Larson Electronics EPL-QC-16C-1X150LED-RT-100-EPP Manuale utente

EPL-QC-16C-1X150LED-RT-100-EPP

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

150W EXP LED Light Cart Mount - Quick Change Mount

17,500 Lm - C1D1 - 100' 16/3 SOOW - EXP Plug

Instruction Manual

This explosion proof wheelbarrow light is designed for illumination of industrial locations. It uses the latest in

solid state lighting technology for long life, low maintenance and high efficiency.

The unique design focuses the light where it is needed, giving improved efficiency over a conventional HID

luminaire.

An internal, universal input, power-factor-corrected switch-mode supply allows it to be used from any nominal

120-277V AC 50/60 Hz power supply without any variation in light output.

WARNING

To avoid the risk of fire, explosion or electric shock, this product should be installed, inspected and

maintained by a qualified electrician only, in accordance with all applicable electrical codes.

To avoid electric shock:

Be certain electrical power is OFF before and during installation and maintenance.

Luminaire must be connected to a wiring system with an equipment-grounding conductor.

To avoid explosion:

Make sure the supply voltage is within the luminaires’ voltage rating.

Ensure the marked T rating is less than the ignition temperature of the Hazardous Atmosphere.

Do not operate in ambient temperatures above those indicated on the luminaire nameplate.

Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

The light fixture on this wheelbarrow cart is factory sealed.

CART OPERATION

The wheelbarrow cart assembly consists of 2 parts:

1. Light head

2. Wheelbarrow cart base

To assemble cart, insert light head over center hole of wheelbarrow cart and tighten hand screw. The

wheelbarrow cart is now ready for use.

Tilt cart using both handles and maneuver like a wheelbarrow. Simply roll entire assembly to a new location

once assembled. Make sure light head is secure prior to maneuvering cart.

WARNING: Be sure all hand screws are tight before transporting! Use caution when maneuvering near

inclines or drop offs.

Run power cord to a nearby receptacle outputting voltage listed on product label.

WARNING: check nameplate for proper voltage. Damage from improper voltage may void warranty.

To adjust light head vertically, loosen hand screws on either side. Once desired angle is achieved, tighten

both hand screws to secure light in its place. Loosen the single hand screw holding light head to rotate

horizontally. Be sure all hand screws are tight before transporting!

EPL-QC-16C-1X150LED-RT-100-EPP

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

MOUNTING

The quick change mounting system allows for quick mount and dismount from the mounting base. To remove,

loosen the center collar towards the base of the mount to free the base in order to remove it from the cart.

Twist counter-clockwise until loose, lift collar and slide light head away from the base. Follow these steps in

reverse order for attaching light head.

WIRING (see attached wiring diagram)

This unit comes preconfigured with selected cord cap, color temperature, and beam angle. Once deployed,

plug cord cap into compatible receptacle with Voltage: 120-277 Volts AC, 50/60Hz Follow all applicable

local, state, and National Electrical Code for the hazardous area!

MAINTENANCE

Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before

performing maintenance.

Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void

the warranty.

1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine

checks to be made on a yearly basis. Frequency of use and environment should determine this. It is

recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:

Recommended practice for Electrical Equipment.

2. The lens should be cleaned periodically as needed to ensure continued photometric performance.

Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid

cleaner.

3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions or

contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.

4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS. SHOULD FURTHER

INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT SALES@LARSONELECTRONICS.COM OR BY PHONE AT

1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

WARNING: CHECK NAMEPLATE

FOR PROPER VOLTAGE. DAMAGE

FROM IMPROPER VOLTAGE WILL

VOID WARRANTY.

Indice

Altri manuali Larson Electronics Attrezzatura di illuminazione

Larson Electronics

Larson Electronics BL24-LED-600V-100-HD Manuale utente

Larson Electronics

Larson Electronics HALD-48-1X4-2X50LED Manuale utente

Larson Electronics

Larson Electronics EPL-QC-16C-2X150LED-RT-X24V-C1D1-12.3-100-EPP Manuale utente

Larson Electronics

Larson Electronics GL-2051-F-M Manuale utente

Larson Electronics

Larson Electronics EPLC2-QP-1X150LED-100 Manuale utente

Larson Electronics

Larson Electronics HAL-RSL Series Manuale utente

Larson Electronics

Larson Electronics GL-2051-M Manuale utente

Larson Electronics

Larson Electronics GAU-EMG-2X2W-8H Manuale utente

Larson Electronics

Larson Electronics EMGBALL-LED3 Manuale utente

Larson Electronics

Larson Electronics EXP-EMG-EXT-LE6-3L Manuale utente

Larson Electronics

Larson Electronics EPL-150LED-RT-SP0010-200C Series Manuale utente

Larson Electronics

Larson Electronics EPL-18C-150LED-RT-125C Manuale utente

Larson Electronics

Larson Electronics FRL-4P-S1-60-1X-T5HO-130W-UVC Manuale utente

Larson Electronics

Larson Electronics EPLC2-LED-50W-RT-JB5 Manuale utente

Larson Electronics

Larson Electronics C1D2 Manuale utente

Larson Electronics

Larson Electronics IND-RL-HDB-BX9-120V Manuale utente

Larson Electronics

Larson Electronics EXP-EMG-2L-LE6 Manuale utente

Larson Electronics

Larson Electronics GL-9051-F-M Manuale utente

Larson Electronics

Larson Electronics ORS-120-8M-4X150W-LED Manuale utente

Larson Electronics

Larson Electronics LEDB-4-IR Manuale utente

Larson Electronics

Larson Electronics EPL-PM-50LED-100 Manuale utente

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-100-EPP Manuale utente

Larson Electronics

Larson Electronics LEDP5W-60XC-1227 Manuale utente

Larson Electronics

Larson Electronics EPLC2-LED-150W-RT-EB Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente