centered and secured to mounting attachments.

6. Wear ANSI-approved safety goggles and heavy-duty work gloves during use.

10. Inspect before every use, do not use if parts loose or damaged.

11. is product is not a toy. Do not allow children to play with or near this item.

12. Check and clean fuel tank before each use.

13. Secure the engine to the Testing Station as instructed.

Mounting Engine

TO PREVENT SERIOUS INJURY:

Before attaching an engine to the stand, conrm that its weight does not exceed the Stand maximum capacity.

1. Determine the thread type and length of bolts (not included) needed to thread into the engine block.

2. Align the Engine Supports and Straps part# 17 and 18 with four mounting bolt locations on the engine.

3. Place the bolts (not included) through engine supports and straps and securely tighten them into the engine.

7. Slowly lower the hoist/engine crane (sold separately) until all the engine’s weight is held by the stand.

8. Safely release the engine from the hoist/engine crane.

Removing Engine

Secure the engine properly to the crane. Use the crane to support all of the engine’s weight directly overhead, once the

engine is properly supported by the crane, remove the bolts securing the Engine Supports and Straps Part# 18/17 to

the engine.

Helpful using tips refer to Figure 1, 2, 3.

ASSEMBLED

Page 8

Small block Chevrolet header (73 pickup)

Turbo muers with 2”dia x 6”length tubes on each side of muers.

Engines can be placed in this manner or sideways or backwards on

stand.

REAR

Engine mounting straps, using

last boltholes on straps to attach

bell housing to bow.

FRONT

Factory motor mount

pockets most engines.

ENGINE MOUNTING

FIGURE 1

FIGURE 2

Attach home sized garden hoses to water adapters.

ermostat is NOT used, and the water pump remains

stationary (not spinning). It is important to run the

water in the correct direction, otherwise hot spots may

occur inside the engine and possible damage. Start with

a small amount of water. Watch the temperature gauge,

regulate to 160, 170, 180, as necessary.

Turn water o IMMEDIATELY upon turning the

engine o. us, eliminating the risk of cracking the

hot block or heads with cold water entering the engine.

Let engine cool down by itself.

Page 9

WIRING SYSTEM

NOTE

Ballast resister cuts battery voltage down to

about 7 volts for long point life. If you need 12

volts either eliminate or bypass resister.

NOTE

Most parts houses have in line universal type

fuel pumps that are about the size of an in line

fuel lter and make for a nice installation.

NOTE

Use radiator hose clamps to clamp fuel pump,

coils and ballast resister to the legs of the bow

under the panel with weather stripping in

between the two.

FIGURE 3

Keyed Positions 12 v ACC-OFF-IGN-START

ACC

OFF

Position

Terminal

Clockwise

1 (B) 2 3 4

Page 10

LARIN CORP. Warrants to the original purchaser that this product is free from defects in materials

and workmanship for the period of 90 days from the date of purchase. is warranty does not apply to

damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside

our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We

shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special

or consequential damages arising from the use of our product. Some states do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to

you. is warranty is expressly in lieu of all other warranties, express or implied, including the warranties of

merchantability and tness.

For warranty service, the product or part must be returned to us with transportation charges prepaid along

with Proof of purchase, and an explanation of the complaint. If our inspection veries the defect, we will

either repair or replace the product at our election or we may elect to refund the purchase price if we cannot

readily and quickly provide you with a replacement. We will return repaired products at our expense, but if

we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty,

then you must bear the cost of returning the product.

is warranty gives you specic legal rights and you may also have other rights which vary from state to state.

LIMITED NINETY DAYS WARRANTY

For warranty service, please return the product prepaid to

Larin Corporation

5651 Schaefer Avenue,

Chino, California 91710.

Email: service@larincorp.com

Be certain to include your name and address, email address, proof

of purchase date and description of the problem.

NOTE

e diagrams and directions are for reference only, please consult a ASE qualied auto technician for correct installation.

Altri manuali per METS-1

Indice

Altri manuali Larin Apparecchiature di prova

Larin

Larin METS-1 Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente